Given the following transfer function, where time is measured in seconds: X(s) F(s) The natural frequency for this system is: a) √16 rad/s b) √24/8 rad/s f) none of the above = 2 2s² +8s + 24 c) √4 rad/s d) √8 rad/s e) √12 rad/s If a second order system has the following characteristic roots: -2 and + 3, its free response will be: a) Oscillatory and stable b) Non-oscillatory and stable c) Oscillatory and divergent d) Non-oscillatory and divergent e) Oscillatory and neutrally stable f) none of the above

Given the following transfer function, where time is measured in seconds: X(s) F(s) The natural frequency for this system is: a) √16 rad/s b) √24/8 rad/s f) none of the above = 2 2s² +8s + 24 c) √4 rad/s d) √8 rad/s e) √12 rad/s If a second order system has the following characteristic roots: -2 and + 3, its free response will be: a) Oscillatory and stable b) Non-oscillatory and stable c) Oscillatory and divergent d) Non-oscillatory and divergent e) Oscillatory and neutrally stable f) none of the above

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter23: Resistive-inductive-capacitive Series Circuits

Section: Chapter Questions

Problem 1PA: You are an electrician working in a plant. A series resonant circuit is to be used to produce a high...

See similar textbooks

Similar questions

The positive values of "K" and "a" so that the system shown in the figure below oscillates at a frequency of 2 rad/sec respectively are K(s+ 1) R (s)- C(s) (s + as? + 2s + 1) O 1,0.75 O 1,0.66 2,0.66 2,0.75
How many corner frequencies are in the following sinusoidal transfer function? 10(jw + 100) (jw + 1) 17 - G(jw) = O A) There are not correct answers B) four C) three O D) five E) two
A coutimuous-time sinusoid has frequency 2 = 70r rads sec and is sampled at a sampling interval of T=0.01 sec. What is the frequency of the discrete-time sinusoid? %3D Oa =70z rads ses OL- 0.7z rada sec Oce= 7x rads sec Od0= 7000r ads see
Q9 Given that you have found the following transfer function for a circuit, H(jw), what is the magnitude at very high frequencies? (If your answer contains w, you may simply type "w" instead.) J (jw): 0 jwRC (1-w²LC)+jwRC Save Answer Las 010 Given that you have found the following transfer function for a circuit, H(jw), what is the phase (in radians) at very low frequencies? (If you answer contains π, you may simply type "pi" instead) pi/2-tan^-1(wRC/(1-(w^2)*LC) Save Answer Lá
21) Looking at the following circuit, select the correct Transfer fucntion. Please recognize that the answers are expressed in rectangular coordinates and not in magnitude, making this an easy problem. 21). ww w For the circuit in the given figure, assume L = 0.5 H and R= 200 kohm. ele O Vout (jw) Vin (jw) 200 k Vin R Vout –200 k+jw0.5 Vout (jw) ju0.5 200 k- jw0.5 Vin (jw) O Vout (ju) Vin (jw) - jw0.5 200 k– jw0.5 Vout (jw) 200 k Vin (jw) 200 k+jw0.5
DTFT is a continuous function in frequency domain DFT is a discrete function in frequency domain O Yes O No
A 100 Hz sinusoid is sampled at thrice the nyquist rate. Then how many samples are obtained in 2sec.
For the parabola input of the closed loop system given below, the steady state error is ess = 0.001 Gc What should be the transfer function of the block?A=23B=432X=46B=216
Find transfer function Eo(s)/Ei(s) Do it my complex impediance method and show diagram Provide right and complete answer do each steps with loops
Find the magnitude, phase and impulse response from the following frequency response (eju) = 4e-j4w sin sin() w
For the circuit shown, Vin (w) is a sinusoidal voltage with amplitude Vo. Think of this circuit in terms of a voltage divider in answering the following questions. Vin sine ww R C R Vout (a) Without doing any complicated analysis, explain how the output amplitude behaves as w → 0 and w → ∞. (b) What is the ratio Vout (w)/Vin (w)|? (c) What is the phase of the output (relative to the input) as a function of w?
In an audio signal processing and chord detection algorithm, the following signals are used as test signals. Check whether the signals are periodic or not. It is periodic, find the fundamental time period N (a) x(n) = sin2nn + sin6an (b) x(n) = en (c) x(n) = sin ()n