Four forces are exerted on the eyebolt as shown. If the net effect on the bolt is a direct pull of 715 lb in the y-direction, determine the necessary values of T and 0. 30° Assume F₁ = 365 lb, F2 = 245 lb, F3 = 385 lb, p = T F₂ F₁ Answers: T= i D e lb F₁ 3 X

Four forces are exerted on the eyebolt as shown. If the net effect on the bolt is a direct pull of 715 lb in the y-direction, determine the necessary values of T and 0. 30° Assume F₁ = 365 lb, F2 = 245 lb, F3 = 385 lb, p = T F₂ F₁ Answers: T= i D e lb F₁ 3 X

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Problem 12. A plate is used as a bracket and is attached to a column flange as shown in the figure. The loads are factored loads. The eccentricity of the load is a x = 30 mm; y = 75 mm b x = 45 mm; y = 100 mm c x = 150 mm; y = 250 mm d x = 180 mm; y = 125 mm 13. For the connection shown in problem, the resisting moment of the bolts is a 18 kN - m b 20.915 kN - m c 29.25 kN - m d 36 kN - m 14. For the connection shown in problem 12, using elastic analysis the force on the most stressed bolt is a 21.451 kN b 57.051 kN c 91.415 kN d 180 kN 15. For the connection shown in problem 12, the critical bolt is the bolt located at a upper left b upper right c lower left d lower right 16. For the connection shown in problem, determine the diameter of the bolts if A325X bolts are used. a M16 bolts b M20…
A bolt needs to be tightened to a degree that is equal to a moment amounting to 60 N-mm. If a 14-inch cross wrench will be used, how much force should be applied on both ends of the wrench to tighten the bolt? If ϴ = 60 deg, find the following:a)x and y components of 900 lbb)x and y components of 500 lb
show complete work as fast as possible ,Make sure the answer is correct.
Subject: STRENGTH OF MATERIALS (Civil Engineering) Round off to three decimal places
Four forces are exerted on the eyebolt as shown. If the net effect on the bolt is a direct pull of 640 lb in the y-direction, determine the necessary values of T and 0. Assume F₁ = 390 lb, F2 = 230 lb, F3 = 410 lb, d = 35° F T F₁ 0 Ø
Problem 3: Now we will repeat the previous problem using the Cartesian method. Values: FA = 20 N FB = = 30 N ● α = 25° ● Use the Cartesian method to determine... a) the magnitude of the resultant force on the bolt. b) the angle made by the resultant, as measured relative to the positive x-axis. FA α FB
The gear reducer is subject to the couple moments shown. Determine the resultant couple moment and specify its magnitude and coordinate direction angles. M₁ = 60 lb-ft 30° M₂ = 80 lb-ft 45°
Four forces are exerted on the eyebolt as shown. If the net effect on the bolt is a direct pull of 550 lb in the y-direction, determine the necessary values of T and 0. Assume F₁-305 lb, F₂-275 lb, F3-440 lb. = 30° Answers: T- lb 0- i
As you can see on this equipment, an Engineer design a belts/pulley with 0.03m shaft and a shear key. Given are tensile forces of each belts (see figure) and shear key measurements. Find the value of T resulting from that of shear key. 1,500 N 30 mm 120 mm 600 N Shear key (6m x 6mmx 25mm long)
How to solve the attached question step by step
The five-bolt connection must support an applied load of P = 114 kips. If the average shear stress in the balts must be limited to 10 ksi, what is the minimum bolt diameter that may be used for this connection?
A 17-mm-diameter steel [E = 206 GPa; a = 11.5×10-6/°C] bolt is used to connect two rigid parts of an assembly. The bolt length is a = 130 mm. Determine the minimum clamping force that must be provided by the bolt when T₁ = 17°C so that the clamping force it exerts when T2 = 60°C is at least 2.1 kN. a Answer: F₁ = KN