Gear B supplies 15 kW of power, while gears A, C and D withdraw 6 kW, 4 kW and 5 kW, respectively. If the shaft is made of steel with the allowable shear stress of Tmax = 75 MPa, and the relative angle of twist between any two gears cannot exceed 0.05 rad, determine the required minimum diameter d of the shaft to the nearest millimeter. The shaft is rotating at 600 rpm. Shear modulus of steel G = 75 MPa|

Gear B supplies 15 kW of power, while gears A, C and D withdraw 6 kW, 4 kW and 5 kW, respectively. If the shaft is made of steel with the allowable shear stress of Tmax = 75 MPa, and the relative angle of twist between any two gears cannot exceed 0.05 rad, determine the required minimum diameter d of the shaft to the nearest millimeter. The shaft is rotating at 600 rpm. Shear modulus of steel G = 75 MPa|

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.7.12P

See similar textbooks

Similar questions

Gear B supplies 15 kW of power, while gears A, C and D withdraw 6 kW, 4 kW and 5 kW, respectively. If the shaft is made of steel with the allowable shear stress of tallow = 75 MPa, and the relative angle of twist between any two gears cannot exceed 0.05 rad, determine the required minimum diameter d of the shaft to the nearest millimeter. The shaft is rotating at 600 rpm.
The solid steel shaft is supported by frictionless bearings in D and E. This system is connected to a motor that provides 5 kW of power to the shaft while rotating at w = 75 rpm. If A and B gears get 2 kW and 3 kW respectively, determine the minimum shaft diameter. w rotation speed and safety shear stress τem = 35MPa are known and given in the table with your names below.
The gears attached to the fixed -end steel shaft are subjected to the torques shown in fig .The shaft has diameter of (14 mm ).Determine the max shear stress and the angle of twist A relative c .use G=80 Gpa 280 N.m 150 N.m A в 40 N.m 0.4m 0.3m
3. Gear B supplies 20 KW of power, while gears A, C and D withdraw 6 kW, 4 kW and 10 kW, respectively. If the shaft is made of steel with the allowable shear stress of 80 MPa, and the relative angle of twist between any two gears cannot exceed 0.065 rad, determine the required minimum diameter d of the shaft to the nearest millimeter. The shaft is rotating at 800 rpm. 600 mm 600 mm 600 mm
The motor at A delivers 50 hp to the shaft while rotating 25 hp at 1800 rev/min. Each gear removes the power shown in the figure. If the shaft is made of a steel that has an allow- able shear stress of 9 ksi, determine the required diameters, B 15 hp dAB 10 hp dAB, dBc, and dcD, to the nearest 1/s in. d BC dcD E
A shaft drives a gear set that is transmitting 8 hp at 2250 rpm. The diameter of the shaft is 1.75 in. Determine the torsional shear stress developed in the shaft.
2. The solid 50-mm-diameter shaft is used to transmit the torques applied to the gears. Determine the absolute maximum shear stress in the shaft. (Source: R.C. Hibbeler) 250 N-m 75 N-m 325 N-m B 150 N-m 300 mm C 400 mm 500 mm
The steel shaft DF consists of three concentric tubes and is supported by smooth bearings at D and E. It is coupled to a motor at F, which delivers 15 kW of power to the shaft while it is running at 55 rev/ sec. The gears A, B, and C remove 4 kW, 5 kW, and 6 kW, respectively. The shaft is free to turn in its support bearings D and F. Determine the shearing stress developed in segments BC and CE
The gears attached to the fixed -end steel shaft are subjected to the torques shown in fig .The shaft has diameter of (14 mm ).Determine the max shear stress and the angle of twist A relative c. use G=80 Gpa 280 N.m A 150 N.m 40 N.m 0.4m 0.3m Q-2
A solid 14 mm diameter steel shaft is fixed to a wall at E. Torques are applied to gears A, C and D as shown. Determine the maximum shear stress in the shaft and the rotation angle for gear A. G = 80 GPa 40 N•m 280 N m 0.5 m 150 N-m B 0.3 m P. 100 mm 0.4 m (a)
The four gears shown are attached to a steel shaft that is rotating at 2 Hz. Gear B supplies 70 kW of power to the shaft. Of that power, 20kW are used by gear A, 20 kW by gear C and 30kW by gear D. G=83 GPa for steel -20KW JOKN -20kw -30kW 2m 1.5m 1.5m B (a) If a uniform shaft diameter of 125 mm B speci fied, detenmine the angle of rotation of A relative to D. O f segment Co is to be replaced lay a hollaw Shaft with an inside diameter of 80 mm, what is the outside diameter if the stress is not to excced 70 MPa.
A motor drives a shaft at 300 rpm and a power output of 100 kW. The shaft is made of A-36 steel and has diameter 128 mm. There are two gears at B and C and power is transmitted to them equally. The bearing at D can be taken to be frictionless. Calculate the maximum shear stress in the shaft, and the angle of twist of D relative to A. The lengths are 2 m, L2 = 3 m, and L3 = 3.5 m. L₁ = A B 030/ 2021 Cathy Zupke X ↳₂ The maximum shear stress is Tmax= 60.9 X MPa The angle of twist (in degrees) between A and D is A/D 58.2 O C