For the vertical wall shown on the left, the oil thickness is assumed to be 0.2 m and its SG is 0.8. Assume the wall and gate width (into the paper) are 2 meters. Draw the pressure diagram. Assume the density of water is 1000 kg/m2 and g = 9.8 m/s2. Oil Determine а. Pressure at the interface between oil and water Water b. Pressure on the hinge С. Pressure at the base of the gate 2.1 m d. Amount of force acting on the gate Hinge е. Location of the force relative from the hinge 2-m-wide 0.8 m gate

For the vertical wall shown on the left, the oil thickness is assumed to be 0.2 m and its SG is 0.8. Assume the wall and gate width (into the paper) are 2 meters. Draw the pressure diagram. Assume the density of water is 1000 kg/m2 and g = 9.8 m/s2. Oil Determine а. Pressure at the interface between oil and water Water b. Pressure on the hinge С. Pressure at the base of the gate 2.1 m d. Amount of force acting on the gate Hinge е. Location of the force relative from the hinge 2-m-wide 0.8 m gate

Name: For the vertical wall shown on the left, the oil thickness isassumed
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: For the vertical wall shown on the left, the oil thickness isassumed to be 0.2 m and its SG is 0.8. Assume the wall and gatewidth (into the paper) are 2 meters. Draw the pressure diagram.Assume the density of water is 1000 kg/m2 and g = 9.8 m/s2.Oil

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1) Determine the Air Pressure at Point A when the other end of the manometer at Point B is open to the atmosphere. 2) If passages at Point B is suddenly closed at 1.5 meters above the mercury surface while the Air Pressure at Point A have already been determined earlier, calculate for the Pressure of Air trapped at Point B. Oil, s=0.87 A Patm Air Br 1.2 m 1.4m Water 1.6 m Mercury
Q4: A tank 25 ft deep and 8 ft wide is layered with 8 ft of oil, 6 ft of water, and 4 ft of mercury. Compute(a) the total hydrostatic force and (b) the resultant center of pressure of the fluid on the right- hand side of the tank.
A cylinder (diameter 4 m) of weight 50 kN is placed on the bottom of the tank as shown and oil and water is poured in left and right side of tank respectively. Magnitude of horizontal force at centre that should be applied on cylinder so that it does not roll is (for unit length) kN. 64m Oil S=0.7 1.2 m Water S=1 0.7m
For the position indicated in the figure, the pressure gauge indicates zero pressure and the piston touches the spring without compressing it. The spring has a constant of 360 KN/m and the relative density of the oil is 0.85. the diameter of cylinder "A" is 0.7 m and that of cylinder B is 0.5 m. What will be the pressure read on the manometer when the spring is compressed 40 cm?
4. Determine the pressure difference between the points at A and B. Take the density of air as 0.03486 kg/ ft^3. (Answer must be in kPa) 0.2 m Air 0.2 m ha - l4 sin 30° Liquid (S1 = 1.2) 30 [h3=l3 sin 30° 0.4 m Mercury (SHg = 13.6) 0.25 m Z-
3
If the wall in following figure is 4 m long, calculate the total force on the wall due to the oil pressure. Also determine the location of the center of pressure and show the resultant force on the wall.
A 10cm x 10 cm x 10cm block of steel (ρsteel = 7900 kg/m3) is suspended from a spring scale. The scale is in Newtons. a. What is the scale reading if the block is in air? b. What is the scale reading after the block has been lowered into a beaker of water and is completely submerged?
can u solve pls #3
خ
None
(Just Question a.) A water filled pipe has water flowing at v1= 5.90 m/s in a section of pipe where the diameter is d1= 20.2 cm and the pressure is known to be P1= 7.00×104 N/m2 above atmospheric pressure. If the pipe carries the water 3.5 meters up hill without any change in diameter, what is the new absolute pressure within the pipe? After flowing up the hill described above, the pipe narrows to 80% of its original radius, what will be the new water velocity (v2) in the pipe? What will be the absolute pressure (P3) in the smaller pipe? a. What is the volume flow rate through the smaller pipe?