Given the section and plan view of the structural elements (Foundation and Column), estimate the concrete material quantities to be used in construction. There are sixteen (16) - C3F2 in the entire structure. Consider only from the foundation base up to the Natural Ground Level (NGL). The concrete is to have a minimum compressive strength of 3500 psi (24 Mpa). Determine total bags of cement, total volume of fine aggregates and total volume of coarse aggregate.

Given the section and plan view of the structural elements (Foundation and Column), estimate the concrete material quantities to be used in construction. There are sixteen (16) - C3F2 in the entire structure. Consider only from the foundation base up to the Natural Ground Level (NGL). The concrete is to have a minimum compressive strength of 3500 psi (24 Mpa). Determine total bags of cement, total volume of fine aggregates and total volume of coarse aggregate.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Calculate the Flexural strength (Modulus of rupture) of concrete of 4"x 4"x12" beam tested 4500 lbs (total load) in flexure at 3rd points (The supports are located at 1.5 inches from the edges on either side) Please carry out calculations up to two decimal places. 126 Psi 570.63 Psi None of the above 632.81 Psi
Determine the development length required in bar diameter for the epoxy-coated bottom bars of the beam with 4 - 25mmΦ longitudinal bars annd 10mm stirrups @ 200mm o.c., bw = 400mm, side and bottom cover = 80mm, spacing between bars is 80mm o.c., normal concrete with f'c = 21 MPa, fy = 420 MPa. Consider Ktr in calculation. Express your answer in whole number.
/hvp/view.php?id%3D17809 eStructures (Lecture 4, Part 2). Derivat The concrete is assumed to crush at a strain of about If we sub value prey pf d 0 85f equate oM expression O 0.02 0.03 0.003 Check
Generally, compressive strength normally considersin all stages in our designs. Explain and state other engineering strength that neededto be taken care of in the process of design. Comment on how it affectsreinforce concrete structure.
3. The clear spacing of the main longitudinal reinforcements in mm. A. 140.6 B. 155.3 C. 165.7 D.207.6
What is the shear force to be carried by the reinforcements of a beam subjected to axial tension if it has a width of 313 mm and an over-all depth of 477 mm? The specified compressive lightweight concrete is 22.2 MPa and the yield strength of stirrups is 333 MPa. The distance of tension reinforcements from the outer fiber of the beam is 59 mm. Round off your final answer in 3 decimal places. Loadings: VDL = 72 kN %3D VLL = 62 kN Axial Tension (DL) = 90 kN Axial Tension (LL) = 19 kN
#5 sp.gr of concrete is 2.4
Give full explanation Awall form 14 ft high is filled with 160 lb per cu ft concrete at a tem perature of 70°F. The concrete is Type I without a retarder. Concrete will be placed with normal internal vibration to a depth of less than 4 ft. The rate of placement is 5 ft per hr. From Table 1, the value of Cw is 1.1 and from Table 2 the value of Cc is 1.0. The rate of placement is less than 7 ft per hr and the place ment height does not exceed 14 ft so calculate the lateral pressure by using appropriate formula.
Determine the tensile development length required for the uncoated #8 bars shown if normal weight concrete and 180° hooks are used. f'c = 4000 psi and fy = 60000 psi. 21"- 3 @ 5" 3" = 15" 4 #8 #3 stirrups @ 6" O.C. 27 30
For pretensioned axially tensioned member, how to calculate the effective prestress established in the concrete? How to calculate the destressing load, cracking load and ultimate load, respectively, in the loading stage? Write the calculation equations.
The modulus of elasticity of a normal concrete with f'c = 28MPa and density of 2350kg/m3 is nearest whole number. Blank 1 Blank 1 Add your answer GPa. Round of to the
The loadsshown on the beam with a cross section at midspan as shown, are service (unfactored)loads. The concrete used is a normal weight concrete with compressive strength of 4000 psi.The yield strength of the reinforcement is 60,000psi. For the midspan section shown, computeφMn and show that it exceeds Mu