For Va=150 mV, if the circuit given below is analyzed using the detailed model of an op amp (as opposed to the ideal op-amp model). calculate the value of open-loop gain A required to achieve a closed-loop gain within 2 percent of its ideal value. Assume zero output resistance and infinite input resistance for the 250- resistor. 1.4 ΚΩ 250 Ω V₂ of out The value of open-loop gain Amin is[

For Va=150 mV, if the circuit given below is analyzed using the detailed model of an op amp (as opposed to the ideal op-amp model). calculate the value of open-loop gain A required to achieve a closed-loop gain within 2 percent of its ideal value. Assume zero output resistance and infinite input resistance for the 250- resistor. 1.4 ΚΩ 250 Ω V₂ of out The value of open-loop gain Amin is[

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

1) Op-amp limiting factors - Current Saturation U2 Vin R1 OUT OPAMP R2 RLoad The saturation output current for the above op-amp is +/- 15mA. For the following input signals, determine if the output appears as would be expected in an ideal circuit. Include sketches of the output voltage. a) R1 = 100, R2 = 900, an open circuit load, and Vin is 2Vpp triangle wave with zero offset voltage (Vmax 1V, Vmin = -1V) and a period of 2ms. b) R1 = 100, R2 = 900, a 1k load, and Vin is 2Vpp triangle wave with a 1V offset voltage (Vmax=2V, Vmin = 0V) and a period of 2ms. c) R1 = 100, R2 = 900, an open circuit load, and Vin is 4Vpp triangle wave with zero offset voltage (Vmax=2V, Vmin = -2V) and a period of 2ms.
1- Mention any two advantages of Integrated Circuit . 2- For the circuit given below : Vin is a sine wave Vinpp=6 V and Vref=-2.4 V , Assume Vsat=±12V Name the circuit and draw the input and output waveforms . Vin Vref 3- Explain why open-loop op-amp configurations are not used in linear applications? Draw the block diagram of opamp and define the function of each block
QI. A siniscidal voltage waveform with 5 V pk-pk and period of 10 as is applied to the input of the op-amp shown in the figure. The open loop gain is 200000 and the supply voltage is +12 . Draw the input and output waveforms showing the time relationship. Vee
10 V(p-p),1KHz sinusoidal voltage is applied to op-amp input and non-inverting input isgrounded. What is the gain of this op-amp and why?
0.2 Design inverting circuits. an op-amp circuit to produce the output Vo= 8Vi, using both inverting and non-
Assuming an ideal· op-amp's saturation voltage- UsSAT = +15V. For the- circuit in Figure · if u = 3V, the output voltage of op-amp is (404) i 10
3ZF The typical value of the out impedance of an op-amp is a.between 100 Ohms to little less than 1 KOhms b.less than 100 Ohms c.at least 10 percent of the input impedance d.equivalent to short circuit
H.W: Derive the following and draw the circuit. ⚫ The output voltage of the summation Op-Amp. ⚫ The output voltage of the subtractor Op-Amp.
An inverting op amp has Rf= 600kohm and R1= 6kohm. Determine the op amp circuit voltage gain, input resistance and output resistance. Also Determine the output voltage and input current if the input voltage is 0.1 V. Assume op amp to be ideal one.
H: Design OP-Amp eircwt that Poduce an out Put an given by Uo = - ( 4 V,t Uz to.l U3) If u, = 2 sinwt = 5 V and U3 = - 100V sketch the ont Put vo ltage waveform ?
0.3/(5) Marks Derive the closed loop gain of the op-amp circuit illustrated in figure below. Then find the gain when R₁ 10 ΚΩ, R2 5kn, and R3: 15ΚΩ. = = = Vs R₁ R2 R3
In the op amp model above, open-loop gain is 106 and Vcc=12V. Suppose the inverting-input voltage is vn=90μV and the output voltage vo=5V. What is the noninverting input voltage vp (in micro-volts)?