For the figure shown, a 250-lb bar AB is supported by N-in. diameter cable CD and pinned at B. The bar carries a load of 700- st lb. 10. Determine the reaction at point B. 11. Determine the normal 700 stress in cable CD. 12. What is the shear stress at pin B assuming it is double shear? Pin diameter is in.

For the figure shown, a 250-lb bar AB is supported by N-in. diameter cable CD and pinned at B. The bar carries a load of 700- st lb. 10. Determine the reaction at point B. 11. Determine the normal 700 stress in cable CD. 12. What is the shear stress at pin B assuming it is double shear? Pin diameter is in.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The bell crank shown is in equilibrium. (a) Determine the required diameter of the connecting rod AB if its axial stress is limited to 120 MPa. (b) Determine the shearing stress in the pin D if its diameter is 20 mm. B 30° 260 mm- 180 mm A 3. C D 140°. DOUBLE 28 KN SHEAR
asap please thank you
A 16-mm-diameter steel [E = 200 GPa] rod (2) is connected to a 50- mm-wide by 8-mm-thick rectangular aluminum [E = 70 GPa] bar (1), as shown in Figure PP5.3-2. Determine the force P required to stretch the assembly 3.00 mm. (1) 0.45 m Answer in kN rounded-off to 2 decimal places B 1.30 m Figure PP5.3-2 I
Rigid bar ABC is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 7 mm, and it is supported by double- shear pin connections at B and D. The pin at bracket A is a single-shear connection. The pin at B is 7 mm in diameter. Assume a = 640 mm, b = 320 mm, h = 400 mm, and 8= 55°. If the normal stress in tie rod (1) cannot exceed 200 MPa and the shear stress in pin B cannot exceed 100 MPa, determine the maximum load Pmax that can be supported by the structure. D (1) a B KN h
I. N • O P M E;Y7 Z H.W. for fatigue stresses... Q1) In Fig.(1), the shaft is subjected to a reversed load P = (2700 to - 900) N. Find the length (L), if the stress at the fillet equal to the half stress at the center. de6.25 62.5 -O- 50 -375 375 Fillet Fillet All Dimensions in mm Center Fig(1) Q.) In Fig.(2), the shaft is subjected to reversed loads, F = 7 2700 N and P = F 1350 N, where these two loads vary at the same time. Find the required length (L), if the stress at the fillet equal to the stress at the center. F 2700 N P.1350 N P.1350 N 50 62.5 1500 - - Fillet Center Fillet Al Dimensions in mm Fig(2) Q.) In Fig.(3), the shaft is subjected to reversed loads, F = F 2700 N and P = F 1350 N, where these two loads vary at the same time. Find the diameter (d), if the stress at the fillet equal to the stress at the center. F- 2700 N * 10 P.+1350 N P-1350 N d. 1.6 d 500- - 1500 - 500 Fillet Center Fillet All Dimensions in mm Fig(3) Q.) In the Fig.(4) shown below, a machine member is…
A truss system carries a suspended 900 kg-Crate at A. The cross-sectional areas are 120 mm² and 150 mm² for tensile and compressive members, respectively. Indicate Tor C. a. What is the axial stress at member AB? b. What is the axial stress at member BC? C. What is the axial stress at member CD ? cable D WEI B 12m 70° 12m 75m с A
5-83 The A-36 steel shaft is made from two segments: AC has a diameter of 0.5 in. and CB has a diameter of 1 in. If the shaft is fixed at its ends A and B and subjected to a uni- form distributed torque of 60 lb in./in. along segment CB, determine the absolute maximum shear stress in the shaft. 5 in. 0.5 in. 20 in. 60 lb-in./in. 1 in. B Prob. 5-83