For the pulleys system shown below, if each pulley has 80 N weight, answer the following to be the system in equilibrium B Cable 2 Cable 1, 400N 200N The value of load P is

Q: Two cables DAC and ACB are rolled on two pulleys at A and C as shown in Figure 2. applied to the…

A: givenQ=1800Nsystem is shown as below

Q: force members in the bars and state the

A: Given: A struss To determine forces in all members

Q: The following forces are acting on the bracket below. The bracket has a width w of 2 inches and a…

A: The basic criteria for equilibrium is that , there should be no net force or moment on the system

Q: 3. A uniform meter stick of length L = 100.0cm is held in equilibrium by two fulcrums A and B. The…

A:

Q: i. Draw the Free Body Diagrams for pin C, Block A, and Block B. ii. Applied force P on pin C is…

A: Either block moves when the friction can't overcome the horizontal pull

Q: Two farmers are pushing on a gate with forces FA and FB, applied at locations A and B respectively.…

A:

Q: Q2 : The three bars shown in fig are pined at point B which carry a load P and fixed at points A, C…

A: Given: Three bars AB, BD ad CB Cross section of AB=BD=A1 and CB= A2 Young's Modulus of all the bars…

Q: Q2. Determine all forces acting on body A for the system shown in figure 2. Body A weighs 200 N and…

A:

Q: Using the principles of equilibrium of Non-concurrent forces.

A: The free-body diagram is:

Q: A straight pole of length l = 7 ft and weight W = 25 lbf leans against the corner of a wall of…

A:

Q: Solve the following problems completely. Show your FBD with proper label. 1. A smooth sphere of mass…

A: Given data,  m= 10 kg  Radius r= 25 cm = 0.25 m

Q: A rigid bar AD is supported by a ball-and-socket at D, and the two cables are attached to the beam…

A:

Q: The figure shows a kettle bell with a mass of 15kg suspended by three cables. Using the tabulated…

A:

Q: 2. A steel plate structure is held by cable AB and a pin support at C. The plate has a total weight…

A: W = 700 NHole radius, d = 0.04 mIt is asked to find the reaction at C and the tension in the cable

Q: The cords ABC & BD can each support a maximum load of 274 lb. D. 1213 What is the maximum weight of…

A:

Q: The simplest truss consists of two rods and is loaded by the force F. Given: F = 7 kN. Angle α = 50…

A:

Q: Find the tension (T) in the Cord ancd the angle (e) where the motion of block(BI impends doan the…

A:

Q: Determine the components of reaction at the ball-and-socket joint AA using scalar notation.…

A:

Q: A bucket, weighing 375 N, is hung from strings CAD, BA and EA, as shown in the image. Determine the…

A: Given data, Weight of the bucket, W = 375 N Since, CAD is a single string. So, tension in CA and AD…

Q: Equilibrium of a particle: ΣF = 0 .. ΣF = 0 and Fy Find the tensions in the two cables which are…

A: Given data  Mass = 10 kg h= 2.5 m d1= 3.75m and d2=3.75m Find the tension in cable AC and BC

Q: What would be the maximum weight W of the block, shown in the following figure, so that the tension…

A:

Q: The member is supported by a pin at A and cable BC Suppose that r 35 m and the cylinder has a mass…

A:

Q: A weightless boom BD is held in equilibrium by three cables BA, BC and BE as shown in Figure 2. The…

A:

Q: Example Neglecting weight, determine M if the link is in equilibrium. 150 mm M 150 mm 60° 30°

A: Draw the free body diagram for the above problem.

Q: Q1 The frame structure shown below is in static equilibrium. Find the forces acting at pins C and D.…

A:

Q: The system shown in Figure 1 is in equilibrium. Determine the tension force in the cord DA.

A:

Q: Two cylinders are connected by a plank and rest over inclined planes as shown. An external load P is…

A: Two cylinders are connected by a plank and rest over inclined planes as shown. An external load P is…

Q: QUESTION 1 Determine the tension in cables AC and BC, and reaction at the ball and socket joint at O…

A:

Q: Based on the given cage system, where the bars can withstand a maximum tensile force of 5 kN and a…

A:

Q: Q1. Two masses are suspended by the cable system as shown in Figure Q1. The cable BC is horizontal.…

A:

Q: A metal cylinder hangs from the ceiling through three cables attached as shown. If the tension in…

A:

Q: he simplest truss consists of two rods and is loaded by the block. Given: block weight Q = 9,4 kN.…

A: assuming full rigidity we will use lammi's theorem to solve this problem

Q: Consider the antenna in (Figure 1). Figure 300 100 158 1258 100 V 1 of 1 If the tension developed in…

A:

Q: Determine the magnitude of F in a rocker arm shown in the figure below, consider the system is in…

A: Answer: F = 179.2 N For a step-by-step solution have a look through the attached pictures of the…

Q: A flat bar ABCDEF of negligible mass is hinged at A and supported by a roller support at D as shown…

A:

Q: how do i find tension at BC?

A:

Q: Draw the free-body diagram(s) required to solve for the unknowns requested in the problem statement.…

A: Given: The load intensity, w = 200 N/m

Q: A straight, uniform bar weighing 60lb rests in a horizontal positon between two frictionless slopes.…

A:

Q: 2. The structure is connected by a pin joint at point A and by a cable of length L at points B and…

A: The free-body diagram of the above structure is given as, Apply force equilibrium in the vertical…

Q: 2.15. In the accompanying figure M represents an instrument which is packed in a box B with springy…

A:

Q: PROBLEM 1: Determine the tension in each cable and the components offorce reaction at D needed to…

A: The objective of this problem is to find the tension in each cable and the components of force…

Q: Find the forces in the cables AB, BC, CD, DE, and force in the spring CF in terms of P. (a is an…

A:

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.