For the system shown in figure obtain the positive sequence, negative sequence and zero sequence bus impedance matrices. Data are given in table. T₁ 1 2 G₁ to Coto 4+ Item G₁ G₂ Ti T2 Line 1-2 X¹ X² xº 0.10 0.10 0.05 0.10 0.10 0.05 0.25 0.25 0.25 0.25 0.25 0.25 0.30 0.30 0.50 3 T₂ 4 340 G₂

For the system shown in figure obtain the positive sequence, negative sequence and zero sequence bus impedance matrices. Data are given in table. T₁ 1 2 G₁ to Coto 4+ Item G₁ G₂ Ti T2 Line 1-2 X¹ X² xº 0.10 0.10 0.05 0.10 0.10 0.05 0.25 0.25 0.25 0.25 0.25 0.25 0.30 0.30 0.50 3 T₂ 4 340 G₂

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

1. The single line diagram of a three-phase power system is shown in Figure 1. Select a common base of 100 MVA and 13.8 kV on the generator side. Draw the per unit impedance diagram with new values per unit reactances. G: 90 MVA, 13.8 kV, X = 18% T1: 50 MVA, 13.8/220 kV, X = 10% T2: 50 MVA, 220/11 kV, X = 10% T3: 50 MVA, 13.8/132 kV, X = 10% T4: 50 MVA, 132/11 kV, X = 10% M: 80 MVA, 10.45 kV, X = 20% Load : 57 MVA, 0.8 p.f lagging at 10.45 kV Line 1 =j502; Line 2 = j70 Q j50 2 G M 70 2 Load Fig.1: Single line diagram rele -ele ele rele
Establish Zbus matrix for the system shown in figure below using Direct Method and add the lines in the sequence, 1-0, 2-0, 3-1, 1-2, 2-3 as denoted in the figure?
3) Two generating units have piecewise linear cost functions. Thus, their incremental cost functions are piecewise constant. Their piecewise constant incremental cost functions are listed below. Unit 1: 100 MW < P < 400 MW Р. (MW) dF1(P1) dP 100 - 200 7.8 200 - 400 8.1 Unit 2: 100 MW < P2 < 400 MW dF2(P2) dP2 7.5 8.2 8.3 Р. (MW) 100 - 200 200 - 300 300 - 400 Determine the generation dispatch for a system load of 450 MW.
The sample large power system network data's are given below, The total number of buses is 5 Three-phase short circuit fault subjected at the bus 5 The initial voltage of the faulted bus is 1.0 p.u The Z matrix element Z55 is 0.474 p.u Fault impedance Z= 0.46 p.u Fault current (- )in p.u
What is the Ybus ? voltages and impedances are given per-unit.
7. System Model and Per Unit T1 Line T2 BE 31.25miles 3 Impedance Load R1+jXL-0.1+j0.5 p.u. 30 MVA 30 MVA 13 kV X-0.1 p.u. 14 kV 13/220 kV X-0.2 p.u. 35 MVA * Transformer T2 is composed of "three single-phase" transformers, each rated 40/3 MVA, 132.8:14 kV with a leakage reactance of 0.1 per unit. (a) Fill in the appropriate base values. Gen. G Trans. Ti Line Trans. T: Load New MVA Base New KV Base (b) Calculate the impedance values. Gen G Trans. T1 Line Trans. T2 Load p.u. Impedance
I need the answer as soon as possible
i need ans within 9 minutes with draw happy emoji in the end my best wishes ton
The mathematical relationship between the voltage and current in a J-FET is a ___. a.quadratic function b.All of the above c.sinusoidal d.exponential e.linear function
8
The zero sequence currents of a generator for line to ground fault is j2.4 p.u. then the current through the neutral during the fault is j0.8 True False
pls solve in less than 30 min pls