Given: oxygen leaks slowly through a small orifice in an oxygen bottle. the volume of the bottle is 0.1 m³ and the diameter of the orifice is 0.12 mm. the temperature in the tank remains constant at 18% and the mass flow rate is given by m = 0.68 PA/JRT Find: How long will it take the absolute pressure to decrease from 10 to 5 MPa?

Given: oxygen leaks slowly through a small orifice in an oxygen bottle. the volume of the bottle is 0.1 m³ and the diameter of the orifice is 0.12 mm. the temperature in the tank remains constant at 18% and the mass flow rate is given by m = 0.68 PA/JRT Find: How long will it take the absolute pressure to decrease from 10 to 5 MPa?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Orifice Given:As = 3m2C = 0.92Ao = 0.01m2 Determine the time for the depth of liquid in the tank to be 0.8m
A cylinder glass tubing 2.8 cm. inside diameter and 90 cm long with one end closed is immersed vertically with the open end down into a tank of cleaning solvent (sp.gr. = 0.73) until only 5 cm. of its length remain above the liquid surface. If the barometric pressure is 1 kg/cm2 and neglecting vapor pressure, how high will the fluid rise in the tube? -2.8cm- Scm 90cm Clearing solvent X (S=0.73) Do not write the unit. You will only input the numerical answer in the space provided. Unit of the Correct Answer: cm Decimal Places required in the final answer: 2
A 3 cm orifice plate is placed within a 4 cm pipe in which methanol at 20 °C (SG =0.7884 and dynamic viscosity (μ) = 0.5857 cP) is flowing through. If the flow ratepassing through the pipe is 3.1 litres per seconds, determine the pressure difference thatmust be measured around the orifice plate. The discharge coefficient of the orifice can be calculated by Where, β is the ratio of orifice diameter to pipe diameter and Re is the Reynoldsnumber.
Problem 2 -50 A glass 12 cm tall filled with water is inverted. The bottom is open. What is pressure at the closed end? Barometric pressure is 101.325 kPa. the Ans: 100.15 kPaa Problem 2 -51 In Figure 13, in which fluid will a pressure of 700 kPa first be achieved? Ans: glycerin Po = 90 kPa ethyl alcohol p= 773.3 kg/m 60 m oil p= 899.6 kg/m? 10 m water p = 979 kg/m glycerin p = 1236 kg/m 5 m 5 m
A 10 cm diameter solid cylinder of height 10 cm weighing 0.40 kg is immersed in a liquid (800 kg/cm^3) contained in a tall metal cylinder having a diameter of 13 cm. Before immersion, the liquid was 8 cm deep. At what level from the bottom will the solid cylinder float? W, = 0.40kg %3D 10cme tank New L.S. Original L.S F,
Measurement of viscosityA cylindrical tank with a diameter D' = 50 mm is emptied by a tube with diameter D = 1mm and length L = 1m. The flow in the tube is laminar. Determine the kinematics viscosity , knowing that the level in the tank H drops from H1 = 0.5m at t1 =0 to H2 =0.25 m at t2=50 min.
(a) Glycerine at 25 °C flows through a straight copper tube (D = 73.8 mm), at a flow rate of 180 L/min. Calculate the pressure difference between 2 points which are 25.8 m apart, if the first point is 0.68 m below the second point. Gven: At 25 °C density and dynamic viscosity for glycerine is 1286kg/ and 0.96 Pa.s respectively(b) If benzene at 50 °C is used in question (a) above instead of glycerine, evaluate the new pressure difference. ...
•Determine the unit weight of the liquid when it is at the level shown. (Express the answer in English unit) •Determine the weight of the liquid. (Express the answer in English unit) •Assuming no mixing of liquids occur, if glycerin (SG= 1.26) is poured into the tank: a.) it will sink to the bottom of the tank b.) it will float on the surface of the liquid c.) it will be suspended in the liquid * answer should be in 3 decimal places
- In a mano meter shown, the fluid from A to B is mer cury (s-q= 13-0) and from e to C,the flud is oil Csg. 0-80). At what height "h" Of mercury Of 226.3 gram cm at C. ue density of watr p= 1granl Com?. oil 1-20m will give a pressure mercury
5. Airat standard conditions enters the compressor shown below through a 2.4-in diameter pipe at 10 cfs. It leaves the tank through a 1.2-in diameter pipe at a velocity of 700 fps and has an increased density. Determine the average time rate of change of air density within the tank. 2.4 in 10 cfs 1.2 in 700 fps 0.00350 slugs/ft Tank Volume = 50 ft 0.00238 slugs/ft
The cyclindrical tank with hemispherical ends shown in Fig. contains a volatile liquid and its vapor. The liquid density is 800 kg/m', and its vapor density is negligible. The pressure in the vapor is 120 kPa (abs), and the atmospheric pressure is 101 kPa (abs). Determine: (a) the gage pressure reading on the pressure gage; and (b) the height, h, of the mercury manometer. Open Vapor 1m 1 m Liquid 1 m Mercury E E
The tank contains a liquid having a density of 2.52 slugs/ft^3 10 in 5 ft 10 ft. 7 ft Pliquid 2. 52 slugs/ſt³ %3D a. Determine the unit weight of the liquid when it reaches the indicated level. b. Determine the liquid's weight. Use English units to express your response. c. Assuming no mixing of liquids occur, if glycerin (SG = 1.26) is poured into the tank, will it sink to the bottom, or will it float on the surface of the liquid, or will it be suspended in the liquid?