Given the state of in situ stress below 15 0 lo] = 0 40 in MPa 0 0 Where z axis is vertical and xy is the plane of horizontal stresses: a) state what type of fault is expected to be observed here. ) sketch and indicate the principal stresses on the Mohr circles representing fault failure. ) if the friction angle between the surfaces of the fault is 20° show or give the angle between the plane of the fault and y axis.

Given the state of in situ stress below 15 0 lo] = 0 40 in MPa 0 0 Where z axis is vertical and xy is the plane of horizontal stresses: a) state what type of fault is expected to be observed here. ) sketch and indicate the principal stresses on the Mohr circles representing fault failure. ) if the friction angle between the surfaces of the fault is 20° show or give the angle between the plane of the fault and y axis.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The location of trial failure surface on a slope is shown in Figure and the stress components for each slice are listed in Table. Slice Shearing component _(kN.m·') -0.280 -0.227 0.383 3.214 6.543 8.368 9.792 Normal component (kŇ.m*) 1.911 7.745 13.139 16.344 17.625 16.718 12.125 0.486 Length of trial failure surface=11m Soil friction angle 6° Cohesion, c=28kPa No. 1 3 4 6. 4.228 Trial Fallure Surface (a) Compute the driving stress. (b) Compute the stabilizing stress. (c) Analyze the safety of the slope.
[?] ?? = [150 −60−60 −180]➢ Determine and graph using Mohr's circle the principal stresses and theaddresses associated with these.➢ Determine and graph the maximum shear stresses.➢ Plot the possible failure planes.➢ Finally, what is the value of the maximum tangential stress and at whatorientations take place?
Stresses in Soil Mass: Mohr's Circle 131.6 kPa 53.6 kPa 315.2 kPa 315.2 kPa 35 131.6 kPa 2. Find Normal and Shear Stress at Failure Plan A-B. Enter your answer to three significant figures. (1 decimal place)
7. 4) Determine the increase in vertical stress at a depth (2) m belowpoint A due to surface loads shown in Figure (2). m or n L.O 10.0 9.0 8.0 7.0 6.0 5.0 4.0 E 3.0 2.5 2.0 G.S.L xxxx 1.5 z 1.5 -0.006- -0.007 0.006 0.009 0.15 19 -0.011 0.010 Section b-b 2 160 kPa 0.2 0.012 0.014 m or n 2.5 3 G014 0.016 0.020 & 0.25 0.3 0,024 120 kPa 4 2.000 0.4 5 -0.04 6 0.06 S b + 7 8 9 10 0.13 ats 0.34 0.5 0.6 0.7 0.8 0.9 1.0 m or n (a) 2.5 m 160 kPa 120 kPa ais. 1.5 . 1.5 2 2.5 3 2.5 T 3 1.5 m 2 m 0.5 m 4 4 5 Fig.(2) 6 7 8 9 . 1 10 11.0 0.9 0.8 0.7 0.6 40.5 10.4 0.3 0.25 0.2 m of n E 0.15 0.10 .9 10
The location of trial failure surface on a slope is shown in Figure and the stress components for each slice are listed in Table. Slice Shearing component (kN.m') -0.280 -0.227 0.383 3.214 6.543 8.368 9.792 Normal Length of trial failure surface=11m Soil friction angle 6° Cohesion, c=28kPa No. component (kN.m') 1.911 7.745 13.139 1 2 4 16.344 17.625 16.718 12.125 7 8. 4.228 0.486 Trial Failure Surface (a) Compute the driving stress. (b) Compute the stabilizing stress. (c) Analyze the safety of the slope.
Ludraulic fracture was initiated in a borehole at a depth of 3001 Problems sume the normal faulting is recent. tad continuously from the surf
Show shear stress variation over rectangular section of RCC.
6.5 Compare the movement of normal and reverse faults. What type of force produces each? 6.6 Contrast between the following: a- Stratification and bedding.
1. Maximum Principal Stress 2. Minimum Principal Stress 3. Maximum Shear Stress 4. Normal Stress at Failure Plane A-B 5. Shear Stress at Failure Plane A-B ... 181.6 kPa 53.6 kPa 315.2 kPa 315.2 kPa 131.6 kPa Mohr's Circle Sign Conventions: ... •Compressive normal stresses are positive •Shear stresses are positive, if when they act on two opposing faces, they tend to produce a counterclockwise rotation.
Q.9 A plate of area 2m² on which fluid flow with 2y² Y velocity profile as "= 7 5'where y(m) is distance from plate, u(m/s) calculate shear stress (N/m²) at y = 0.4m from plate, when flow is laminar. Dynamic viscosity = 0.015 Pa-s
A point within an embankment slope has a vertical normal stress (v) of 100 kPa, a horizontal normal stress (x) of60 kPa, and a horizontal shear stress (xy) of 20 kPa.(a) Determine the major and minor principal stresses.(b) Determine the orientation of the major principal stress (in degrees from vertical, clockwise, orcounterclockwise.(c) Draw the Mohr Circle and schematic of the element stress state
Figure 3 shows the stresses at failure for a point in a soil mass. Note A.U. (a) Draw the Mohr Circle for this point. (b) Determine the Pole Location. (c) Determine 01 and 03. (d) If the soil cohesion, c = 1.0, what is the friction angle of the soil, o? (e) Determine Tƒƒ and off. (f) What are the orientation of the failure planes, cr? 2 3 5 20° 51°