Given: A bracket as shown subjected to a nominal dead load of 8 k and a nominal live load of 52 k. Assume the thickness of the angles is ½“, and the supporting member has a thickness greater than that of the angles. Fy = 50 ksi. Note: the bracket plate is welded to the angles. Find: a) The number of 7/8" A325X bolts required if prying is neglected b) What angle thickness is required to essentially eliminate prying effects?

Given: A bracket as shown subjected to a nominal dead load of 8 k and a nominal live load of 52 k. Assume the thickness of the angles is ½“, and the supporting member has a thickness greater than that of the angles. Fy = 50 ksi. Note: the bracket plate is welded to the angles. Find: a) The number of 7/8" A325X bolts required if prying is neglected b) What angle thickness is required to essentially eliminate prying effects?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

(2) The connection shown below is bolted with 3/4 inch diameter, Group A slip-critical bolts in single shear. Assume that the bearing strength is adequate and use an elastic analysis to determine the maximum factored load that can be applied. 5.5" Column Flange o o O o o Gusset Plate 4sp. @3" O O 4" 30⁰ P₁ = ?
*A bracket is held in place using a circular pattern of 6 bolts as shown. The circular pattern radius is 2 inches. The force is F=600 lbs. The bolts are 4 in UNC 20 of SAE Grade-5. Assuming the clamping force is lost (no friction) what is the factor of safety guarding against bolt deforming (yielding) using DET. The shear forces are taken by the bolt shank areas. 20 a) 0.95 b) 1.35 c) 2.38 d) 3.55 e) 4.62
2-PL10x1/2 A-36 Bolts are 7/8 in A-325, threads are not excluded. All edge spacings are minimum | 3" | 3" | о PL 10x3/4 A-572Gr50 a) Determine the nominal bolt capacity. b) Determine the nominal bearing capacity for each plate. c) Determine the nominal rupture capacity of each plate. d) What is the nominal capacity of the connection? e) Using LRFD, is this connection capable of supporting a dead load of 150 kip and a live load of 100 kip?
5) Calculate P the allowable tensile load for the butt joint shown. Each A325-N high-strength bolt has a diameter of 0.9 inches. The plates are made of ASTM A36 steel. If the applied load is 200 kips, is this connection adequate? If not, what needs to be changed so that this connection can handle an applied load of 200 kips? P- ФФ P ! 12"x " P. P.
2. Consider the connection on the following angle L7 x 4 x О О О 1.5 3" 3 + 3 3 + + + Use preferred material for L. All bolts are 1" A-490-X bolts. Edge distance is 1.5”. a) Determine the nominal bolt capacity. b) Determine the nominal bearing capacity for each plate. c) Determine the nominal rupture capacity of each plate. d) What is the nominal capacity of the connection?
Determine the load-carrying capacity of the 2 PL 5/16 x 3 tension member shown based on the limit states of weld/base metal (tension member only) capacity. The weld is 3/16 inch E70 and the plate is grade A36. PL ½x 6 2 PL 16 x 3 3"> The capacity of the two plates (2 PL 5/16 x 3) tension member is closet to: DELL
10 – 7/8" Bolts Gusset Plate Plate thickness t = ½" 2" b. 2" Tension Member A36 Steel Plate 2" P 12" 2" g I 2" Calculate Tension Capacity 2" of line 1. abcde (A,„) 2. abfcgde (A„) 3. abfgde (A,), and 4. Yielding over Agross An A 3" 3"
A992 steel is used for the tension member shown. The bolts are ¾ inch in diameter. The connection is to a ⅜ inch thick gusset plate. A. Determine the nominal strength based on the gross area. B. Determine the nominal strength based on the effective net area.
Problem 6: Assume that the pieces making up the connection are adequate, and very stiff such that prying forces can be disregarded, and that the nominal tensile stresses on the M20-F2280 bolts govern. The service load shown consists of 25% dead load and 75% live load. Use LRFD. 1 || T = 620 kN Calculate the factored load applied to the connection shown. Calculate the nominal tensile strength of one bolt. How many bolts are required to resist the load? I I I T = 620 kN
For the connection shown, the average shear stress in the 12-mm-diameter bolts must be limited to 220 MPa. Determine the maximum load P that may be applied to the connection. O 164 KN 149 kN O 94 KN O 109 kN O 122 kN
Question 3 Determine the capacity of plate as well as below connection based on Balts (4) in the below Following reactions :- 7 11 A325, $4 þ Bolts use! Use: AISC manual U Moment = 10 kip-67 2 kip (2) Shear (3) Axial 2 kip رب Ź Plate (A 36) 10 " x 10" x ≤ 11 8 HSS. их их nxuxt 4 H² 7
3. Check if the allowable modified tensile strength of bolt group under combined tensile force of Px=225 kN and shear force of Py-600 KN is adequate. (Assume that connected plies are safe against shear tearing out and bearing failure) [all dimensions are in mm] Given Bolts M22 -8.8 Material of Bolts: 8.8 Threads are NOT in plane of shear. Fyb-640 N/mm² Fub-800 N/mm² Fny nominal shear stress of bolt : Fnt nominal tensile stress of bolt : 22=2.0 f required shear stress of bolt : A* Px A+ + 50 100 100 50 + +50+ -$- -150 SECTION A-A -50+