gas-turbine power plant operating on an ideal Brayton cycle has a pressure ratio of 8. The gas temperature is 300 K at the compressor inlet and 1300 K at the turbine inlet. Utilizing the air-standard assumptions. 1. determine the internal efficiency with an ideal regenerator of an effectiveness of 100%. 2. compare this efficiency to that given in equation 9-25 3. determine the energy savings with using the ideal regenerator

Q: A gas-turbine power plant operating on an ideal Brayton cycle has a pressure ratio of 8. The gas…

A: GIVEN DATA- A BRAYTON CYCLE GIVEN Pressure ratio = 8 Temprature at Compressor inlet T1=300K Turbine…

Q: If the inlet air is at 80.0°F and the turbine outlet is 2040°F, what is the efficiency of this…

A: Given: Brayton Cycle P1=1 atmP2=5 atmηC=0.65ηT=0.75T1=80 F=299.817 KT4=2040F=1388.7 KTo…

Q: 8.

A:

Q: An engine operating on the air-standard Otto cycle has a 12 % clearance volume, a total displacement…

A: Engine operating cycle = Air-standard Otto cycle Clearance volume Vc = 12 % = 0.12  Total…

Q: Ideal Otto cycle with air as the working fluid has a compression ratio of 9.5. The temperature,…

A:

Q: A Brayton cycle with regeneration using air as the working fluid has a pressure ratio of 7. The…

A:

Q: Task (1) A Brayton cycle with regeneration operates with a pressure ratio of 7. The minimum and…

A:

Q: Your selection was a gas-turbine power plant operating on an ideal Brayton cycle and according to…

A: Given data: The pressure ratio is P2P1=14.77 The inlet temperature at the compressor is T1=350 K…

Q: Brayton cycle with an air-powered regenerator has a pressure ratio of 8. The lowest and highest…

A:

Q: A Bryton power plant is designed to develop a power output of 135 MW when operating at standard…

A:

Q: Required information Problem 09.097 - Modified Brayton Cycle with Two-Step Expansion - DEPENDENT…

A:

Q: Carnot engine is operating on an air standard cycle having a temperature difference of 425C. If…

A: Option c is correct.

Q: The following data was given for a steam power plant operating on the ideal reheat Rankine cycle.…

A: 3-4: Inlet steam at 17.5 MPa and 600 ˚C 6-1: inlet steam at a pressure of 11.16 kPa at a wetness…

Q: An Otto cycle with air as the working fluid has a compression ratio of 10.4. Under cold-air standard…

A: Given, Compression ratio (r)=10.4 Required: Efficiency of the Otto cycle

Q: For a Rankine cycle, decreasing minimum pressure while holding all other parameters constant will…

A: The Rankine cycle contains the following processes: 1-2: Reversible adiabatic pumping 2-3: Constant…

Q: 3-4: Inlet steam at 17.5 MPa and 600 6-1: inlet steam at a pressure of 11.16 kPa at a wetness…

A: Speciic entropy of state 1, State 2 and State 3 is to be found.

Q: With the minimum and maximum pressures set along with the maximum temperature an open feedwater…

A: We are using Fred water heater that means we are using regeneration in the rankine cycle.

Q: The following data was given for a steam power plant operating on the ideal reheat Rankine cycle.…

A: P3=17.5MPaT3=600°CP6=11.16kPax=0.1=1-0.1=0.9 Ist we have to calculate the enthalpy and entropy and…

Q: Consider a regenerative Brayton cycle operating with a pressure ratio of 8, where the air enters the…

A: The pressure ratio is The inlet temperature at compressor is The inlet pressure at compressor is The…

Q: A simple ideal brayton cycle with air as the working fluid has a pressure ratio of 10. the air…

A:

Q: A Carnot power cycle has a high temperature of 1500 K and a low temperature of 500 K. The pressure…

A:

Q: Required information Problem 09.097 - Modified Brayton Cycle with Two-Step Expansion - DEPENDENT…

A: Given data: rp=8T1=0oCP1=110 kPaTmax=T3=1500 K To find:

Q: Required information Problem 09.112 - Brayton Cycle with Regeneration using Variable Specific Heats…

A: Given data, T-s diagram of the given Brayton cycle is Pressure ratio, rp = 7 Minimum temperature,…

Q: If the isentropic compression ratio of a Carnot cycle is 5 and the lower temperature limit of the…

A: Putting all these value in efficiency formula for air standard otto cycle, we got power is equal to…

Q: An ideal Rankine cycle with reheat uses water as the working fluid. As shown below, the conditions…

A:

Q: 1. A power plant working on an ideal Brayton cycle has a pressure ratio of 8. The gas temperature is…

A: Brayton cycle used in gas power plant is a type of power producing device having 4-processes…

Q: generative cycle the inlet conditions are 40 bar and 400°C. Steam is Bleed at 10 bars in…

A: Given:P1=40 barT1=400°CP2=10 barP3=0.8 bar

Q: . A gas turbine uses the Joule cycle. The inlet pressure and temperatur espectively 1 bar and -10°C.…

A: Given:P1=1 bar,P2=P3=7 bar,T1=-10o C or 263 KT3=700o C or 973 Km˙=0.4 kg/sγ=1.4,Cp=1.005 kJ/kg.K

Q: Task (1) A Brayton cycle with regeneration operates with a pressure ratio of 7. The minimum and…

A:

Q: If the mass of the string and the cup are so small that they are negligible, what is the approximate…

A: Solution:

Q: A gas turbine power plant operating on an ideal Brayton cycle has a pressure ratio of 8.the gas…

A: Consider below T-S diagram for the given question: Here, 1 = Inlet of comperessor 2 = Outlet of…

Q: A material has a yield stress of 250 MPa. What tensile forces will be needed to cause yielding if…

A: A=200mm2 Stress=250MPa

Q: 1. At the beginning of the compression stroke, an ideal Otto cycle has an air pressure of 15 psia, a…

A: “Since you have posted a question with multiple sub-parts, we will provide the solution only to the…