Given the following experimental data collected, what is the approximate torque of this motor at peak efficiency? LoadRotational Torque Mechancial ElectricalPower (W) Power (W)LoadEfficiencyMass (kg) Force (N) Speed (rad/s) (Nm)0.740.748.90.00740.0720.360.200.1741.728.30.01720.1440.480.300.2742.77.50.02700.2100.620.340.3743.6870.03680.2600.730.350.5745.645.80.05640.32010.320.7747.64.20.07600.3201.270.25

Answered: Image /qna-images/answer/bfb8ca43-e6c0-47b2-aeb8-07a4ba9b9a41.jpg

Answered: Given the following experimental data…

Engineering

Mechanical Engineering

Given the following experimental data collected, what is the approximate torque of this motor at peak efficiency?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Read the peak power and peak torque from the following curve. Also, find the engine speed that the peak power and peak torque occur at, and ensure this engine speed is in Rad/sec. Torque Power N.m kW 40 35 30 25 8020 70 6015 50 40 10 30 20 5 10 00 0 1000 N (C max) N(C min) N (Pmax) 2000 3000 4000 5000 6000 Engine Speed (RPM) g/kWh 400 300 200 100 0 Specific Fuel Consumption
Q.1 a. Repeatability and reproducibility are ways of measuring precision, particularly in the field of engineering. i. What is an engineer's expectation when performing repeatability or reproducibility? ii. State a difference between repeatability and reproducibility in an experiment? b. Figure Q.1 shows the measurement data of two types of thermal transducers namely thermocouple. Турe E Туре К 6.8 4.2 20 40 60 80 100 Temperature Difference (°C) Voltage Output (mV)
5) Which statement is true about the friction factor in the Moody diagram (shown below). Moody Diagram 0.1 0.09 Transition Region 0.08 0.07 0.05 0.04 0,06 0.03 0.05 0.02 0.04 0.015 0.01 0.03 0.005 0.002 0.001 5x10-4 2x10-49 10-4 5x10-5 10-5 5x10-6 10-6 Friction Factor 12---- Laminar Flow 64 Material Concrete, coarse 0.25 0.025 Concrete, new smooth Drawn tubing 0.0025 Glass, Plastic Perspex 0.0025 Iron, cast 0.15 Sevens, old 3.0 0.1 Steel, mortar lined Steel, rusted 0.5 Stoel, structural or forgod 0.025 Water mains, old Friction Factor=AP. 1.0 Smooth Pipe 3000 10³ 10¹ 105 106 107 108 Reynolds Number, Re - Vd P a) The lines for different relative roughness in the turbulent regime correspond to Darcy-Weisbach model b) The lines for different relative roughness in the turbulent regime correspond to Nikuradse model c) The lines for different relative roughness in the turbulent regime correspond to Hazen-Williams model d) The lines for different relative roughness in the turbulent regime…
1) An electric motor’s torque is a function of the speed at which it rotates. Many brushed AC motors have a linear toque curve as shown below. If the power output of the motor is equal to the torque (T) multiplied by the rotational speed in rad/s (w), what is the maximum power you can get out of the motor if the stall torque (Tstall) is 0.001 Nm and the no load speed (wno load) of 10,500 RPM? Give answer in Watts.
zain 10 2G 3G zain IQ Z Questions of Lectu... -> Questions of Lecture Five: Q1)) Define the following: 1) The stress & the strain 2) Mechanical stress and mechanical strain 3) yield strength and tensile strength 4) Modulus ofelasticity and the strain hardening Q2)) Fill the following blanks: 1)) Tensile tests are used to 3)) The most application tests of applied static stresses to which materials can be subjected are ---------, ---------, --------- 4)) Tensile stresses cause ---------, and compressive stresses ----------, while shear stresses ----------, of the material. 5)) Engineering stress-strain is important in ----------, while the true stress-strain is important in ---------- 6)) The unit of mechanical stress is --------- or ----------, while the unit of strain is n compression test, when specimen is compressed, its height is ---------, and its cross-sectional area is 8)) Compression is in contrast to the tensile, the compression test contributes to the ----------, in stress…
A force F=10i+13j-12k act at a point O, which is the origin. The magnitude and direction of the force is 1) 20.32 Units (0,=60.5 deg, 0,=52.2 deg, 0,=126.2 deg) 2) 40.32 Units (0,=60.5 deg, 0,=52.2 deg, 0,=126.2 deg) |3D 3) 10.32 Units (e=60.5 deg, 0,=52.2 deg, 0,=126.2 deg) 4) 0
Differantial Equations
Problem Solving: )An object falls from rest in a medium offering a resistonce. The velocity of the object hefore the ohject reaches the ground is given by the differential egua- tion dv/t + V% = 32, t/sec. uhat is the veloaty of the okject one second after it falls ?
1- Select the optimum choice for: high speed air craft skins material. Table 1: The properties of metallic materials E, GPa Max. use lemp, 'C | Density, Mg/cm' ay, MPa | Relative cost per unit sheet area Material 2.8 300 2 Aluminum alloy 200 69 200 7,8 350 350 700 Carbon steel Stainless steel 193 7.8 650 6 8.9 600 6 Nickel alloy Titanium alloy 207 1000 116 600 4.5 900 10 Table 2: Weighting factor Specific yield strength: Max, use temperature: Youngs modulus: 4 2
C Dynamic Analysis and Aeroelasticity SECTION B Answer TWO questions from this section ENG2012-N The moment of inertia of a helicopter's rotor is 320kg. m². The rotor starts from rest and at t = 0, the pilot begins by advancing the throttle so that the torque exerted on the rotor by the engine (in N.m) is modelled by as a function of time (in seconds) by T = 250t. a) How long does it take the rotor to turn ten revolutions? b) What is the rotor's angular velocity (in RPM) when it has turned ten revolutions?
MECT361 Mechatronics Components and Instrumentation Please solve the problem in keupord 0.Consider the Material Selection Design Problem for the FRAME of a Human Powered Road Vehicle. Define the selection criteria, assign weights (importance), and evaluate the following alternatives based on COST, WEIGHT, STRENGTH, AVAILABILITY, MANUFACTURABILITY, ASSEMBLY, TEST & MAINTENANCE, ENVIRONMENT & SUSTAINABILITY, SAFETY & RELIABILITY: a.Steel b.Aluminum c. Titanium d.Composite- CFRP
An electric motor's torque is a function of the speed at which it rotates. Many brushed AC motors have a linear toque curve as shown below. If the power output of the motor is equal to the torque (T) multiplied by the rotational speed in rad/s (w), what is the maximum power you can get out of the motor if the stall torque (Tstall) is 0.001 Nm and the no load speed (wno load) of 14,332 RPM? Give your answer in Watts. There are two ways to solve this: Use a stall torque and no load speed and plot the torque profile below and then plot the power versus rotational speed to find the maximum. The second method is to determine the mathematical relationship for power given the information at the start of the question and set the differential of power with respect to RPM equal to zero, and solve for the RPM to get the maximum. Tstall Wno load W