Given P=30kN. Using the Method of Joint, determine the force in Member FG (in kN). (positive indicates tension, negative indicates compression)

Q: 1.2 m 0.2m 0.6

A: Given data:Mass of plywood (m) = 31 kg.Floor covered by plywood = The plywood sheet hinged at A and…

Q: The stepped bar has a thickness of 15 mm. Determine the maximum moment that can be applied to its…

A: Given data:The thickness of the stepped bar is t = 15 mm.The allowable bending stress is σallowable…

Q: 7.127 Determine the coordinates of the centroid of the volume. 40 mm 120 mm 100 mm Problem 7.127 B…

A: Consider three cylinders-First cylinder solid-Second cylinder hollow-(this cylinder is inside solid…

Q: Determine the vertical displacement of point B. Each A-36 steel member has a cross- sectional area…

A: Given,A = 400 mm2E = 200 GPa

Q: A 2x2 m tank with vertical sides contains oil with a density of 900 kg/m3 to a depth of 0.8m…

A: Area of tank  A = 2 x 2 = 4 m2Density of oil  = 900 kg/m3Oil depth in tank ho = 0.8 mwater depth in…

Q: For the frame shown, determine all support and connection forces on cach member. The 400-lb-ft…

A: Given:The moment applied is To find:All the support reactions and the connection forces.

Q: Diesel tends to wait until the rabbit is closest before starting to chase. If the rabbit is…

A: To find:the equations for the rabbit’s velocity.Given:The

Q: A coin of mass m is left at the edge of a rotating disk, a distance r from the center. The disk is…

A: mass of coin = m radial location of coin r = 2 mfriction coefficient between coin and disk

Q: Problem 4: An airplane lands on the straight runway, originally traveling at 135 ft/s when s-0. If…

A:

Q: Explain with a diagram how the bimetallic temperature switch is use to measure

A: Bimetallic temperature switch to be explained with diagram for the measurement.

Q: We are offered some pipes made of a new kind of plastic. To test their roughness, we pump water…

A:

Q: DON'T USE AI | DON'T USE AI | DON'T USE AI | DON'T USE AI | A simple beam AB is loaded as shown in…

A: The maximum allowable stress is .

Q: 5) Outdoor air enters an air-conditioning system at 10°C and 70% RH at a steady rate of 35 m³/min,…

A:

Q: In the system shown it is known that the blocks slide with a constant speed; determine the value of…

A: Given:To find:kinetic friction between the block C and the plane.

Q: Determine the resultant force stress produces on top flange A and bottom flange B then compute…

A: The moment applied is

Q: 4. An ideal Otto cycle has a compression ratio of 8. At the beginning of the compression process,…

A:

Q: Required Information The part shown is made from AISI 1030 CD steel and is loaded at point C with…

A: Given : material - AISI 1030 CD diameter of bar d = 12 mmNote : Yeild strength for AISI 1030 CD is…

Q: can you sesolve? solution seems incorrect

A: Given data: OA=300 mm= 0.3 mAB=1200 mm= 1.2 mBC=CD=450 mm= 0.45 mWe know that linear velocity of the…

Q: A rain gutter is to be made of aluminum sheets that are 16 inches wide by turning up the edges 90°.…

A: From the given diagram of the main gutter,base = 16-2xheight = xThe Area is given as,Area =…

Q: Find the acceleration of the specified object. (Hint: Recall that if a variable is changing at a…

A:

Q: Question- 4 The following illustration shows the construction parts of the drum brake. From the…

A:

Q: seems option 3rd is correct , Please show work within 30min.

A:

Q: 5)A bar is fixed at both ends, has shear modulus G = 28 GPa with a solid cross section. Part A has a…

A: A bar is fixed at both ends,has shear modulus G = 28 GPa = 28 × 103 MPa with a solid cross…

Q: Five a) Determine the equations of motion and the natural frequencies of the system shown in the…

A:

Q: P W PROB 1. DETERMINE THE と MAXIMUM FORCE THAT CAN BE APPLIED FOR THE BOLTED CONNECTION IF STROBS IS…

A: Disclaimer:As per our guidelines, we will answer the first 3 questions. Resubmit with the particular…

Q: A Ferris Wheel, with radius 50 ft., turns counterclockwise one revolution every 18 seconds. Bryce…

A: Given:To find:Determine whether the Susan have a chance to catch the ball?

Q: Determine the vertical displacement of point B. Each A-36 steel member has a cross- sectional area…

A: Given,A = 400 mm2E = 200 GPa

Q: 4-42. Draw the shear and moment diagrams for each member of the frame. Assume A is fixed, the joint…

A: The free-body diagram of the given beam is shown below.

Q: Problem 6-Analysis of a nozzle flow ( The stators in a gas turbine are designed to increase the…

A: List the assumptions and approximations that were needed to solve this problem.Steady-state…

Q: Consider a mass-spring system hanging vertically. The mass is 0.15 kg and the spring constant is 0.3…

A:

Q: How would this fourbar linkage actually look?

A: To determine the four bar linkage from the above drawing

Q: Click on Explore ID. Check the boxes labeled sum and values located in the top right corner. Click…

A: Given:To find:The magnitude and x and y components of vector s.

Q: 9-51 Problem 9-51 Dimensions in millimeters Estimate the safe static load F for the weldment shown…

A: Given:Design factor 2Allowable shear stress 190 MPaTo determine:The force applied

Q: 6-119. If the beam is made from a material having an allowable tensile and compressive stress of (σ…

A:

Q: Question-3 The following illustration shows the construction parts of the disc brake. From the…

A:

Q: Two 13-kg uniform bars are connected to form the linkage shown. Neglecting the effect of friction,…

A: L = 0.6 mm = 13 kgFInd the reaction at D

Q: Determine the net work done on the system, in kJ/kg. Write your answer to one decimal place using…

A: To determine the net work done in the systemnet heat rejected in the systemfor the refrigerant is…

Q: Often, the properties of multiphase alloys may be approximated by the relationship E (alloy) = EaVa…

A:

Q: For all the following problems, 5. a) b) You need to show at least 3 iterations calculated manually…

A:

Q: pipeline. How much steam is in the tank at the end of the filling process, and what is its…

A: Take the tank as CV.First Law Equation for the process is:Note: Potential energy and kinetic energy…

Q: Calculate the angle of twist at point A. A for the following diagrammed problem. There is a 1600…

A: The diameter of shaft AB is .The diameter of shaft CD is .The diameter of gear B is .The diameter of…

Q: 6. A transmission shaft carries a pulley midway between the two bearings. The bending moment at the…

A:

Q: A) A circular rod with a gage length of 3.6 mm and a diameter of 2.3 cm is subjected to an axial…

A: Given:Rod diameter (d) = 2.3 cm = 0.023 mGage length (L) = 3.6 mm = 0.0036 mAxial load (P) = 51 kN =…

Q: Locate the centroid and calculate the moment of inertia about the x and y-axis 20mm 25mm 30mm Q 30mm…

A:

Q: Calculate the temperature in K of air at 13.2 MPa with a specific volume of 2.52×10-3 m3/kg using…

A: Here we will use the compressibility chart to get the temperature

Q: Task (II) Wind Turbine: Consider the following table: Fan Speed Low Medium High Wind speed 8.20 9.70…

A: (A

Q: Consider the beam and loading shown in the figure below. The beam has a flexural rigidity of El over…

A: Flexural rigidity for AC= EIFlexural rigidity for BC=c2EIThe objective is to determine:a) reactions…

Q: ᴛᴡᴏ ᴍᴀᴛᴇʀɪᴀʟꜱ ᴡᴇʀᴇ ᴛᴇꜱᴛᴇᴅ ɪɴ ᴛʜᴇ ʟᴀʙᴏʀᴀᴛᴏʀʏ ᴡɪᴛʜ ᴛʜᴇ ꜰᴏʟʟᴏᴡɪɴɢ ᴅᴀᴛᴀ ᴜꜱɪɴɢ ᴛʜᴇ ᴜɴɪᴠᴇʀꜱᴀʟ ᴛᴇꜱᴛɪɴɢ…

A: Given:For material A:For material B:To find:ᴀ) ʏɪᴇʟᴅ ꜱᴛʀᴇꜱꜱ, ʙ) ᴘʀᴏᴘᴏʀᴛɪᴏɴᴀʟ ʟɪᴍɪᴛ, ᴄ) ᴇʟᴀꜱᴛɪᴄ…

Q: Given an otto cycle . p1= 1[bar] , T1=28[c] , effiency = 43% , w(net)= 480[kj/kg]. A. find the…

A: Given-Initial pressure,To Find-A. Find the tempture , specific volume and pressure in states…

Q: A homogeneous, 4-ft-wide, 12-ft-long rectangular gate weighing 800 lb is held in place by a…

A: Given-Data:To-Determine:Tension in the cable.

Free Body Diagram

The system of forces acting on a body tends to either rotate it or make the body undergo motion. In general, when an external agent exerts a force on a body, the body undergoes translational motion and rotational motion. The body has six degrees of freedom under the influence of that force. Here, three degrees of freedom are from the translational motion while the other three are from the rotation motion. However, sometimes the bodies are not allowed to undergo any motion and are fixed, under such conditions the body is said to be constrained.