For the circuit of figure below:a- Calculate Avs = Vo/Vs.b- Determine fHi and fio.c- Determine the High-cutoff frequency.V,VGSQ = -1.9 VIDQ = 2.8 mACwi = 4 pFCwo = 8 pFCgd=9 pFCgs = 14 pFCds = 4 pF1.5 kf20.05 µFHH3.3 MS2+10 VwwwD+S680 22.4 kQVd=aHH0.05 µFIpssVp = -4 V10 mA+100 µF4.8 ΚΩ

Answered: Image /qna-images/answer/79625145-3b05-4e44-8d33-9eb53de86f6d.jpg

For the circuit of figure below: a- Calculate Avs = Vo/Vs. b- Determine fHi and fio. c- Determine the High-cutoff frequency. VGSQ = -1.9 V IDQ = 2.8 mA Cwi = 4 pF Cwo = 8 pF Cgd=9 pF Cgs = 14 pF Cds = 4 pF 1.5 kf2 0.05 µF Q 3.3 ΜΩ +10 V D + 680 Ω S 2.4 k Va= HH 0.05 µF Ipss Vp = -4 V 10 mA + 100 uF 4.8 ΚΩ

For the circuit of figure below: a- Calculate Avs = Vo/Vs. b- Determine fHi and fio. c- Determine the High-cutoff frequency. VGSQ = -1.9 V IDQ = 2.8 mA Cwi = 4 pF Cwo = 8 pF Cgd=9 pF Cgs = 14 pF Cds = 4 pF 1.5 kf2 0.05 µF Q 3.3 ΜΩ +10 V D + 680 Ω S 2.4 k Va= HH 0.05 µF Ipss Vp = -4 V 10 mA + 100 uF 4.8 ΚΩ

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Design with IC ‘555 and a capacitor of 9 uF: Monostable to get signal period=7 Astable to get frequency=2 Constraints: Use any resistor to be between 1K and 50K.
Find the system transfer function H(s) = Vout/Vin.
3. Show how a series RLC filter, its type depends on the output voltage terminal as follows: Low pass filter the output voltage across ... High pass filter the output voltage across . Band pass filter the output voltage across Band reject filter the output voltage across ...... ......... ........
A step up dc/dc converter has input voltage Vs = 9 V, the average output voltage Va = 15 average load current lg = 0.8 A. The switching frequency is f = 20 kHz, inductance is L = 0.3 mH and the parallel capacitance is C = 0.44 mF. Which one is the ripple voltage of filter capacitance AV. ? O 26.36 V O 56.36 V O 46.36 V O 36.36 V
The circuit in Figure 1 represents the circuit model of an interference path from source vin to the 10 MQ load resistance at vout- C1 C2 1 pF 1000 pF R V in out 10 MQ Figure 1. Interference modeling a) Determine the transfer function H(f) = vou/Vin from vin to vout- b) Determine the output magnitude vout when Vin is a 170V pk sine wave at 60HZ c) Determine the output magnitude vou when vin is a 1V pk sine wave at 1 MHz
Determine Rc and Rg for a fixed-bias configuration if Vcc = 12 V, B = 80, Icq= 2.5 µA and VCEO = 6 V. Use the standard values.
*:Choose the useful and usefulness terms in filters design Usefulness term Useful term Response curve Bandwidth Heat Gravity
In the circuit below, what is the closed loop gain and the width of band? What is the AC output voltage at 100 kHz? Vin 25 mVp p-p Vcc +15 V LF157A VEE -15 V R₁ 3 ΚΩ R₁ 150 Ω Vout
Q3/ Determine the centre frequency, maximum gain, bandwidth and type filter for the circuiting figure. 1 kOhm 0.022 UF HH 0.047 uF 0.047 UF 1 kOhm 1 kOhm Vo HH HH 560 Ohm 560 Ohm 0.022 UF 1 kOhm 1 kOhm Kohm
Answer the question:
A balanced modulator has a 3 MHz carrier input and a modulating signal input of 1.5 kHz. To pass the lower sideband, what will be the filter center frequency in MHz?
Q2/ Determine the centre frequency, maximum gain, bandwidth and type filter for the circuiting figure. 1 kohm 0,022 UF HH 0.047 OF 0.047 uF V V₂ HH 1 kOhm 1 kohm HH Vo 560 Ohm 1 ohm 560 Oh 1 kOhm 1 kohm THI 0.022 UF