H.W.10.5. The following data for steam condenser: Steam condensed = 50000 kg/h Temperature of steam in condenser = 40 °C Dryness of steam entering into condenser = 0.85 The air leakage in the condenser = 150 kg/h Temperature of the condensate = 35 °C Find, 1. The air leakage pressure 2. Quantity of cooling water passed through the condenser per hour if the rise in cooling water temperature is limited to 10 °C

H.W.10.5. The following data for steam condenser: Steam condensed = 50000 kg/h Temperature of steam in condenser = 40 °C Dryness of steam entering into condenser = 0.85 The air leakage in the condenser = 150 kg/h Temperature of the condensate = 35 °C Find, 1. The air leakage pressure 2. Quantity of cooling water passed through the condenser per hour if the rise in cooling water temperature is limited to 10 °C

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1. A heat exchanger is located on the roof of a warehouse to heat the air in winter. It is a coil-shaped pipe into which water vapor enters at 0.1 MPa and 300 °C and leaves with a quality of 30%. The warehouse has the following dimensions: 80m x 160m x 10m. The air must be heated from 5°C to 22°C. a. What must be the mass flow rate of the water to heat the air in less than half an hour? b. We want to cool the steam from the exchanger outlet and bring it up to 50 °C. For this, a mixing chamber with water at 20 °C is used, what will be the proportion of the steam mixture? c. The exchanger is damaged and only liquid water can be used at the same pressure (inlet T. 1 °C below saturation and outlet T. at 30°C). How long does it take to heat the air with the same flow of water?
Simulates the following thermodynamic cycle. Flow rate (Refrig-23) R-23 is 1 kg per hour and the pressure pressure in all converters is zero. Find the flow rate (Refrig-22) of R-22 in kgmole / h and W1. Compressors have an adiabatic range of 75%. (FP.PR)
1. Steam is generated at 4.20 MPa and 460°C and condensation occurs at 0.105MP.. a. For a rankine engine operating between these limits compute the thermal efficiency and the heat rate. b. Considering that a Rankine cycle occurs between the same limits, determine Q.. Q,, w. and e C. What mass flow rate is required for a net output of 35,000 kW?
ROOM (2) 700kPa x=0 CONDENSER (1) 40°C 700kPa EXPANSION VALVE (3) 100kPa EVAPORATOR (4) 100kPa x=1 OUTSIDE Consider a heat pump cycle operating with R134-a fluid at 0.01kg/s mass flow rate. Conditions are given in the figure. a) What are the values of heat supply rate to the room and heat absorption rate from the outside? b) What is COP of this heat pump? c) Assume we immediately put a watermelon of 8kg to the room at 2°C. Assuming a specific heat of 4200J/kg for the watermelon, how long will it take for the watermelon to reach room temperature of 20°C if we assume that heat pump only heats watermelon? O A) 2.7 minutes B) 3.2 minutes C) 4.4 minutes O D) 5.3 minutes E) 6.2 minutes COMP.
answer all with explanation
7) Outlet Temperature and Heat-Transfer Rate via Minimum Allowable Approach Temperature. Hot oil at a flow rate of 3.00 kg/s (Cp = 1.92 kJ/(kg-K)) enters an existing 1-1 counterflow exchanger at 400 K and is cooled by water entering at 325 K (under pressure) and flowing at a rate of 0.70 kg/s. The overall U = 350 W/(m².K) and A= 12.9 m². Calculate the heat-transfer rate and the exit oil temperature if the minimum allowable approach temperature is to be 10 °C (10 K).
The condensing pressure for a Rankine engine is 0.001325 MPavac. Calculate the following for steam flow rate = 16.3846 kg/sec of steam when the steam at the beginning of expansion is at 119.6 deg SH and 4.0 Mpaa. Draw the TS and equipment diagrams for the ideal and actual case and find for the following for the ideal case:
Determine the compressor work, W,comp. And the condenser heat transfer, Qc.
An air-cooled condenser has an expected U value of 30 based on the air-side area. The m²-k condenser is to transfer 60 kW with an airflow rate of 15 kg/s entering at 35°C. If the condensing temperature is to be 48°C, what is the required air-side area? Recall Cp,air = 1.0- kg-K kJ
A Rankine cycle is executed with steam expanding initially from 20 MPaa and 100 deg SH.Condensation occurs at T = 86.49 degree Celsius. All expansion and compression efficiencies are 90 %.Sketch the equipment layout and the TS diagram. Answer the following for (m = 10 + SN/10 ) kg/sec of steam circulated and fill up the blanks in theitems below:1. TS diagram with the cycle showing correct location of points with respect to saturation domeline with ne and nc = 90%.2. If the generator efficiency = 95%, brake engine efficiency = 90% what is the brake work in KW?Answer: ______________________3. Actual Steam Rate for the engine in Kg/KW-hr with efficiency values at item 2. Answer: _________________________
Find the thermal efficiency of the system in percentage to 2.d.p.
10. An adiabatic air compressor (does not exchange heat with the environment) has an efficiency of 40% and a power of 1.5 kW. This is used to compress 30 kg/h of air with atmospheric conditions (P=77 kPa, T = 298 K). The final pressure is 246.5 kPa. i. What is the initial specific volume and what is the final enthalpy of the air? J. What must be the volume of the tank to store the compressed air in 8 working hours of the compressor?