Given the following data, compute for the total excavation required for column footing/s. Write numerical values only. Use 2 decimal places. NAME COUNT L (m) W (m) D (m) T (m) F1 1.20 1.20 1.25 0.35 F2 8. 1.40 1.40 1.25 0.35 F3 8. 1.60 1.60 1.25 0.35 F4 8. 1.30 1.30 1.25 0.35

Given the following data, compute for the total excavation required for column footing/s. Write numerical values only. Use 2 decimal places. NAME COUNT L (m) W (m) D (m) T (m) F1 1.20 1.20 1.25 0.35 F2 8. 1.40 1.40 1.25 0.35 F3 8. 1.60 1.60 1.25 0.35 F4 8. 1.30 1.30 1.25 0.35

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A braced excavation 30 feet deep is proposed at a site underlain by clay, as shown in the sketch…

A: Given: A braced excavation 30 ft deep is proposed in a clay stratum having two layers with different…

Q: athJax webview Q.1 A strip-footing is 60 ft long and 10 ft wide. The strip-footing has a rectangular…

A: Given:- L=60 ft W=10 ft 3 Columns bearing capacity of the soil =10000 kg/m2 To find:- shear force…

Q: 3. An 8"diameter timber pole is fixed into a large concrete footing at grade and is completely pin…

Q: Calculate the Load distribution of slabs to beams 2, 3 and A using 10kPa load multiplied by the…

Q: 9- Consider the following operations in Bridge shallow foundation construction: 1. Placing steel 2.…

A: Shallow foundations disperse impact load throughout vast regions of near-surface topsoil to reduce…

Q: Q2. Compute the allowable bearing pressure using the Terzaghi's equation for the footing and soil…

A: for the water table consideration their is 2 case When the water table lies above the base of the…

Q: 4 Two footings on the same level, have qo=100 kPa each, one circular with a diameter of 3.0 m and…

A: The given data is: q0 = 100 kPa Diameter of circular footing (d) = 3 m Width of square footing (b) =…

Q: A (4x4) m footing is located at a depth of 4.5 m below the ground surface and subjected to eccentric…

A: unit weight of soil= 18.5 kn/m2 frictional angle = 32…

Q: Consider excavation of a simple long trapezoidal pit with a joint highlighted in the pit slope,…

Q: 1400 3800 4000 3600 BED ROOM KITCHEN 1400 2300 3800 BATHROOM 1500 DINING 3500 LIVING ROOM BED ROOM…

Q: Design a square concrete column footing to support a 300-mm × 300-mm reinforced concrete column that…

Q: Submit the following online or on paper: The footing below is a 5ft square. The soil immediately…

A: The unit weight of the soil above the footing, The unit weight of the soil below the footing, The…

Q: a. A layer of sand, of saturated unit weight overlies a layer of clay, of saturated unit weight. A…

A: It is required to draw the soil profile and find consolidation settlement of clay at it's centre.

Q: Carry out calculations for quantity of earthwork for a portion of a road from the data given in…

Q: Q#3:…

A: The allowable safe bearing capacity is given by: Where,

Q: Design a square concrete column footing to support a 300-mm × 300-mm

A: Givendata: Dimension of column = 300 mm x 300 mm Dead load = 130 kN Live load = 200 kN Compressive…

Q: The average correcte N60 = 7 in the effective zone for a square footing (1m x 1m) located at a depth…

A: If the soil support of the continuous foundation yields due to the load imposed by the foundation,…

Q: الموافق . Subject Date : 1 1 SA Strip footing I'm wide at its base موضوع الدرس التاريخ / is located…

A: Factor of safety (F) = 3 Determine the safe bearing capacity.

Q: So we briefly went over this in class. He only did a verbal explanation. I have also attached the…

A: Here load on the footing is not given Assume load on footing Q=1000 KN and Assume width B=2.0…

Q: SÍTUATION 6: A 2m square footing is placed 1.2 m below ground. Evaluate the following using…

Q: Problem 2. Twenty pieces of the footing shown below are to be used for a building project. Estimate…

A: Let us assume the clear cover for the given footing to be = 50 mm = 0.05 m In x-direction: (3-16mm…

Q: A rectangular column footing is to be designed to carry the following column loads: PDL = 850 kN MDL…

A: Column size 500* 500mPDL = 850 kNPLL = 690 kNMDL = 160 kN-mMLL = 190 kN-mL= 1.4Bf'c = 27.6 MPafy =…

Q: Total excavated soil The amount of backfill needed utilizing the excavated soil considering…

Q: Shown here is the cross-sectional detail of footing and dimensions are in millimeters. These are 12…

A: The dimensions of one footing are:- Length=2.7m Breadth=2.7m Height=1500mm=1.5m Volume of excavation…

Q: Assume that y A square foundation (B x B) has to be constructed as shown in Figure 17 kN/m², Y-20…

Q: Estimate for the number of 12mm diameter steel bars including the tire wire in kilograms if there…

A: Solution: Determine the length of one reinforcing cut bar Net length = 1 + 0.20 hook =…

Q: Calculate the ultimate bearing capacity per unit area of: (i) A strip footing 1 m wide (ii) A square…

A: Given data- strip footing 1 m widthunit weight of the soil γ=1.8 t/m3=18 kN/m3cohesion c=2 t/m2=20…

Q: 2. Determine soil bearing capacity by SPT numbers. Given: Soil SPT number: 10 Footing type: 3 feet…

Q: Consider the strip footing shown in the figure below. The soil consists of sand with f’ =36° and…

A: The angle of friction = 36° The effective cohesion (c') = 0 The saturated unit weight of the clay =…

Q: c. 75 mm

A: Minimum cover should be 75 mm.

Q: I. A shallow continuous foundation is to be constructed on a soil under the ground'. surface as…

Q: can someone resolve this? when I tried checking the process,, it gives different answers

A: Required Resolving the given steps

Q: If the square footing has an 800mm edge with a 300mm thickness, and that the 200mm x 200mm column…

A: Compaction: The reduction of air voids from the tightly packed soil particles is known as…

Q: By using the center line length method- find the foundation excavation quantity plotted in chart…

A: There are various methods of estimating the quantities in a construction activity. Two of the most…

Q: Prepare a spreadsheet to compute settlement of square footings using the e@log@p method.…

A: Given:- Cr/(1 + e0), Cr/(1 + e0) To find:- settlement

Q: Given data for column D = 350 Kips, L=250 Kips, 20 in x 20 in, 8#8 bars, fy = 50 ksi, f= 4 ksi, and…

A: Given data, D = 350 kips L = 250 kips qa = 3.5 ksf L = 1.5B

Q: Simon did plate load test and its shown in graph. Assume that plate dimensions are 1.5m x 1.5m.…

A: It can be observed from the graph that at a settlement of 60 mm, there is a sudden drop in the load.…

Q: to be constructed on able is at depth 15 pacity and the colum

Q: Variable X in this question is that last digit of your student ID. Enter X here: X = A shallow…

A: Given: water table is 5m below foundation.net ultimate bearing capacity =450kPa Here foundation is…

Q: For the wall footing given in the figure, determine the reinforcement in both You do not have to…

A: Given Data:WD=30k/ftWL=40k/fttw=18inB=10ftfc=4ksi,fy=60ksi

Q: H = 20 kips 4 ft X P = 50 kips W 8 ft y y M = 60 ft-kips W = Weight of Footing and Surcharge = 20…

Q: Two columns 300mmx300mm and 400mmx400mm are loaded by axial and bending forces as shown. They are to…

A: Footing : A footing is constructed with concrete below the ground. A footing is a part of foundation…

Q: 7.64 V) D*tan R 3- D = H = 2 for conical spoil pile and %3D tan R 1/3

Concept explainers

Measuring site work, Excavation and Piling

Bid drawings typically include very little material about the precise requirements of site work operations, measuring site work and excavation work differs from measuring most other works on a construction project. The actual site work conditions are not provided and also the dimensions of the excavations are not known during the pre-construction phase. The precise measurement of the excavation and backfill of the earth material and topsoil is important for a contractor to decide upon the total cost required for the process. All the works should be carried out under OSHA (Occupational Safety and Health Administration) standards to ensure the safety of the workers.

Question

Given the following data, compute for the total excavation required for column footing/s. Write numerical values
only. Use 2 decimal places.
NAME
COUNT
L (m)
W (m)
D (m)
T (m)
F1
8
1.20
1.20
1.25
0.35
F2
8
1.40
1.40
1.25
0.35
F3
8
1.60
1.60
1.25
0.35
F4
1.30
1.30
1.25
0.35

Type of Paint used in Woods. (use lowercase only)

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Measuring sitework, excavation and piling

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Calculate the Load distribution of slabs to beams 2, 3 and A using 10kPa load multiplied by the tributary width. Yellow represents columns. Red represents beams.
Q4: For flexible footing shown below, find the immediate surface settlement below the point a. dq 200 kPa, -0.5, E 22800 kPa S - " (1-, Use l, 0.76
X=30
Problem 2. Twenty pieces of the footing shown below are to be used for a building project. Estimate the steel reinforcing bars required if the length of the bars to be ordered is 6.060 meters. 0.60M COLUMN 1.20M PLAN OF FOOTING 3-Ø16MM BARS 6-Ø12MM BARS FOOTING COLUMN BARS COLUMN COLUMN TIES 3-Ø16MM BARS 6-Ø12MM BARS (TYPICAL) 0.30M www. w SECTION OF FOOTING
Calculate the Load distribution of slabs to beams 3, 4 and C using 10kPa load multiplied by the tributary width. Colored box represents columns and uncolored represents beams.
PLEASE READ THE QUESTION AND DON'T COPY PASTE ANYONE'S ANSWER. ANSWER WHAT IS ASKED IN THE QUESTION DON'T POST RANDOM ANSWER
A rectangular footing 1.5 m x 1 m is shown in Figure below, Determine the magnitude of the gross ultimate load applied eccentrically for bearing capacity failure in soil. Use Effective Area Method. 0.1 m y = 18 kN/m = 30 F Im 1.5 m 0.1 m}+>{ m Select one: O a. 752 KN O b. 276 KN O c. 572 KN O d. 627 KN
B Calculate the ratio of the Ultimate Shear Force to Shear Capacity in one-way shear. Consider critical case only. A rectangular footing has dimensions shown and is acted upon by a dead load of 653 kN and a live load of 647 kN. The column dimension is 269x677 mm where the shorter dimension is parallel to B. The thickness of the footing is 442mm. f'c-28 MPa and fy=420 MPa for diameter 20mm bars. A=2.9m and B=4.8m
Find the number of 4" CHB to construct the fence. Use the table 1 for Cement, Sand, and gravel computations.
Suppose a building is supported on shallow foundation. The building has 4 Footing Group 1 footings, 4 Footing Group 2 footings and 1 Footing Group 3 footing. Dimension for Footing Group 1 is (length, width, depth) = (2.5 meter, 2.5 meter, 800 mm) Dimension for Footing Group 2 is (length, width, depth) = (2.8 meter, 2.8 meter, 1000 mm) Dimension for Footing Group 3 is (length, width, depth) = (3.2 meter, 3.2 meter, 1200 mm) Reinforcement orientation Footing Group 1: 16 mm diameter reinforcement @ 200 mm c/c in both directions, and top and bottom of the footing. Reinforcement orientation Footing Group 2: 16 mm diameter reinforcement @ 150 mm c/c in both directions, and top and bottom of the footing. Reinforcement orientation Footing Group 3: 16 mm diameter reinforcement @ 100 mm c/c in both directions, and top and bottom of the footing. Clear cover for column is 75 mm. Unit price of Concrete: 350 AUD/m3 Unit price of Steel: 2.0 AUD/kg Density of Steel: 8,000 kg/m3 Calculate…
A structural engineer finished a design of a library. They determine that each column will carry 1000 lbs. the soil beneath the footing has the properties: gamma= 130 pcf, c= 75psf, phi= 40 degrees. The groundwater table is of great depth so it’s no concern. Sketch figures. What is the minimum size of the footing for a factor of safety of 3? Case 1: assume square footing Case 2: assume round footing
UPVOTE will be given! STRENGTH OF MATERIALS A rectangular footing has a dimensions shown and is acted upon by a dead load of 1,929 kN and a live load of 1,515 kN. The column dimension is 317 x 667 mm where he shorter dimension is parallel to B The thickness of the footing is 566mm. f'c=28 MPa and fy=420 MPa for diameter 20mm bars. A=2.7m and B=4m Calculate the number of bars along the long direction?