Given below is the result of a sieve analysis done on a soil sample. Sieve No.   Diameter   Percent Passing % 4   4.750   95 10   2.000   83 20   0.850   69 40   0.425   50 60   0.250   27 100   0.150   13 200   0.075   7 Pan   ---   0 Determine the value of the coefficient of uniformity.

Q: L 40 PL 30 Determine its classification using USCS.

A: soil is classified as MI

Q: Situation 3. Following are the results of a sieve analysis. Determine: a. Cu b. Cc c. So Sieve No. 4…

A: To Determine :- a. coefficient of uniformity, Cu b. Coefficient of curvature, Cc c. Sorting…

Q: Percent finer by weight 5. [2 points] Multiple choice: In the figure below, soil G is a 100 90 80 70…

A: Here's a step-by-step explanation of how I determined that soil G is a coarse-grained…

Q: Given below is the result of a sieve analysis done on a soil sample Sieve No. Diameter Percent…

A:

Q: Using the data for a sieve analysis shown below, the percent retained on the 2 mm sieve is most…

A: Given, Sieve analysis data   To find : Percent mass retained on 2.36 mm sieve

Q: Show how did equation 1 and 2 resulted? I have tried it but i resulted to "8tan(40) - C…

A: Given data in question  Loads 8, 16 and 3kN Angle 20 and 40° To find out  Value of C Solve equation…

Q: Given below is the result of a sieve analysis done on a soil sample. Sieve No. Diameter Percent…

A:

Q: Write step by step the calculations, if it is necessary. a. Identify the type of sieving series. b.…

A: a.   There are two type of sieve process. They are dry and wet sieve analysis. In dry sieve analysis…

Q: SUBJECT: SOIL MECHANICS Classify the soil using USCS (with explanation) СHOICES: a. CL (lean clay…

A: By using the guidelines of USCS. PERCENTAGE Passing #200 and #4 are used to find the correct…

Q: Following are the results of a sieve analysis: U.S Sieve No. Diameter (mm) Mass Retained (grams)…

A:

Q: Given below is the result of a sieve analysis done on a soil sample. Sieve No.…

A: ASKED: To determine the coefficient of uniformity for the given soil.   Given, Sieve No. Opening…

Q: Given below is the result of a sieve analysis done on a soil sample. Sieve No.   Diameter   Percent…

A:

Q: effective particle size.

A: “Since you have posted a question with multiple sub-parts, we will solve first three subparts for…

Q: Given below is the result of a sieve analysis done on a soil sample. Sieve No.   Diameter   Percent…

A: since we know that coefficient of curvature = D230D10×D60   To calculate the D30,interpolate between…

Q: The given data shows a sieve analysis of soil samples A, B and C. Percent Sieve Diameter Finer No.…

A:

Q: The particle size characteristics of a soil are given in the table. Using MIT method, determine:…

A: Given data,

Q: • Problem 2- . The following are the results of a sieve analysis. Determine the percent finer than…

A:

Q: е. 650 ton of Sample1 and 150 ton of Sample 2 are available. How many Kg of particle size bigger…

A: e. Calculate the % of retained for each sample. Calculate the same proportion with 650 ton of Sample…

Q: In the picture is a distribution graph of the sphericity of a sample of aggregate materials. The…

A: In the picture is a distribution graph of the sphericity of a sample of aggregate materials. The…

Q: Given below is the result of a sieve analysis done on a soil sample. Sieve No. Diameter Percent…

A:

Q: Determine the value of the coefficient of uniformity. Round off to

A: Draw the gradation curve as shown below

Q: From the results of a sieve analysis given below compute for the effective size of D10, D30 and D60

A: Results of sieve analysis are given as Sieve number Mass retained (g) 4 0 10 40 20 60 40…

Q: Given below is the result of a sieve analysis done on a soil sample. Sieve No. Diameter Percent…

A:

Q: The following are the results of a sieve and hydrometer analysis. Analysis Sieve number/grain size…

A: The grain size distribution curve is obtained from the result of sieve size analysis and it is…

Q: Determine the value of the coefficient of gradation/curvature.

A: The results of sieve analysis are generally shown on semi-logarithmic plots known as Particle size…

Q: U.S Sieve No Opening (mm) Mass of soil retained (g) 4 4.75 28 10…

A: KINDLY NOTE, as per our company guidelines we are supposed to answer only first sub-parts. Kindly…

Q: Given below is the result of a sieve analysis done on a soil sample. Sieve No.   Diameter   Percent…

A: GIVEN Seive no. Sieve diameter, Percentage Passing through each seive size. To Determine Coefficient…

Q: iven below is the result of a sieve analysis done on a soil sample. Sieve No.   Diameter   Percent…

A: sieve size  in mm % finer than 4.75 96 2 90 0.85 66 0.425 39 0.25 26 0.15 14 0.075 5…

Q: A 1000g of sand has been soaked for at least 24hours prior to lab. After drying the sample to…

A: Solution: Given data: i) weight of the sand sample taken = 1000 g ii) W1 = sample 1 + can 1 = 800 g…

Q: Sieve No. Diameter Percent Passing % 4 4.750 97 10 2.000 80 20 0.850 72 40 0.425 43 60 0.250 27 100…

A: We have to find the coefficient of uniformity

Q: Question 29 Given below is the result of a sieve analysis done on a soil sample. Sieve No. Diameter…

A:

Q: a. Given the table above solve for the following. Show your complete solution and round off to three…

A:

Q: The particle size characteristics of a soil are given in the table. Using USDA method, determine:…

A:

Q: Given below is the result of a sieve analysis done on a soil sample. Sieve No.   Diameter   Percent…

A:

Q: The results of the sieve analysis done on a soil are shown below. Sieve No. Diameter Soil A 4 4.760…

A: Given Seive size and Percentage Passing through each seive. To Determine Classification of soil…

Q: Question 2 The results of the sieve analysis done on a soil are shown below. Sieve No. Diameter Soil…

A: Given Sieve No, seive diameter, Percentage Passing of soil A through each seive sizes. To Determine…

Q: From the tabulation of data and result of determining setting time of cement, determine the initial…

A: Penetration rate in mm corresponding to time is given and it has been asked to determine initial…

Q: Given below is the result of a sieve analysis done on a soil sample. Percent Passing % Sieve No. 4…

A:

Q: one is finer: Soil A or Soil C?

A:

Q: The following are the results of a sieve analysis. Determine the percent finer than sieve number 60…

A:

Soil classification and characteristics

Soil classification is a method of categorizing soil based on its properties, types, and uses. The motive of soil classification is to arrange various types of soils and divide them into groups for various engineering and agricultural purposes. Soil classification is carried out by various agencies as per their purposes. From an engineering perspective, soil classification is done to find out the suitability of soil for various construction purposes like the construction of dams, foundations, highways, infrastructures, and so on. For engineering purposes, the soil is classified by the following systems: