Given the following truth-table describing a boolean function F(X,Y,Z). X Y ZF Synthesize the combinational function with two functionally equivalent o 0 0 1 networks: the first one realized as sum of products (AND-OR) and the o 0 1 0 second one as product of sums (OR-AND). To verify the equivalence of the o 1 0 1 two networks, draw them in the d-DcS. Perform a timing simulation of the 0 1 1 two nets, including all possible combinations of the inputs X, Y and Z (a 1 0 0 0 10 1 1 1 1 |0 1 1 |1 0 suitable test sequence is available in the Timing Diagram window). 1

Given the following truth-table describing a boolean function F(X,Y,Z). X Y ZF Synthesize the combinational function with two functionally equivalent o 0 0 1 networks: the first one realized as sum of products (AND-OR) and the o 0 1 0 second one as product of sums (OR-AND). To verify the equivalence of the o 1 0 1 two networks, draw them in the d-DcS. Perform a timing simulation of the 0 1 1 two nets, including all possible combinations of the inputs X, Y and Z (a 1 0 0 0 10 1 1 1 1 |0 1 1 |1 0 suitable test sequence is available in the Timing Diagram window). 1

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

(B): Design a Moore FSM to detect the sequence (00) using T-FFs. Q4/ (A): Design a Mealy FSM for odd parity generator using JK-FFs.
Q7) How many unused combinations are there in the representation of BCD numbers using 7-4-2-1 weighted scheme? What are they?
Implement the given Boolean function F(A,B,C,D) = m (0,3,6,8,10,11,12,14,15) using a multiplexer with ACD as select lines. Use block diagram for your multiplexer and label properly. 1. What must be connected to select line S₁? A) A B) B C) C 2. What must be connected to select line S2?? A) A B) B C) C 3. What must be connected to input lo? A) B' B) B 4. What must be connected to input 11? A) B' B) B 5. What must be connected to input 12? A) B' B) B 6. What must be connected to input 15? A) B' B) B 7. What must be connected to input 17? A) B' B) B 8. What size of the decoder should be used? A) 2x1 MUX B) 4x1 MUX C) 1 C) 1 C) 1 C) 1 C) 1 C) 8x1 MUX D) D D) D D) 0 D) 0 D) 0 D) 0 D) 0 D) 16x1 MUX
Implement the following Boolean function using a multiplexer. Use A, C and D as the select lines, where A is the MSB, and D is the LSB. F(A,B, C, D) = > (1,3,4,8,9,11,12,15) Which of the following inputs are not connected to the ground? A. 1o В. 12 C. 15 D. More than one of the choices E. None Which of the following inputs are connected to the complement of B? А. 1o В. 14 С. I7 D. More than one of the choices E. None
2) Design a 2-to-1 multiplexer in which the inputs and outputs consist of single bits. Provide the truth table for this multiplexer using IN0 and IN1 for the two inputs, S for the select line and OUT for the output correctly. Obtain the minimal standard sum-of-products expression for the output correctly. PS: Please answer Number 3 from or after number 2 3) Obtain the schematic diagram for the mux designed in 2). Use proper conventions as to the labelling of part numbers, instance numbers and pin numbers correctly.
2 QUESTIONS ONLY. a) Using the K- Map simplify the following standard SOP expression X Em (2, 3, 5, 6, 7, 8, 9, 12, 13, 15) and find the simplified expression for X (3 marks) b) Implement the above simplified expression using gates. (1 mark) c) Write the standard POS expression for X given in part (a), as a function of input variables (A, B, C... (1 marks) d) Briefly explain Applications of DACS? (2marks)
To display the hexademical value of a 4- bit number on a 7-segement display. the LEDs of the seven segment compnent are lit with a logical "0" (actice low). The inputs are (active high). a) complete the below truth tablee for each output b) Using Karnaugh map provide the simplifed expession for each output(a,b,c,d)
Implement the following Boolean function using a multiplexer. Use A, C and D as the select lines, where A is the MSB, and D is the LSB. F(A, B, C, D) = > = >. (1,3,4,8,9,11,12,15) What is the output when A=1, B=0, C=1 and D=0? A. +5V В. OV С. В' D. More than one of the choices E. None What is the output when A=0, B=1, C=0 and D=0? А. +5V В. OV С. В D. More than one of the choices E. None
Task 2:For the function F(A,B,C) = (1,2,3)A. Write the truth table.B. Find the simple/simplest version by using K-Map consideringthe POS.C. Draw the circuit diagram by using JUST NOR GATES (you can useNOT itself.D. Define the input variables by considering that MSB’s frequencyis 2 Hz.E. Simulate the circuit you found in C. Explain the results.
For the function F(A,B,C) = (1,2,3)A. Write the truth table.B. Find the simple/simplest version by using K-Map consideringthe POS.C. Draw the circuit diagram by using JUST NOR GATES (you can useNOT itself.D. Define the input variables by considering that MSB’s frequencyis 2 Hz.E. Simulate the circuit you found in C. Explain the results.
b Q1. 1-az-1 Obtain round off noise variances of given system. Fixed point arithmetics is used for both Direct form I and Direct form II. Explain how a and b coefficents effected.
If the given Boolean function below is expressed in SOP, list all the essential prime implicants. Show the necessary maps to support your answer. Clearly identify and label all groups on the map. Show map grid lines. f(A,B,C,D,E) = Em(0, 1, 4, 5, 10, 11, 14, 15, 16,17, 21,25, 26, 29, 30) Essential prime Implicants =