For the engineering stress-strain curve, a) Read the value of Ultimate Tensile Strength, UTS. b) In order to find Yield Strength, Y, draw a line parallel to the elastic region starting from a strain of 0.2%. The yield strength is the vertical coordinate of the point where this line you have just drawn intersects with the stress strain curve. Report the values you have measured in the below table.

For the engineering stress-strain curve, a) Read the value of Ultimate Tensile Strength, UTS. b) In order to find Yield Strength, Y, draw a line parallel to the elastic region starting from a strain of 0.2%. The yield strength is the vertical coordinate of the point where this line you have just drawn intersects with the stress strain curve. Report the values you have measured in the below table.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Case Study Determine Properties from Tensile Test Data A cylindrical specimen of stainless steel having an initial diameter of 12.8mm and initial length of 50.8mm is pulled in tension. Use the data provided below to a) Plot the data as engineering stress versus engineering strain using excel or similar software. b) Compute the modulus of elasticity. c) Determine the yield strength at a strain offset of 0.002. d) Determine the tensile strength of this alloy. e) What is the approximate ductility, in percent elongation? f) Compute the modulus of resilience. Load (N) Length (mm) 50.800 12,700 25,400 38,100 50,800 76,200 50.825 50.851 50.876 50.902 50.952 89,100 92,700 51.003 51.054 102,500 107,800 119,400 128,300 149,700 159,000 160,400 159,500 151,500 124,700 51.181 51.308 51.562 51.816 52.832 53.848 54.356 54.864 55.880 56.642 Fracture
a.) determine average normal strain along AC after load has been applied. b.) determine average shear strain at A relative to x and y axis (gamma xy =) c.) determine average shear strain at point C relative to the x and y axes after deformation (gamma xy)
A mild steel specimen of Young's Modulus 205 GPa is subjected to a tensile test in a laboratory. The following data are obtained. a) Initial length of the Specimen = 362 mm; b) Initial diameter of Specimen = 19 mm; c) Yield Stress = 123 N/mm2; d) Ultimate Stress = 225 N/mm2; e) Fracture Stress = 190 N/mm2; g) % of Elongation = 56 %; h) % of Reduction in Area = 29 %. i) The elongation of the specimen at load 83 kN (in mm) ii) Load at yielding (in N) iii) Maximum load (in N) iv) Final Length (in mm) v) Final Diameter (in mm)
2. A 10 mm diameter cylindrical specimen of an aluminium alloy is loaded in uniaxial tension in a testing machine. a) If the specimen begins to yield at a load of 30 kN, what is the yield stress of the material? b) At the point where yielding begins, the measured increase in length between two points initially 50 mm apart is 0.27 mm. At what strain does yielding occur? c) If the load-deflection curve is linear up to the yield point, what is the elastic modulus of the material? d) If the diameter of the specimen was reduced by 18 um at the yield point, what is the Poisson's ratio of the material? [ans.: (a) 382 MPa; (b) 5.4E-3; (c) 70.7 GPa; (d) 0.333]
My last attempt. I will rate accordingly with multiple votes. please do it correctly.
When an object is placed underwater, the pressure on the object is subjected to uniform stress on all sides. a) define volume strain, the bulk modulus, compressibility, and the relationship between the bulk modulus and compressibility. b) A 100 litre volume of liquid is subjected to a 2000 psi increase. If the compressibility of the liquid is 5 x 10-5 per atm, find the bulk strain and absolute decrease in the volume of the liquid c) explain the concepts of shear stress and shear strain? could these concepts be applied to the fluid problem above?
15. Given the following data, plot the stress-strain curve for this tensile steel specimen. The gage length of the specimen is 2.0". The cross sectional area is 0.195 in². Use the diagram that you plot to determine: a.) The Modulus of Elasticity b.) The Yield Stress c.) The Ultimate Stress LOAD P (pounds) Deformation (inches) 0.0000 3000 0.0007 0.0017 0.0025 6000 9000 12000 14000 0.0036 0.0044 15000 0.0060 0.0100 16000 17000 0.0250 0.2000 0.4000 18000 12000* rupture occurred. 2.
Ql- mm ,length 40 mm. The final diameter 18 mm and length 45 mm. Draw the force-extension diagram and determine the following : a) Ultimate tensile strength, c) Modulus of elasticity, d) Percent elongation and e) Percent reduction in area. The following data collected from tensile test of a metal bar diameter 20 b) The fracture strength, Force - kN 75 90 | 105 120 131 125 110 25 50 4.7 Extension-mm 0.02 0.04 0.06 0.20 - 0.60 1.60 3.00 4.0 Fracture
upper leg muscle 9 cm in radius). 2) Don't ever try the acorn diet, its nuts. In the tree diagrammed here, a force of 800 N is exerted at the tip of the limb (equivalent to the weight of "800 apples). The limb is circular in cross-section and 2 m long with a tip radius of 3 cm a base radius of 10 cm. The radius increases linearly from the tip to the base. Plot the tensile stress at the top of the limb along its length. Where along the length would you expect the limb to break? M. X. Lo Y
Solve it quickly please
Mechanical Engineering The fatigue strength limit Sn (n = 106) of a steel part is 112 MPa and its ultimate tensile strength (Sy) is 385MPa. Adopting Ct = 1, and S103 = 0.9 * Su* Ct, determine: (Use two decimal places in the answers), (* is multiplication signal): a) The fatigue strength (in MPa) corresponding to a life of 40000 cycles. b) The average life in cycles that this part would last if subjected to an alternating stress of 170 MPa due to bending.
A copper specimen of Young's Modulus 122 GPa is subjected to a tensile test in a laboratory and the following data are obtained. a) Initial length of the Specimen = 363 mm; b) Initial diameter of Specimen = 10 mm; c) Yield Stress = 128 N/mm2; d) Ultimate Stress = 212 N/mm2; e) Fracture Stress = 180 N/mm2; %3D g) % of Elongation = 44 %; h) % of Reduction in area = 38 %.