For the following beam: Determine • Maximum deflection of the beam in terms of w, L, E, and I. • The rotation of point B, if w-10 kN/m, L= 5 m, E= 75 GPa, and I= 4x10 mm*. • The minimum moment of inertia (I) so that the maximum deflection in the beam doesn't exceed (Amax =), if w= 20 kN/m, L= 6 m, E= 200 GPa. 360 B

For the following beam: Determine • Maximum deflection of the beam in terms of w, L, E, and I. • The rotation of point B, if w-10 kN/m, L= 5 m, E= 75 GPa, and I= 4x10 mm*. • The minimum moment of inertia (I) so that the maximum deflection in the beam doesn't exceed (Amax =), if w= 20 kN/m, L= 6 m, E= 200 GPa. 360 B

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Give the weighted mean of each factor. Show solution properly.
Problem 6: Non-linear Regression Model The total time needed to bring a car to stop after the driver perceives danger is the reaction time plus the braking time. Reaction time is the time between the perception of danger and applying the brakes, and braking time is the time for stopping after applying the brakes. The table below gives the stopping distance d (in feet) of the car traveling at speeds v (in miles per hour) from the instant of danger perception. a. Fit a least squares 2nd degree polynomial of the form d = a, + a1v + a2v² b. Estimated when v = 45 mph d V ft mph 20 54 30 90 40 145 50 210 60 305 70 400
Give me two (2) example with complete solution of Linear Regression.
Q2) A parachutist of mass 60 kg jumps out of a stationary hot air balloon. Use numerical method to plot the velocity-time relationship and compute the terminal velocity. The drag coefficient is equal to 12 kg/s. Employ a step size of 4 s for the calculation. Repeat the solution by using Analytical method for five steps only. Based on your results, discuss which method is more exact?
answer a and b no handwritten
7.7 Read and Analyze the sample problems given. Give a thorough analysis stating what type of situation the author dealt with, how the problem was solved, the assumptions that the author considered in solving the problem, and why where these assumptions were made. 5 sentences are more than enough in this for me to learn. Thank you! note: This is not a graded question, this is only to know the explanation; to know its concept.
3.) You are assigned to measure in seconds the arrival of 15 vehicles at a certain point. You observed the arrival of these vehicles in 2 minutes 15 seconds (135 seconds). The arrival of each vehicle in seconds is shown below: vehicle no. Arrival in seconds 1 1.96 2 4.76 3 7.05 4 40.86 44.35 47.58 7 55.64 8 57.38 63.75 10 66 11 68.71 12 73.77 13 98.87 14 125.42 15 128.56
AS3. NO4. DATA ANALYSIS
ESSAY. List down or enumerate what are asked for in each number. 1. What are the do's and don'ts in sampling distribution? 2. Difference between prediction and tolerance interval. 3. Differentiate null and alternative hypothesis. 4. Difference of simple linear regression from correlation 5. Difference of CRD and RCBD
With FBD and Solution pls refer to the second picture if the answer is in the choices one of those 4 answers is correct
Using the data below, compute for the most probable value, individual residual, probable error of any single measurement, and the relative precision of the mean. Look for: most probable value individual residual probable error of any single measurement relative precision of the mean
Example -Homework The cumulative distribution function for the random variable X is given by x4 Calculate P(2 < X <3).