For the inverted slider crank linkage shown below, the input link is OA, the output link is CB and the coupler link is AB. The link lengthsare: a = 40 in., c = 30 in. and d = 60 in. The values of 02 = 70°, 03 = 171.13° and 0, = 81.13°. The angular velocity of link2 w2 = 10 rad/s CCW.the angular velocity of link 4,the angular velocity of link 3 and velocity of slip are:Select one:O a. Wa = -1.5 rad/s; wa =-1.5 rad/s; b = 437.4 in/sb. wa = -7.51 rad/s; wz =-7.51 rad/s; b = -320.4 in/sO c. Wa = -1.5 rad/s; w3 =-1.5 rad/s; b = -320.4 in/sO d. wa = 1.5 rad/s; wa =1.5 rad/s; b = 320 in/s

Answered: Image /qna-images/answer/4cc03850-e29f-4a55-afd3-ba0c9435f198.jpg

For the inverted slider crank linkage shown below, the input link is OA, the output link is CB and the coupler link is AB. The link lengths are: a = 40 in., c = 30 in. and d = 60 in. The values of 8, = 70°, 8g = 171.13° and 0 = 81.13°. The angular velocity of link2 wz = 10 rad/s CCW.

For the inverted slider crank linkage shown below, the input link is OA, the output link is CB and the coupler link is AB. The link lengths are: a = 40 in., c = 30 in. and d = 60 in. The values of 8, = 70°, 8g = 171.13° and 0 = 81.13°. The angular velocity of link2 wz = 10 rad/s CCW.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

theta O = 55 The link length and value of O2 for some four bar linkage are defined below, (drive link =4.2 cm , coupler link =5.9 cm , follower link = 5.9 cm, fixed link= 6.85 cm 1. draw the linkage to scale and graphically find all possible solution (both open and cross) for 03 and O4 2. If w = 2 rad /s (CCW) find the angular velocity for bar 3 and 4 3.if a= 5 rad/s? (Ccw) find the normal and tangential acceleration for link 3 and 4
The link length and value of O2 for some four bar linkages are defined below, (fixed link =12 cm, drive link =5 cm, coupler link = 10 cm, follower link= 8 cm) 1. draw the linkage to scale and graphically find all possible solution (both open and cross) for 03 and O4, analytical . 2. If w = 2 rad /s (CCW) find the angular velocity for bar 3 and 4 3.if a= 5 rad/s² (CCW) find the normal and tangential acceleration for link 3 and 4
1. Find a combination of link lengths where motion of a point on output link is one quarter of a circle. 2. Find the value of all 0, 0, 0, and y in open and close configuration Read the value of link lengths and the input angle 8., then use the formulae given below to calculate the value of unknowns 03, 0, and y K₁ = = K₂= d K2 K3 = a²-b²+c²+d² 2ac A = cos 0₂ - K₁ - K₂ cos 0₂ + K3 B = -2 sin 0₂ C = K₁ (K₂ + 1) cos 02 + K3 -B± √B²-4AC 2A 0412 = 2tan-1 d K₁ = — K5 = c²d²a²-6² 2ab D = cos 0₂ - K₁ - K4 cos 0₂ + K5 E = -2 sin 0₂ FK₁+ (K₁ - 1) cos 02 +K5 0312 2 tan-1 (-E± -E± √E²4DF 2D Y = 04-03
2. For the crank-slider type linkage shown, you are given that link lengths |ZA| = |AZ| = 10 cm, |BA| = 20 cm. Calculate the angle LZBA, and the distance |BZ|, when the angle of of the crank with respect to the ground LBZA = 45°. What is the length of the stroke of the slider (distance between extreme positions of joint B)? B
A general fourbar linkage configuration and its notation are shown in Figure below. The link lengths, coupler point location, and the values of 02 and w2 for the same fourbar linkages as used for position analysis in Chapter 4 are redefined in Table below. For the row c, draw the linkage to scale and Using an analytical method calculate w3 and w4 and find the velocity of point P. find the velocities of the pin joints A and. RPA Y B 4 03 04 02 1 02 FIGURE P6-1 Configuration and terminology for the pin-jointed fourbar linkage of Problems 6-4 to 6-5 TABLE P6-1 Data for Problems 6-4 to 6-5† Row Link 1 Link 2 Link 3 Link 4 02 Rpa 83 02 a 2 7 9. 30 10 30 7 9. 8 85 -12 9 25 3 10 8 45 -15 10 80
A general fourbar linkage configuration and its notation are shown in Figure below. The link lengths, coupler point location, and the values of 02 and w2 for the same fourbar linkages as used for position analysis in Chapter 4 are redefined in Table below. For the row c, draw the linkage to scale and Using an analytical method calculate w3 and w4 and find the velocity of point P. find the velocities of the pin joints A and. RPA AY 2 04 02 04 FIGURE P6-1 Configuration and terminology for the pin-Jointed fourbar linkage of Problems 6-4 to 6-5 TABLE P6-1 Data for Problems 6-4 to 6-5† Row Link 1 Link 2 Link 3 Link 4 02 02 Rpa 83 6. 2 7 30 10 6. 30 b. 9 3 8 85 -12 9. 25 10 6. 8 45 -15 10 80 O73
Position Analysis of the crank-slider linkage. The link length and offset for a fourbar slider-crank linkage are: link 2= 3.5, link3= 10, offset=1. Find both open and crossed solutions for angle theta3 and slider position, d, as driver makes a complete revolution.construct graphs to describe how the slider and theta3 varies as theta2 makes the entire revolution.
The general linkage configuration and terminology for an offset fourbar slider-crank linkage are shown in Figure below. The link lengths and the values of 02 and w2 are defined in. For the row(s) b and c, find the velocities of the pin joints A and B and the velocity of slip at the sliding joint using an analytical method. Draw the linkage to scale and label it before setting up the equations. Link 3 Offset 04 = 90° Link 2 02 Slider position d TABLE P6-2 Data for Problems 6-6 to 6-7† Row Link 2 Link 3 Offset 02 1.4 4 1. 45 10 2 6. -3 60 -12 3 8. -30 -15
A general pinjointed fourbar linkage is shown in the figure below. It has the followings The link lengths are L1 = 8.50 in., L2 = 3.00 in., L3 = 5.00 in. and L4 = 4.50 in. The values of 0, = 0, 02 = 60°, and 04 = 119°. The angular velocity of link2 w2 = 10 rad/s CCW. L4 L2 02= 60° @2 B. Ao O = 0° Figure 5.32 Problems 5.3 and 5.4 The angular velocities of link 3 w3 and and link 4 w4 are: Select one: O a. w3 5.29rad/s CW, w4 = 6.14 rad/s CW O b. w3 = 3.94 rad/s CCW, w4 = 4.8 rad/s CCW O c. W3 5.29 rad/s CW, w4 = 4.80 rad/s CCW O d. w3 = 3.94 rad/s CCW, W4 = 6.14 rad/s CCW
Problem 4-6a The link lengths (a, b, c, d) and the value of 2 for a crank-rocker linkage are defined as 2, 7, 9, 6, 30°, respectively. Draw the scaled linkage. Find all possible solutions (both open and crossed) for angles 03 and 04 graphically. Орen B A LNCS 4 a GCS र 4 4" Crossed (This is not the scaled kinematic diagram.) Problem 4-7a Repeat Problem 4-6a except solve by the vector loop method.
1. Kinematics Review: For the linkage shown below, find the asc and aco at the instant shown if aAB is 2.5 rad/s counter clockwise. 250 mm OAR = 5.5 rad/s 40° B 300 mm 400 mm 70° D.
3. Design a quick return mechanism with 120 cm stroke, time of forward stroke is 1.2s, return stroke time is 0.4s, fixed link length of 25 cm and driving crank length of 40cm. Determine a.Range of values of L2 b.a and B cộ1 and 2 d.Actual value of L2