For the given circuit, determine the total impedance, total current and total phase angle. C2

Q: BJT vs FET

A: Following are the points of difference between BJT and FET: BJT stands for Bipolar Junction…

Q: Briefly in your own understanding explain attenuation in electrical engineering.

A: Attenuation literally means the loss. Generally, in electrical engineering we deal with the signals…

Q: Define Ohmic region of FET characteristics and Write down the relation between VGS and ID?

A:

Q: 3)- a)- What are the differences between doping and alloying? b)- What is the importance of lattice…

A: Here I have solved it.

Q: Draw the block diagram of digital Multimeter and explain the measurement of D.C voltage

A: Digital multi meter is a measuring device which is used to measure AC and DC voltages, AC and DC…

Q: Which one of the following needs less repair than other resources? a. Wind O b. OTEC O c. Hydro…

A: Among all the renewable energy sources hydro power plant needs less repair so option c is correct…

Q: Write about the applications of electric fan

A:

Q: QI Define lcno and leao. How are they different? How are they related? Are they typically close in…

A:

Q: The total turn ON time of SCR is 24 . If the sum of delay and spread time is 19 , the rise time of…

A: The solution can be achieved as follows.

Q: Draw the architecture of SAP1 & SAP2 and write down the difference between them.

A: The architecture of SAP-1 Architecture of SAP-2

Q: What is the value of frequency of dc

A: The number of times a repeated event occurs per unit of time is known as frequency.  It's also…

Q: The resistance of 250 x 103 ft. of copper wire (pno - 10.36 (cmil-A)/ft.) is found to be 25.9 ohm,…

A:

Q: For the cct. Shown below calculate (for charging phase and discharging phase) (T) Write the equation…

A: Step 1:Step 2:Step 3:Step 4:

Q: What will be the charge and mass of an electron? I am stuck. Please help. Will give good feedback.

A: Electrons are negatively charged particles and they revolve in elliptical orbits around the atomic…

Q: Convert n- cmil W-U of foot

A: Given unit  Ω-cmilfoot

Q: Q8. Write down the names of Fabrication steps and explain the lithography process briefly.

A:

Q: POWER SISTEMS hlgh voltage technlque t is possible to measure pulsed (AND ANSWER THE SAME QUESTION…

A: The data are as:  Ed = 30 kV / cm2 ;  k = 0.9

Q: The total turn ON time of SCR is 21 . If the sum of spread and rise time is 19 , the delay time of…

A: total turn on time of SCR = delay time + rise time + spread time therefore delay time  =turn on time…

Q: Mention atleast three practical application where, ASK FSK and PSK techniques are used. subject is…

A: A digital modulation technique uses digital signal for modulation of carrier signal. ASK stands fo…

Q: 7) The following readings are obtained in the measurement of an inductor: 1.003,0.998, 1.001, 0.991,…

A:

Q: 20. (SP)) (S) performs: a. PUSH S b. РОP D c. None

A: The given instruction is: SP←S

Q: For controlled half wave rectifier, R=35ohm, f=50Hz and Vm=280V and a=0,5 rad. Calculate the power…

A:

Q: Plot x[J and xBn-3]

A:

Q: is the simplest way of producing a source of lower EMF from a source of higher EMF.

A:

Q: 10 14 20 15 2. A 1290 16 C D 11 V 1Ω 13. 5Ω 10V 13 N Dr. Ben Blalock asks that you solve for the…

A:

Q: QUESTIONS 1. Define maximum power point of a solar module. 2. Explain the importance of maximum…

A: A solar module, the solar panel is a single photovoltaic that is an array of connected solar cells.…

Q: Write the report on “Increase of fluorescent lamp and power factor”

A: Fluorescent lamps: Fluorescent lamps, often known as fluorescent tubes, are low-pressure…

Q: A transistor is used as a switch and the waveforms are shown below. The parameters are given as…

A: Given  Transistor as switch and waveforms as shown  Vcc=200 vVCE(sat)=1 vICS=100 AICEO=1 mArise time…

Q: Please write my name on the sheet.                    My name is Zaid Nasser Khayat

A: As per guidelines of Bartleby we are unable to write you name

Q: your take on the FSF and what it entails.

A:

Q: 1.17 Test data from four components are given below. Each test consists of a complete traversal from…

A:

Q: 1. How does speaker convert electrical energy to sound energy? 2. How does microphone convert…

A: Solve the first question, unless the student has asked for a specific question to be solved, subject…

Q: a brief reflection on ELECTRICAL MEASUREMENT UNITS

A: Measurement is the act of finding an unknown physical quantity by using a standard quantity. The…

Q: What is the radius of a copper cable having resistance of 10 ohm and length of 10 km. Assume the…

A: Given data, R=10 ΩL=10 kmρ=1.7×10-8 Ωm

Q: please write details about Arduino or ESP8266

A: ESP8266S plant irrigator : We can built a smart plant irrigation system using ESP8266S and EasyIoT…

Q: Mention Factors determining the size and the direction of the generated emf

A: Factors determining the size and the direction of the generated emf are follows-

Q: mention at least three practical application where,ASK,FSK and PSK techniques are used. Subject is…

A: ASK, FSK and PSK are types of digital modulation techniques, digital modulation techniques have…

Q: What is thte type of signal used in television? a. R3E b. B8E c. F3E c. C3F

A: Choose the correct option What is the type of signal used in television?

Q: explain in detail the static and dynamic characteristics of instruments

A: To choose the one most suited to a particular measurement application, we have to know the system…

Q: four parts are selected randomly and without replacement, what is the probability they are all from…

A: Here it is asked to find the probability with the informations given. Here properties of probability…

Current Division Method

The generalized current divider formula is given by the following relation below,