Given the following properties of T-beams. If the beam is reinforced in tension only, determine (a) the balanced steel area (b) the nominal and ultimate balanced moment capacity (c) the maximum steel area (d) the nominal and ultimate maximum moment capacity Flange width, bf = 1200 mm Flange thickness, t = 125 mm Width of web, bw = 300 mm Concrete strength, f'c = 28 MPa Steel strength, fy = 414 MPa Effective depth, d = 465 mm

Q: WATER A 8 = 9810 N/m2 he hg = 3m ho - 10 m ho l=9.4m CP 2=45° Wzim D FIND: ? Ya %3D

A:

Q: The ship has a length of 180m and a draught of 6.5m at station 2 while she is traveling with a speed…

A:

Q: Determine the volume of the lake shown below. Contour interval is 5 meters. The areas bounded by…

A: Given data- A contour is given as shown- Contour Interval (D) = 5 m To Find- The volume of the…

Q: 10. In similitude, Fapplication=Fmodel*3.44 a) True b) False

A: Answer: a Explanation: A model test was normally conducted to determine this particular relation.…

Q: Why do we need to find the Specific Gravity and Absorption of Fine Aggregate, Surface Moisture of…

A: Introduction:- Engineers value specific gravity because it assists them in establishing the…

Q: Draw the Y and M 6m 15 31² diagram 20 kN/m 6M 3j+c 20 amer= so kn эм

A: Given: A frame  Required: Shear force and bending moment diagram

Q: Problem 2 Angles AOB, BOC, and COD are measured on the same angle at point O. Determine the most…

A:

Q: 1. Determine the net area (A, ) for the angle given in figure below if 24 mm diameter holes are used…

A:

Q: 1. Byusing Area Moment Method, Determinethedeflectionatthemidspanofthebeamshown. 30 kN/m A B 5 m- -2…

A:

Q: he wireframe below shows each of the sequences, relationships, and durations of the activities. It…

A: where D = Duration ES = Earliest start EC Earliest close LS = Latest start LC= Latest close

Q: Find the total volume of the earth to be excavated up to elevation 5m. (red-elevation, blue=grid…

A: To find the total volume of earth to be excavated till an elevation of 5m

Q: Situation 3] From the measured value of distance XY, the following trials were recorded: Trials…

A:

Q: Consider the data below in the range 0.4 sxs1.2 0.4 5.1600 1.4 3.3886 2.2 5.7491 0.6 3.6933 1.6…

A:

Q: What inputs and outputs does a life cycle analysis (LCA) of a material consider?

A: When designing a life cycle analysis (LCA), it is really important that it clearly defines the input…

Q: T-30 = Cekt T = Cekt + 30 T(10) = 0°F: 0 Ce¹0k + 30 (1) = T(20) = 15°F: = 15 Ce 20k + 30 (2) k =…

A:

Q: How to get the 0.716N (from the underlined value on the picture)?

A:

Q: Given the data of an open traverse below, convert it into figure and determine its corresponding…

A:

Q: The data in the table below is for a closed-polygon traverse. Course Azimuth Length (m) Interior…

A: The data in the table below s for a closed-polygon traverse. Course| Azimuth [Length (m)| Interior…

Q: 20kn/m ೧.೧೯ (79 16.25km ೨೧ 30 d 35315 202250 Sokulm 16.25m/m But m 942 -Tom/m 10 ನನ್ನ 5) "↓ 3) 2331…

A:

Q: B) RA =, KN, R = KN/m 60 KN/m 55KN 175 KN A 6.00 m R 1.50 m 4.00 m

A:

Q: Q. 4 A = 500 , Pressure diff: b/w too limbs can be measured by measurement on Bne limb Then findl he…

A: A=500a To find error induced in measurement

Q: Complete the table. Show the figure and solutions necessary for the computation of the missing…

A:

Q: QSTRUC2

A:

Q: 7. Determine the best site using center of gravity technique Pasig Taguig Mandaluyong Makati Pasay…

A:

Q: 75m Find: AB = BC CA = 7.5m 7.5м в Jy member с узоки 60KN

A:

Q: 3 (b) There are five rain gauge sections viz. P, Q, R, S, T. Thei'ssen polygon network details are…

A: Given data: Rain gauge station P Q R S T Area (%) 24 21 37 8 10 Rain fall (mm) 45 57 65 67 78…

Q: A) RA=, KN, RB = KN 50 KN 20 KN/m 75 KN 15 KN/m 1m 1m A В 3.00 m 1 m 1m

A:

Q: Experimental, Values, N Trials Computed Values, N Percent Error RA .6659kg 6.5258 N 6.5333 N 0.11…

A:

Q: From the measured values of distance AB, the following trials were recorded. TRIALS DISTAN CE (m) 1…

A:

Q: Length (m) Observed Bearings Computed Sta Internal Angle Adjusted Values Corr Interior Line Forward…

A: Given,

Q: If weight of angles A & B is a AABC is W, the ratio of weight of angle C to weight of A is (a) 1 - 8…

A:

Q: -Deri ve P trapezoid - How wOL Q = - AR

A: Given data: trapezoidal channel:

Connections

In steel structures, connections are the members that join two or more steel members. The connections are the most important members of any steel structure, and hence, they are designed more carefully. The majority of the construction cost of steel structures is incurred due to the connections. The design of connections is done as per the recommendations and specifications of the American Institute of Steel Construction (AISC).