From the given beam, determine the moment at point A. The unit for Force is in Newton(N) and Length is in meter(m). F=1,645 M-3,887 P-5,992 Note: 1. Input the numerical value of your final answer in the box provided do not include the unit.. 2. Use 2 Decimal Places in your final answer. 3. If your answer is negative, include the negative sign in inputting to the box provided. A 2 m F 3 m M 2 m P 5 3 A 4 2 m 9

From the given beam, determine the moment at point A. The unit for Force is in Newton(N) and Length is in meter(m). F=1,645 M-3,887 P-5,992 Note: 1. Input the numerical value of your final answer in the box provided do not include the unit.. 2. Use 2 Decimal Places in your final answer. 3. If your answer is negative, include the negative sign in inputting to the box provided. A 2 m F 3 m M 2 m P 5 3 A 4 2 m 9

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

NOTE MY ID NUMBER 20-3994-175 ANSWER NUMBER 8 9 10 11 12 - Don’t round off answers unless it is already the final answer. -Final answers must be up to 3 decimal places only. PLEASE INDICATE THE NUMBER IN EVERY ANSWER.
Help me, thank you! List of Surveying Instruments that are used in the field of Civil Engineering. Describe each instrument and put the uses, advantages and disadvantages.
What pieces of apparatus are used for measuring?
The solutions and answers should have minimum of 3 decimals for linear measurements and should be in Degree-Minute-Seconds (2 decimals for seconds) for angular measurement, if not whole number. An engineer is tasked to measure a whole line multiple time. Since the length of the line is significantly longer than the steel tape, the engineer decided to measure the line in three segments. First, the engineer measures a 50m known line using the steel tape and find out that the tape is too long with the observation having only 49.2m. With these values, the correction factor of ???? = 50? − 49.2?. After determining such corrections for future calibration, the engineer measured each segments. The following are the observations: 1st Segment: 46.2m, 46.3m, 46.5m; 2nd Segment: 48.3m, 48.2m, 48.1m; 3rd Segment: 32.3m, 32.6m, 32.4m. Determine the complete expression of the most probable value (together with probable error) of the line.
Question 4 Given that y= 5t3+7 and x =F-5 Find y" when x-6. Express your answer in whole number A Moving to another question will save this response. acer
Q1) Calculate the number of aviation lines if you know that the dimensions of the area 30 x 30 km and the scale 1:20000 and the dimensions of the negative board 25 x 25 cm and side overlap 30%.
A line was measured with a 50-meter tape. If there were 56 rods recorded and end was found to be 24.3 meters, what is the measurement of the line in meters?
HORIZONTAL CURVE: A horizontal curve is designed with a 2500-ft radius. The curve has a tangent length of 450 ft and the Pl is at station 100+ 00. What is the Central Angle of the curve? (Note: Use 1 decimal point for your answer) Ex: 20.4 (Do not encode the units) Just input the elevation. * Your answer Continuation: What is the length of the curve? (Round off your answer to the ones digit. Example: 888) (Do not encode the units) Answer: ft * Your answer Continuation: What is the External Distance? Answer: ft (Note: Use 1 decimal point for your answer) Ex: 20.4 Your answer
4.
Write your solution in paper (manual handwriting) with the following content: Given with figure, Required, Equations, Solution and Final answer/s.
Referring to figure below, a site has been identified for the construction of a basement parking. The spot height levels (in meter) were measured at the intersection of the grid lines of distant 20m x 25m each and the measured data are shown in the figure below. Determine the total volume of ground to be cut or filled of the platform level if the ground is fixed at 20.00m. Using Grid formula
I just need the final answer please