Gate AB is subject to fluids on both sides as shown. Determine the following parameters considering a unit width (1 m) of the gate. For the water side: (a) A (m²), (b) (m), (C) F (KN), For the glycerin side: (d) A (m²), water Glycerin (SG = 1.26) (e) (m), (f) F (kN), and (g) What is the magnitude net hydrostatic force Ft (KN) on the gate? 1.8 m 1.2 m 2.0 m 2.0 m 1.0 m gate

Gate AB is subject to fluids on both sides as shown. Determine the following parameters considering a unit width (1 m) of the gate. For the water side: (a) A (m²), (b) (m), (C) F (KN), For the glycerin side: (d) A (m²), water Glycerin (SG = 1.26) (e) (m), (f) F (kN), and (g) What is the magnitude net hydrostatic force Ft (KN) on the gate? 1.8 m 1.2 m 2.0 m 2.0 m 1.0 m gate

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

i need the answer quickly
The velocity distribution in a 0.02 m diameter horizontal pipe conveying carbon tetrachloride (specific gravity = 1.59, absolute viscosity = 9.6 x 10-6 Pa sec) is given by the parabolic equation: v(r)=0.01(0.12- r?), where v(r) is the velocity in (m/s) at a distance r in (m) from the pipe center. What is discharge? O a. 3.13 x-8 m3/s O b. None of the mentioned O c. 1.047 x 108 m3/sec O d. 4.97 x 109 m3/sec
the figure below shows a water pipe where a pressure tap is being carried out. At the site, the specific gravity of water Ywater=10,000 N/m^3 and the specific gravity of mercury is UHg=136,000 N/m^3. Find the gauge pressure in pipe A. Where h1=50mm; h2=20mm; h3=30mm; h4=20mm
Q2 : Use the dimensional analysis to find the mistakes in the given equation that is considered as surface area of funnel: Equation = r2 + ur² L Q3:
Include a diagram to show analysis (FBD)
C1 (a). A lubricating oil having the dynamic viscosity of 0.056 poise and specific gravity of 1.17. Calculate (i) the density of oil in kg/m3, (ii) the weight density of oil in N/m3, (iii) the kinematic viscosity in stokes, and (iv) the specific volume in m3/kg. C1 (b). The capillary effect in a glass tube of 2.8 mm diameter, when immersed in (1) water and (2) mercury are 7.7 mm and -3.5 mm respectively. Calculate the value of surface tension in contact with air for water and mercury in N/m. Take, the contact angle for water =0° and mercury =130°. C1(a). (i).the density of oil in kg/m3 C1(a). (ii) the weight density of oil in N/m3 C1(a). (iii) the kinematic viscosity in stokes C1(a). (iv) the specific volume in m3/kg C1 (b). 1.the value of surface tension (water) in N/m C1 (b). 2. the value of surface tension (mercury) in N/m
The rectangular gate is 0.85 cm wide into the paper, h = 80 cm, and z =3.0 m. Answer the questions 3&4 Water Z 4 What is Vertical distance between water surface and the center of pressure (m)? 2.457 2.541 2.713 2.796 2.626 Not listed A B 45°
A vertical gap of 0.1 mm contains a fluid of viscosity (2 Pa.s). A thin metallic plate sheet (0.2 m x 0.3 m) is to be lifted up with a constant velocity of 0.1 m/s through the gap. Find the force (f) given the weight of the plate is 60 N a) If the plate is in the middle of the gap b) If the plate is as shown below 4f 0.3 mm 0.7mm
Calculate the X value since the specific gravity of the square prism-shaped object shown in the figure with a base edge a= 65 cm is γ = 0.94 t/m3, the specific gravity of the oil is γy= 0.77 t/m3.
You are designing a hydraulic lift for an automobile garage. It will consist of two oil-filled cylindrical pipes of different diameters. A worker pushes down on a piston at one end (d = 25cm), raising the car on a platform at the other end (d=?). To handle a full range of jobs, you must be able to lift cars up to 3000 kg, plus the 700 kg platform on which they are parked. To avoid injury to your workers, the maximum amount of force a worker should need to exert is 100 N. What should be the diameter of the pipe under the platform? If the worker pushes down with a stroke 50 cm long, by how much will he raise the car at the other end?
. A buoy is a solid cylinder 0.30 m in diameter and 1.20 m long. It is made of material with a specific weight of 7.90 kN/m³. If it floats upright, how much of its length is above the water. Answer: H = Water y = 9806.6 N/m³ H d = 0.3m L = 1.2 m
The company has opted to purchase a new viscometer for you, as such, you are required by topropose two options for new viscometers. Select two viscometers and explain their operation andconstraints. (P3)b. (P4) Given that you achieved the following results with a U-Tube viscometer:Temperature/ C Time / s40 5760 4180 29100 16Calculate the viscosity at each temperature if the calibration constant is 0.511.d. (M2) Illustrate the results on a graph of temperature vs viscosity and give a briefing on what yourresults indicate, identifying the response of the oil to temperature and explaining anydiscrepancies that may have occurred during the testing.e. (D2) From your testing you discovered that you had a Newtonian and Non-Newtonian sample.Explain to your team what the two terms mean with respect to temperature and shear force onboth samples, giving at least one example of each type of fluid.