: For the rigid frame shown, determine the displacements d rotations of the nodes, element forces and reactions. 2000 lb/ft 3 15 ft 10 ft E = 30 x 10 psi A = 5 in. I = 200 in. 45°

Q: show full solution

A: Given data:The state of stress at a point is given by,To determine:The principal stresses, The…

Q: the sketch top, front, and right side isometric below. For the objects shown in sure that your views…

A: According to the details provided in the question we need to draw three projection view of the given…

Q: How much will an air leak cost during three monthes? the hole has a diameter 6.35mm at line pressure…

A: Given  Hole diameter D=6.35 mm Line Pressure P= 690 kPa Electricity Cost  C=7  centskwh Time of air…

Q: If A = Gax + 3a, and B = 8'ax + 2ay-8 az, %3D (a) find the dot product (b) find OAR

A: GivenA→=6i^+0j^+3k^andB→=8i^+2j^-8k^

Q: Consider two infinite parallel plates in length, where the top plate is moving to the right at a…

A:

Q: 2. Draw the sketch of 'Drilling machine' and explain any four parts. Use pencil to draw the neat…

A:

Q: how o create all parts list after the drawing ?

A: Given question: how to create all parts list after the drawing ?

Q: Draw the top view  front view  right side view  on graphing paper please. Put measurents if…

A: Orthographic Projection It is a form of presenting a three-dimensional object into Two dimensional.…

Q: さutてosuう +1 U、ズX ) Given. find dd.? dx

A:

Q: Hi, -26.088 or 333.911 is INCORRECT for Ox please recheck

A:

Q: Sketch the orthographic projection as per the answer arrangement (a) top view (b) side view (C)…

A:

Q: 8. A scale problem : a) Construct a scale of 1/50 to read meters and decimeters and long enough to…

A:

Q: Date Class Review Activity 2-2- Study the drawing below and identify the twelve lines by name,…

A: The lines are method of understanding the CAD diagram of drafts. By observing we can identify the…

Q: Given drawing of a Mechanical component, study the drawing carefully and then using Inventor, AUOB…

A: 1. Create the 3D Model of the part.

Q: create Mind Map for Normalizing (heat treatment process)

A: Normalizing is a heat treatment process, heating a material above the recrystallization temperature…

Q: - Compute A.P.F. for F.C.C.?

A: APF is just the volume of the atoms within the unit cell, divided by the total volume of the unit…

Q: Draw the isometric view of the following object given in orthographic projection.

A:

Q: 11) Define the cornering stiffness.

A:

Q: Draft and annotate the below sketch using AutoCAD Note: colour the hatching lines with different…

A:

Q: Pls use any CAD software to draw the sectional view of the solid attached in the image below.

A: FindWe need to draw the sectional view of the given object using CAD software.

Q: also why is Q/T0 being subtracted in sgen1 while other 2 its being added

A:

Q: Draw the Ts diagram of the whole process

A:

Q: Oil relation between the shear stress and rate of deformation is given in the figure, If the oil…

A: The relation between shear stress and rate of deformation is - τ=μdudyμ=τdudyThe slope of the graph…

Q: Identify Counter-sinking operation from the following drilling operation a. Ob. C. Work stationary O…

A:

Q: To make the 3d sketch for each of the frames which contain the views in the plan

A:

Q: give me 5 explaination why need to do UT and MPI on sample

A:

Q: can make it in Solidwork

A: Given Structure To find 3D model

Q: QUESTION 3 Code for a clockwise circular move to an end point that is 1 inch over in the X direction…

A: consider the following diagram:

Q: Consider the 2D surfaces submerged in a stationary body of water, where the location of the…

A: Option (b) is correct option.

Q: How did you find the value of Patm of value 101.325?

A: How did you find the value of Patm =101.325 kPa?

Q: Given the front and top view create the missing side view.

A: The side view is

Q: Need full accurate RRL .  For both 1. height of sweet potato plants. 2. programable  speed of a…

A: The question is asking for a detailed review of related literature (RRL) on two distinct topics: the…

Q: 4) FIND EGNS FOR VEM DRAW VEM DIAGRAMS 0 200 kit 30

A:

Q: 1. average velocity is correct (-0.75 m/s) but instantaneous velocity (-1 m/s) is incorrect can you…

A: Given :    To find : instantaneous velocity v when t =4 s

Q: Stoker

A:

Q: Project 2: In company that designs road cars and heavy trucks, it important to make the proper…

A: Hi, thank youy for the question! Since we only answer up to 3 sub-parts, we’ll answer the first 3.…

Q: Q// Drow the 5.8.0 and B,m.D yougN

A: The shear force diagram for the beam is

Q: If the shaft is always smaller than the hole, general fit name is Fill in the blank with correct…

A: If the shaft is always smaller than the hole, general fit name is_______________. Answer: D)…

Q: differentiate between caption and turret lathe

A: Capstan and Turret lathe is one of the broad classifications of a Lathe

Forming and Shaping

Metal forming is a category of metalworking process through which the material can be given the desired shape and size by subjecting it to plastic deformation, where the component undergoes bulk deformation process upon application of loads. Unlike the shearing and machining process, the material does not undergo up to a failure point as indicated in the stress-strain curve. Hence, the stresses induced during the forming process are greater than yield strength but less than the failure strength of the material. The process does not lead to the loss of material, so it can be said to be an economical process. During forming, the material is subjected to tensile forces, compressive forces, bending, and shearing loading conditions. The material should possess the property of ductility to undergo the forming process.