H.W Find the distance between Pins of type O and@ and the numbers ofthese Pins that Can be used in the longitudinal direction of the simply supRrtedover hanging beam shown in figure ? Knewing that the allowable shear Stress ofPin is 3.5 Ma,diameter of cach Pin is 12mm and IvA= 7.4*10 mmtype O.Ans/ S,=62.5mmSommtyre2SoKSompm(for one layor)Somm25mmNA-25MMNAAns/ S2=312.5mm2m2mSommSommNo.0=13(for one hju) SoMmNaty=2+67=134 (T8. layır)No. =2A13=26 (Two IAter)Somm1SommSomm

Answered: Image /qna-images/answer/2f641705-be52-4fcb-90ec-92e823ccf152.jpg

H.W Find the distance between Pins of type O and@ and the numbers of these Pins that Can be used in the longitudinal direction of the simply supRrted over hanging beam Shown In figure ? Knewing that the allouable shear Stress of Pin is 3.5 Ma,diameter of cach Pin is 12mm and IvA=7.4*10mm type O. Ans/ S,=62.5mm Somm tyre2 SoK Somm (for one layor) NA- Somm 25mm -NA Ans/S2=312.5mm 25MN 2m 2m Somm Somm No.0=13 (for one hju) SoMm Notj=2+67=134 (TR. layır) No. =2A13=26 (Two lAter) Somm 1Somm Somm

H.W Find the distance between Pins of type O and@ and the numbers of these Pins that Can be used in the longitudinal direction of the simply supRrted over hanging beam Shown In figure ? Knewing that the allouable shear Stress of Pin is 3.5 Ma,diameter of cach Pin is 12mm and IvA=7.4*10mm type O. Ans/ S,=62.5mm Somm tyre2 SoK Somm (for one layor) NA- Somm 25mm -NA Ans/S2=312.5mm 25MN 2m 2m Somm Somm No.0=13 (for one hju) SoMm Notj=2+67=134 (TR. layır) No. =2A13=26 (Two lAter) Somm 1Somm Somm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

pls reply
I need only handwritten And correct
Five plates with thickness t are bolted together by a bolt with diameter d. Which of the following gives the maximum bearing stress among all the plates? A.1.50 P/bt B.1.50 P/nd2 0.75P- C.0.75 P/bt 1.5P D.0.750 P/id2 0.75P- For the deformed plate shown in figure X, the magnitude of the shear strain at point D is nearest to 2 mm 5 mm A.0.229 rad B.0.004 rad C.0.573 rad D.0.010 rad 500 mm 500 mm Plates A and B are to be connected using bolts and two cover plates C and D as shown. The force exerted on plate A is 30 kN and the diameter of the bolts used is 25 mm. The thickness of all the plates is 15 mm. Which of the following is the shear stress experienced by either bolt? A.30.6 MPa F B.61.1 MPa B C.45.8 MPa D.15.3 MPa B
The cantilever beam shown below has the cross-section on the right portion. If the allowable stresses are 62 MPa shear and 103 MPa tension at point A (just below the flange), determine the maximum allowable load P.
Two circular shafts are joined together between fixed supports to resist a torsional moment of 80 kN-m as shown. Determine the absolute value of the maximum torsional shear stress of the hollow steel shaft (in MPa). 20 IN-m Sm stcel hellw circalar duminum Selid circular D= 75 mny Do- IDO mn D> 80 mm G- D GPon 6- IS0 EPa
b2 b1 750mm 150mm 150mm Consider the figure on the right. A steel 650mm plate is used to connect a member to a steel column. 5 - 32 mmø steel bolts are used as fasteners. 1. If P-10 kN determine the average shearing stress on the bolts.** 2. If the allowable shearing stress on the bolts is 200mm 60MPA, determine the maximum safe value of P.* Hint: Use the following formula to determine the centroid. 1 (b,? + b,? + b,b2) y = b, +b2 h (2b, + b2) 31b, + b2 CG
B2
Q2: aluminum rod AB (G 27GPA) brass rod BD (G = 39GPA). portion CD of the brass rod is hollow and has an inner diameter of 40 mm, Determine: a) the angle of twist at A. b) maximum shear stress of rod AD c) torque diagram d) angle of twist diagram
(N) 32900
The figure (all dimension are in mm) below shows an I-section of the beam. The shear stress at point P (very close to the bottom of the flange) is 12 MPa. The stress at point Q In the web (very close to the flange) is: N'-. 100- P Q 201 100- T 20 81484 80 20 40 --N (a) Indeterminable due to incomplete data (6) 60 MPa (c) 18 MPa (d) 12 MPa 068
Two circular shafts are joined together between fixed supports to resist a torsional moment of 80 kN-m as shown. Determine the absolute value of the maximum torsional shear stress of the hollow steel shaft in MPa. ( COMPLETE SOLUTION NO ROUNDING OFF)
hand written asap (solve all parts)