H. The force, F-(9i+15j+-31k) lb, is attached at the end of a bent pipe at point, (-32ft, 48ft, 86 ft) and the height of the vertical section is 35ft. Also, a moment, M-269ft-lb, is applied CCW around the z axis. What is the moment created around point A, report your answer in cartesian form. (x, y, z) Point A 1. The system shown has a pin at B and a cable connection from A and C. If the mass of the block, M-99kg, 0-64°, Height 3.9m, and Length - 5.2m. What is the tension in the cable? 4 Block X

H. The force, F-(9i+15j+-31k) lb, is attached at the end of a bent pipe at point, (-32ft, 48ft, 86 ft) and the height of the vertical section is 35ft. Also, a moment, M-269ft-lb, is applied CCW around the z axis. What is the moment created around point A, report your answer in cartesian form. (x, y, z) Point A 1. The system shown has a pin at B and a cable connection from A and C. If the mass of the block, M-99kg, 0-64°, Height 3.9m, and Length - 5.2m. What is the tension in the cable? 4 Block X

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Please answer complete question
I want to talks about this paragraph very briefly (pen heads)
Topic/s: Force System of a Force, Moment of a Force, Moment of a Force-Scalar Formulation,Moment of a Force-Vector Formulation, and Principle of Moment. Reminder: Kindly show the complete step-by-step solution. Please make sure that your handwriting is understandable and the picture of the solution is clear. I will rate you with “like/upvote” after. Thank you.
THIS IS NOT A COMPLETE QUESTION, IT JUST NEEDS TO HAVE THE STEPS IN THIS WAY. (PLEASE DON'T SEND ME A CHEGG ANSWER! I HAVE A CHEGG ACCOUNT. I SENT THIS QUESTION CHEGG AND I DON'T WANNA TAKE SAME ANSWER LIKE THAT! PLEASE JUST SOLVE ON YOURSELF OR LEAVE PLEASE. Fluid Mechanics question.)
PLEASE WRITE LEGIBLY, COMPLETE SOLUTIONS WITH DRAWING THANK YOU! A car weighing 9 kN travels at 80 km/hr. At the foot of an incline of 10%, the engine stops. Determine: a – acceleration. b – time for the car before it stops. c – distance traveled by the car before it stops.
please put it on paper. thank you
|Read the problem statement and the solution provided. There may or may not be one or more mistakes in the solution. Go through the solution carefully and then do the following. 1. State if the solution is correct or incorrect 2. If the solution is incorrect, identify what is the mistake in the solution. Be specific and succinct. 3. If the solution is incorrect, provide the final solution with appropriate steps. You can make the corrections directly on a copy of this provided solution, but make sure you clearly explain the corrections. Problem: Consider fully-developed flow of water through a 24-cm diameter tube. The water comes in at 20°C and exits at 40°C. The surface temperature of the tube is uniform at 60°C. The water flow has a mass flow rate of 0.24 kg/s. What is the average convection coefficient of the water flow? Solution: We have T, = 60°C, Tmi = 20°C, Tmo = 40°C, So, the bulk-mean temperature is Tm = 30°C. The appropriate properties are: u = 7.98 × 10-4 kg/ms; k = 0.615…
i need clear ans and solve very very fast in 20 min and thank you | DYBALA A part under forming force showed that 15% decrease in thickness and 10% increase in width, find the change in length (sign and value) if initial length is 200 mm?
Essay format: Write 3 paragraph(3-5 sentences each)or more on what are the challenges in engineering in thermal engines and thermodynamics cycles and add a conclusion in your own words of 5 sentences. Use a scientific article and cite where needed and list the name and author of article below. No PLAGIARISM! Please allow someone to assist that is willing to take the time and answer correctly, if written properly I will upvote. IF YOU WILL NOT HELP OR ATLEAST READ AND ANSWER PROPERLY THEN I WILL DOWN VOTE. SO PLEASE ALLOW SOMEONE TO HELP THAT IS WILLING.
Can some one please help to solve this question following the directions and showing neat work and formulas. PLEASE AND THANK YOU!!!
Summary/Conclusion Discuss the strengths of your design and how it met the specifications. Discuss your assumptions and why they are valid. Discuss what you might change about your design in a redesign effort. Format: The project should be presented as a design report using a word processor. Include any hand calculations in an appendix. More details will be provided. Choose to design either a slip-jaw or channel-lock pliers to last for 25 years of use by a professional. Use an appropriate tool steel for the pliers. Design for 95% male grip force. Use a minimum factory of safety of 2.50. Determine dimensions not given. Slip Jaw Pliers A= 9.00 inches B=1.00 inches C= ? D=1.25 inches H= 1.875 Inches D B A
Oz Lawn Care Inc. manufactures and assembles lawnmowers that are shipped to dealers throughout the United States and Canada. Two different procedures have been proposed for mounting the engine on the frame of the lawnmower. PB (Minutes) UPB (Minutes )345798632 5 Is there a difference in the methods' mean time to mount the engines on the frames of the lawnmowers? The answer must be in handwriting. Please write your answer using a ball - point pen on plain paper. Submit your homework by uploading it to the canvas. Good Luck!