Given the parabola 3x2 + 40y – 4800 = 0. (a) What is the area bounded by the parabola and the x-axis? (b) What is the  moment of inertia, about the X-axis, of the area bounded by the parabola and the X-axis? (c) What is the radius of gyration,  about the area bounded by the parabola and the X-axis?

Q: Q3/ What should be the value of a which will make the motion of 900 N blocks down the plane to…

A: Step 1:Step 2:

Q: The collar is designed to fit loosely around a fixed shaft with a radius of 2 in. Determine the…

A: Radius of Shaft = 2in Coefficient of kinetic friction = μk Radius measured from center of collar to…

Q: Two rods are connected by a slider block as shown. Given: Mg= 250 lb-in. MA MB 15 in. 25° |A -15…

A: Draw the free body diagram.

Q: 900N/m В C 3m 4m 2m OD А

A: since roller at D  horizontal force will be zero at A and D

Q: Determine the speed at which the basketball at A must be thrown at the angle of 30° so that it makes…

A:

Q: Determine the moment of inertia with respect to the x axis for the circular area shown.

A: The given section:

Q: Kinematical equation is given as: 1 y yo = uoyt + ayt² .. (1) where, y and yo is the final and…

A:

Q: If a force of P = 30 N is applied to the handle of the lever, determine the largest couple moment M…

A: Given: The coefficient of static friction is 0.3. Force P is 30 N. Calculation: The figure is shown…

Q: A flat plate is placed normal to a discharging jet of water. The jet discharges water at the rate of…

A: Given- Rate of discharge from jet Q= 0.2 m3/s, Speed of water V= 18 m/s, It is needed to find the…

Q: 9. A solid spherical steel ball of radius 6 cm is placed inside a 20- cm diameter cylinder…

A: Ans 9) Given  steel ball radius, r = 6cm cylinder diameter = 20cm    depth of water in cylinder =…

Q: A cylindrical barrel of diameter D and mass m (when empty) is filled with water to an initial height…

A: The direction and magnitude of the force vary from time to time due to the different reactions…

Q: The 0.8-Mg car travels over the hill having the shape of a parabola. When the car is at point A, it…

A:

Q: the pu Calculate the moment of inertia with respect to the z-axis of the thin surface shell of…

A:

Q: Determine the moment of inertia about x' axis and x axis. 200 mm 不 1 lomm 29 K A20k

A: The given data: length of section, L=200 mm height of section, H=20 mm (as you have shown in figure)…

Q: Subject: Statics of Rigid Bodies Complete answer and clear hand writing Dont forget the free body…

A:

Q: Locate the mass center of the homogeneous solid body whose volume is determined by revolving the…

A:

Q: 50 rpm 1000 mm 300 mm 3. Determine the centroidal moment of inertia about the X axis.

A:

Q: The speed of the brake drum shown is controlled by a belt attached to the control bar AD. A force P…

A: We have to fnd out the magnitude of the couple being applied to the drum.

Q: 0.24m 0. Im B 0.08m D 0.06m

A: Given data: wAB=10 k rad/sr⇀BA=-0.06i+0.08j mr⇀CB=0.24i+0.1j mr⇀DC=-0.18j m a) calculating velocity…

Q: Ex: A Torque (T) is applied to a solid taper shaft with built-in ends, as shown in Figure, Determine…

A:

Q: *54. A heavy flywheel rotates at an angular speed w (radians per second) around an axle (see…

A:

Q: P 300 mm 300 mm B 150 mm 200 mm A P (N) 500 t (s) 2 The 47-disk is rotation at 151 rad/s. The force…

A: Mass of disk=47kg Rotation=151rad/sec

Q: 360 mm 80 mm 130 mm 130 mm 300 mm 90 mm 280 mm

A: The FBD of the beam will be:

Q: The rotor of an electric motor rotates at the constant rate 1 w₁ =1800 rpm. Determine the angular…

A:

Q: A crane lifts a load from ground level. The height, s m, of the lift at time t seconds is given by s…

A: We are given  a relation between the time(t) and height(s) in the form of s=3t250-t3250 which is…

Q: Find the the Gradient of (f(Zy-3)) * -3i+zj+yk O zj+yk O -3 ( itj+k) A body falls from rest in the…

A:

Q: PROBLEM 5: Determine the moment of inertia with respect to the centroidal X and Y axes. Yo 1" -…

A: Given I - section shape with dimensions and thickness. To Determine   Moment of Inertia with respect…

Q: 2. Determine the centroidal moment of inertia about horizontal and vertical axes. Use 3 decimal…

A:

Q: When the mechanism is released from rest in the position where 0 = 40°, the 6.9-kg carriage drops…

A: A pivot point is a technical analysis indicator, or calculations, used to determine the overall…

Q: 75mm 25 mm 150 mm 25 mm 25 mm 125 mm

A:

Q: QUESTION 4 A 0.5-mm-diameter glass tube is inserted into water at 20°C in a cup. The surface tension…

A:

Q: 500 mm 100 mm 500 mm 400 mm 50 mm 1. Determine the centroidal moment of inertia about X and Y axis.

A: Determine centroidal moment of inertia about X and Y axis

Q: V₂ = 12 units Iz V₁ = 10 units 60° Find the magnitude of the vector difference V = V₂ - V₁ and the…

A: Given figure:

Q: A 3-kg disk A is mounted on arm BC, which has a negligible mass. A torque of M (5e0.5t) N-m, where t…

A: Given data:- The given disk weight is, w=3 kg The given thickness of the disk, t=60 mm The given…

Length and Length related Variables

Length can de defined as the measurement or extent of physical quantities or objects from one terminal to another terminal. Stone age humans used finger length, step length, and so on to measure the size or displacement of an object. Nowadays, depending on how precise the measurement requires to be and the object’s size is measured, we use measuring devices for measurements like rulers and steel tape. Most people have used a ruler or tape measure to measure a particular distance or the size of an object. For more precise measurements of tiny objects, the development of measurement tools such as the Vernier caliper, which permits us to measure dimensions within 1/1000 of an inch. In the last few decades, electronic distance measuring instruments (EDMI) have been implemented that permit us to measure distances from a few feet to many miles with reasonable accuracy.