From the waveform shown in the figure, determine the parameters of the harmonic voltage u(t) = Umcos(2mft +Po). %3D 0.2 02 04 0.2 0.4 0.6 0. 1. 1.2 14 1.6 1.8 2. Время, мс Answer options: a) amplitude Um=0.3 V; frequency f= 5 kHz; initial phase o=-90 deg. b) amplitude Um=0.3 V; frequency f%3D5 kHz; initial phase po= 90 deg. c) amplitude Um=0.3 V; frequency f=2 kHz; initial phase po=-180 deg. d) amplitude Um=0.3 V; frequency f=1 kHz; initial phase o=0 deg.

From the waveform shown in the figure, determine the parameters of the harmonic voltage u(t) = Umcos(2mft +Po). %3D 0.2 02 04 0.2 0.4 0.6 0. 1. 1.2 14 1.6 1.8 2. Время, мс Answer options: a) amplitude Um=0.3 V; frequency f= 5 kHz; initial phase o=-90 deg. b) amplitude Um=0.3 V; frequency f%3D5 kHz; initial phase po= 90 deg. c) amplitude Um=0.3 V; frequency f=2 kHz; initial phase po=-180 deg. d) amplitude Um=0.3 V; frequency f=1 kHz; initial phase o=0 deg.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Derive Vout in terms of waveform generator.
What is the advantage of using square wave-form as an Input Signal? What is the shape of the outputwhen the input signals are sinusoidal and triangular in shape? (Hint: Use Function generator andOscilloscope to observe the output)
For the below sinusoidal voltage trace displayed by the CRO, the time/cm switch is on 5ms/cm and the volt/cm switch is on 3 V/cm. a) the frequency will bel Hz b) the amplitude will be V.
A schematic design of a full-wave bridge type power supply is given below. Provide the appropriate values for the inductors, diodes, capacitor and resistors, such that the output DC voltage is 7.5 V and the max. output power for the load resistance is 20 mW (percentage error for output voltage and output power is 2%). AC voltage source: Amplitude=311.13, Freq=60, DC offset= 0. For the rectifier part, choose diodes with an appropriate PIV rating. Show all the formulas and computations involved in acquiring the values for the inductors, diodes, capacitor and resistors. • In choosing your Zener diode, consider the output voltage and the output current. Note that the output current should be the minimum Zener current. • For the value of the series resistor RS, choose a lower value for less ripple but always consider the required output voltage. •The ripple voltage peak-to-peak value should be less than or equal to 1% of the required output voltage. Use the formula below for choosing the…
A certain impedance is given by 1012° N. Does the current lead or lag the voltage, and by how many degrees? Fill in the blanks. The current the voltage by
A schematic design of a full-wave bridge type power supply is given below. Provide the appropriate values for the inductors, diodes, capacitor and resistors, such that the output DC voltage is 6.2 V and the max. output power for the load resistance is 20 mW (percentage error for output voltage and output power is 2%). AC voltage source: Amplitude=311.13, Freq=60, DC offset= 0. For the rectifier part, choose diodes with an appropriate PIV rating. Show all the formulas and computations involved in acquiring the values for the inductors, diodes, capacitor and resistors. In choosing your Zener diode, consider the output voltage and the output current. Note that the output current should be the minimum Zener current. For the value of the series resistor RS, choose a lower value for less ripple but always consider the required output voltage. The ripple voltage peak-to-peak value should be less than or equal to 1% of the required output voltage. Use the formula below for choosing the value…
Q.2) Determine all values of resistors and capacitor for the triangular waveform generator whose output alternates between +10Vpeak and -10V peak when the input is a 10-Hz square wave that alternates between +2V and -2V. The input resistance to the generator must be at least 15 kQ. you may assume that there is no de component or offset in the input.
A voltage wave of 250 kHz has a Vmax-5 V and Vmin=-35 V. The duty cycle of this wave is 0.875. This voltage waveform has been applied across a 2.5 µH inductor for a very long time so that steady state has been achieved. Diagrams of the wave parameters and circuit are shown in this figure: L What is the average voltage of this wave? Average voltage = 35 V Voltage (arb, unit) 1.25 Minimum current: -3.5€ Amps 1 0.75 0.5 0.25 0 4.25 05 Have you integrated the wave over full cycle? 4.75 4 -1.25 Vmax 0.5 Vmin What is the average current flowing through the inductor? Average current = 3.56 A 15 Period/s On average, there is no power consumed by the inductor. Have you considered this? What are the maximum and minimum currents that flow through the inductor? Maximum current: 0.50 Amps D= 25 TH TH Have you used the relationship for current and voltage in an inductor? Have you considered the slope of the current wave?
please solve value of Capacitor with 0.1V Ripple. And draw output ripple waveform. Explain it one by one for me thanks..
7 Find the average and effective values of voltage for sinusoidal waveform shown in Figure. Vm = 100 V 2x x14 9714 [Ans: 27.17 V, 47. 67 V]
For the current waveform that shown in Figure below Find:- 1). Average value 2). R.M.S value 3). Form factor Current (A) ha 8 10 12 1-2
Reduce to its simplest form using msop