hapter 08, Practice Problem 8.02 Water flows in a tube that has a diameter of D= 0.3 m. (a) Determine the Reynolds number if the average velocity is 20 diameters per second. (b) Repeat the calculations if the tube is a nanoscale tube with a diameter of D= 150 nm. (a) Re (b) Re= Click if you would like to Show Work for this question: Open Show Work

hapter 08, Practice Problem 8.02 Water flows in a tube that has a diameter of D= 0.3 m. (a) Determine the Reynolds number if the average velocity is 20 diameters per second. (b) Repeat the calculations if the tube is a nanoscale tube with a diameter of D= 150 nm. (a) Re (b) Re= Click if you would like to Show Work for this question: Open Show Work

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Use g=32.2 */sec2 (9.81 m/s2) and 60°F (16°C) water unless told to do otherwise.• Google schedule-40 pipe’s thickness at different nominal size to obtain the innerdiameter of the pipe for accurate determinaLon of flow velocity.• Must show your work to support your selecLon. Otherwise, no points will be given.• No peer discussion is allowed.1. A schedule-40 pipe necks down from 24 in at point A to 12 in at point B. 8 *3/sec of 60°Fwater flow from point A to point B. The pressure head at point A is 20 *. FricLon is insignificantover the distance between points A and B. What are the magnitude and direcLon of theresultant force on the water? (A) 2900 lbf; toward A(B) 3500 lbf; toward A(C) 2900 lbf; toward B(D) 3500 lbf; toward B
) where AP is the static The Hagen-Poiseuille equation for the laminar flow through a circular pipe is: AP pressure drop measured over some length of pipe, L. Use the Hagen-Poiseuille equation and the Darcy-Weisbach equation to derive an expression for the fanning friction factor, f, for laminar flow through a circular pipe where Re is the Reynolds number. Choose one answer from the list below: of= of O None of the above 32 Re 16 Re O f = 64 Re = o f = 32μLc 3 d² 8 Re O f = 16 Re
On a single plot, plot three curves that show the relationship between the pressure generated by thepump as a function of flow rate of water at 20 °C through the three branches of the piping systemshown below. Delta P on y axis and flow rate on the x axis. The pressure range is 0 to 1 MPa. (Branches 1 and 3 are in the same plane; branch 2 is located 5 m above the other two branches. Pipe inner diameter: 0.0254 mPipe material: copperTypical mass flow rate of interest: 0.5 kg/sIgnore minor losses of tee's at points A and B and any features of branch 3Consider minor losses of two 90° elbows in branch 2
B1. A water with viscosity 11.4x10-3 poise is flowing through a pipe of diameter 300 mm at the rate of 500 litres per sec. Find the Reynold's Number & the head lost due to friction in the pipe of length 1 km. (Enter only the values by referring the unit given. Also upload the hand written answers in the link provided) The velocity of flow of water (in m/s) is The value of Reynold's Number is The frictional loss in the pipe (in m) is
I6 a) Determine the radial positions of a pitot tube for a 6-point traverse in a 0.3 m inner diameter pipe. Show your calculations. b) If the fluid velocity measured at the pipe center is 0.3 m/s and yields a Reynolds number based on local velocity of 4000, what is the fluid cross-sectional average velocity in the pipe? c) At what value of Re is the discharge coefficient of an orifice meter approximately independent of geometry and flow rate?
SOLVES TEP BY STEP DONT USE CHATGPT DONT USE AI 3. An oil of viscosity 1.8 cp and relative density 0.8 is contained in an open tank located above the application site. A 1.5-inch diameter pipe extends vertically from the bottom of the tank and is 5 m long. The oil level in the tank remains constant at 3 m above the bottom of the tank. In a case with friction the discharge speed can be obtained in the form of the following Equation. Calculate the flow rate of oil discharged per hour. Assume that the pipe is commercial steel (ε=0.05 mm). V= 2gh +f-
1-A steel discharge pipe with a roughness equal to 0.5 mm is 800 m long and pumps 265 m³ of water per hour at a temperature of 20°C. The pipe diameter is 25 cm. Calculate the head loss. Data: kinematic water viscosity equal to 10-6 NOTE: if necessary, use Moody's DiagramHelp?
Directions: Solve the following problems completely, and make a detailed solution. Any incompletesolution arriving at such answers will never be considered. A 1124gpm of water is flowing in a round pipe such that the flow remains laminar.What is the diameter of the pipe in inches necessary to ensure laminar flow? Usekinematic viscosity of 4398 stokes.
Calculations involving retention time involve the following formula, T =, where V is volume and Q is flow rate. Often times, you will be required to calculate the volume of more than one tank and determine a rate of flow, given a total retention time. Tank 1 Tank 2 Let's assume that the total retention time for the entire system is 55 minutes, and we want to know the inlet flow, given the dimensions of tank 1 are : 14m x 10m x 3 m, and tank 2 are: 5m x 10m x 3 m. Calculate the inlet flow.
Duct Pressure Drop: Determine the pressure drop, in inches of H20, for 300 feet of 12" diameter duct with 600 CFM of air flow. If the size is reduced to 10", what is the pressure drop? If the duct is instead changed to a rectangular duct 10"x14", what is the pressure drop?. Duct sizing: When reviewing the mechanical plans for an office building, you notice that the ME has run an 18" diameter duct above a ceiling where you know there is a beam obstruction. You determine that there is a maximum of 12" of space between the top of the ceiling and the bottom of the beam. If this duct carries 2,000 CFM, determine the equivalent rectangular size of ducting that you would propose the engineer, so that the pressure drop remains similar. What is the resultant velocity (FPM) in both the round duct and the rectangular duct?
The ratio of entry diameter with exit diameter is 0.4 in a control volume of pipe segment. What is the corresponding ratio of entry to exit velocity? Recall Q1=Q2 and v1A1=v2A2 Correct answer has a margin of 0.1 from exact answer.
Determine the pressure drop over a reducer with the following conditions: Fluid density: 25 kg/m3Fluid velocity: 1.5 m/sFluid viscosity: 0.001 Pa*sInlet diameter: 0.12 mOutlet diameter: 0.019 mPipe absolute roughness: 4e-4 m Give your final answer in Pa, rounded to the nearest whole number. [Ignore entrance/exit losses and velocity loss terms]