Given a series circuit with R= 20, L = 2 mH, and C = 5 uf, a) the resonant frequency is Hz (round off numerical answer without decimal point) b) the quality factor is (round off numerical answer without decimal point) c) the bandwidth is rad/sec (round off numerical answer without decimal point) d) if the R is changed to 0.2 0, Q ill be and BW will be rad/sec (round off numerical answer without decimal point)

Given a series circuit with R= 20, L = 2 mH, and C = 5 uf, a) the resonant frequency is Hz (round off numerical answer without decimal point) b) the quality factor is (round off numerical answer without decimal point) c) the bandwidth is rad/sec (round off numerical answer without decimal point) d) if the R is changed to 0.2 0, Q ill be and BW will be rad/sec (round off numerical answer without decimal point)

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter24: Resistive-inductive-capacitive Parallel Circuits

Section: Chapter Questions

Problem 4RQ: A tank circuit contains a capacitor and an inductor that produce 30 of reactance at the resonant...

See similar textbooks

Similar questions

Calculate the resonant frequency of the median resonator. The value of D2= 6.05 cm, D1= 1.72 cm,Lreal= 1.89 cm and the temperature is 25°. Also obtain the value in units of the frequency ofresonance.
HW: Determine Zin, Zo and the small-signal voltage gain. P type C₁ C₂ Vo D Vin Rs RD RL SINT 4k 2k 4k Zin -5V Zo +5V = kp 1mA/V2 Vr = -0.8V λ=0 Bobin painleido XL=SL = jwL Frequency Response Sm= 2 kp (VSG₂Q +VT) rd = 1 A IDQ ID= kp (VSC₂+V+) ² notion Xc = Copacite 1 (WC 345
Answer the following questions: 6. Describe the current and impedance in a series RLC circuit at resonance.7. Describe the current and impedance in a parallel RLC circuit at resonance.
1. Determine the break frequency @, of the numerator term and the break frequency @,2 of the denominator term in the following transfer function: (jø0.01+1) (jo0.1+1) H(jø) =100-
Determine the break frequency in KHZ of the RC low-pass circuit below. Assume that Resistor value is 3 KQ and Capacitr value is 0.02uF.
The resonant converter having fixed value of resonant frequency 48 Hz and capacitance of 2 muF. Find the inductance of this resonant converter a. 2.64 H b. 5.49 H c. 33.12 H d. 34.51 H
2) What is the closed loop gain and bandwidth in the circuit below? What is the output voltage at 1 kHz and at 10 MHz? 1 Vin 25 mVp P-p R₁ 180 Ω + Rf 1,8 ΚΩ LF157A Vout
The below 4 figures are the angle of the transfer function of passive filters. Phase (deg) -45- Phase (deg) (Cep) sid 45 10 10 Frequency (radisec) 10² Frequency (rad/sec) Figure-1 shows the frequency response of Figure-2 shows the frequency response of Figure-3 shows the frequency response of Figure-4 shows the frequency response of 4) ( + 4 10 10" 10
Ele fle For the figure below determine the lower culiff frequencies and sketch the frequency response using Bode plot. C₂ = 10MF CE=20μF Ce=1MF R₁ ₂ R₁ = 40KR₂ R₂=10kr, RE=2KR₂ R₂=4K₁²₂ R₂₁ = 22KR²₂ B = 100, Vcc=20V V₁ R₂5 Vec Wie Bre Re 9 RL
. A resonant circuit has a peak output voltage of 4.5 mV. What is the voltage output at the upper and lower cutoff frequencies?
Eill in the blank with corect answers B Frequency Series Resonance - Impedance vs. Frequency. The graph of impedance against frequency for an RLC series resonance circuit is shown in the picture. At which point the current will be maximum At point A At point C At point B At point D The inner most layer of an optical fhotI Is cantu Impedance
Which of the following statement is true for the figure shown below. O LTI system RC low-pass filter - labAlive O RC low-pass fiter- Properties File Run Simulation Help Cutoff frequency > 320 MHz V O Signal Generator - Properties Amplitude Frequency < Output 1.73 H ic) 45.0 MHz On Waveform Sine The voltage at the output is higher compared to the initial voltage at the input O b. The output voltage cannot be determine since the input frequency is too high compare to cutoff frequency O. The voltage at the output is lower compared to the initial voltage at the input O d. The voltage at the output is equal to the initial voltage at the input