Given is the buck-boost(Cuk) converter with the following data: Input voltage Vg = 42 V Output voltage V = 24 V Switching frequency fş = 200 kHz Load resistance R = 10 Q a. Determine, D,V₁, V₂, I₁, and 1₂ b. sketch the inductor voltage and capacitor current waveforms indicating time and magnitude values. c. Determine the value of L₁,L₂, and C, so that Al₁ =1.2% of 1₁, Al2 = 3% of 12 and Av₁ = 2% of Vg. d. Sketch i(t), 1₂. (t) and v₁ (t)

Given is the buck-boost(Cuk) converter with the following data: Input voltage Vg = 42 V Output voltage V = 24 V Switching frequency fş = 200 kHz Load resistance R = 10 Q a. Determine, D,V₁, V₂, I₁, and 1₂ b. sketch the inductor voltage and capacitor current waveforms indicating time and magnitude values. c. Determine the value of L₁,L₂, and C, so that Al₁ =1.2% of 1₁, Al2 = 3% of 12 and Av₁ = 2% of Vg. d. Sketch i(t), 1₂. (t) and v₁ (t)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Please answer all subparts for like either dislike is ready..
Vprip ~ Vgiris Voltage-Time relationship in the signal first half cycle of the doubler circuit and the wM A w A wA direction of current flow on the circuit. For the input voltage, give a sine signal with a frequency of 10Vp-p 1kHz . Use a value of 1µF for the capacitor. For diodes, use an ideal diode by making VD = OV. Obtain and report the output voltage in graphical and tabular form. Find the output voltage.
Q4: Design a buck-boost converter to provide an output voltage 12V from a source that varies 'between 10V-16V. Given the load resistor is 10 ohm. assuming the frequency is 50 KHz and the output voltage ripple is 1.5% Specity: a. The duty ratio. b. The value of inductor. c. The value of capacitor. Note: Determine the values of inductor and capacitor with D1 only.
-Design a buck converter that has an output of 12 V from an input of 18 V. The output power is 10 W. The output voltage ripple must be no more than 100 mV p-p. Specify the duty ratio, switching frequency, and inductor and capacitor values. Design for continuous inductor current.
A step down converter is operated with a duty cycle of k = 0.75. The input voltage is Vs = 20V, and the load is: L = 5mH, R = 1502. The minimum inductor current is I₁ = 0.1A. The maximum inductor current is: Select one: a. 1.9 A b. None of these OC. 0.9 A O d. 1.1 A Oe. 2 A
i need the answer quickly
double clipper circuit Zener diodes 1N4733A has a voltage of 5.1 V and 1N4735A has a voltage of 6.2 V with a resistor R=300ohms has been used. you may like to increase the input to a 12 VRMS AC source in order to see the clipping at 7volt. Please, Do the theoretical calculations and plot the expected waveforms by hand. ( I have its multisim design and only needs theoretical calculation and hand drawn graph of it to compare to its data that I have collected from multism.) Thanks
Kindly solve all the parts for me
For the buck-boost converter, determine the duty cycle, the switching frequency, and the inductor current ripple. The output voltage ripple is about 1%. vs 10 V, mH, C 0.5 micro.F, Vout=-20 V, R-IO Q
In the given circuit, D1 is Silicon diode and D2 is a zener diode with breakdown voltage of 6.8V. Assuming RC time constant of circuit >> T. Find the Maximum and Minimum value of the output waveform.
A certain regulator has a no-load output voltage of 16 V and a full-load output voltage of 15.6 V. If the full-load current is 210 mA, express the load regulation in %/mA. Your Answer:
1.Find condition to know Diode on or off, Von = 0.7V. 2 Find relative equation between Vo and Vin