For the beam loaded as shown, use the method of superposition to determine the deflection of the beam at end A. Assume the following values: El = 2.8 × 104 kN.m² (constant for entire beam) L = 15 m w = 56 kN/m Answer: VA = i B W mm L

For the beam loaded as shown, use the method of superposition to determine the deflection of the beam at end A. Assume the following values: El = 2.8 × 104 kN.m² (constant for entire beam) L = 15 m w = 56 kN/m Answer: VA = i B W mm L

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter9: Deflections Of Beams

Section: Chapter Questions

Problem 9.5.15P: Use the method of superposition to find the angles of rotation 9Aand SBat the supports, and the...

See similar textbooks

Related questions

Q: 1. What is a four bar linkage? 2. Draw a four bar linkage and identify the crank, connecting rod,…

A: Given data:- crank = 2 in, connecting rod = 3 in, and rocker = 4 in To find:- What is a four bar…

Q: A mass weighing 11.5 kg falls a distance of 1.5 m upon the top of a helical compression spring.…

Q: The signboard truss is designed to support a horizontal wind load of 660 lb. If the resultant of…

Q: A railroad track is laid at a temperature of 15°F with gaps of 0.01 feet between the ends of the…

A: Given: Here are the given data, Gaps=0.01 ft Temperature, T1=15°FT2=110°F Length, L=33 ft To find:…

Q: A 180-lb man and a 120-lb woman stand side by side at the same end of a 300-lb boat, ready to dive,…

A: The mass of the man is mm=180 lb The mass of woman is mw=120 lb. The mass of boat is mb=300 lb. The…

Q: The wood beam in (Figure 1) is subjected to a load of P= 11 kN. Grains of wood in the beam at point…

A: The reaction at the support are calculated as: ΣFy=0Rleft+Rright=P=11…

Q: A pin-connected truss is loaded and supported as shown. Each aluminum member has a cross- sectional…

Q: 2..Assume that the cable GBH is replaced by a cable GB only (TBH-0). So the frame ACD is supported…

A: The free body diagram for the frame ACD is given below,

Q: 17-103 Air enters a rectangular duct at T₁ = 300 K, P₁ = 420 kPa, and Ma, = 2. Heat is transferred…

A: To find: The temperature and the Mach number at the duct exit. Given: The static temperature at the…

Q: The riding power mower has a mass of 130 kg with center of mass at G1. The operator has a mass of 95…

Q: For the frame and loading shown, determine the components of all forces acting on member ABE when P=…

A: This is truss member. For finding out all the horizontal & vertical reaction forces , we will…

Q: 7-42 C&S In cryogenic equipment, cold air flows in parallel over the surface of a 2-m x 2-m ASTM…

Q: A simple U tube manometer is used to measure the pressure of oil flowing in a pipeline. Its left…

A: Given data Specific gravity of oil = 1.79 Specific gravity of mercury=13.6 Find the density of oil…

Q: Using this equation FL/AE Q1/The rigid bar BDE is supported by two rods AB and CD. Rod AB is made of…

Q: 6.4 Two large diffuse parallel plates are maintained at temperatures T₁ = 1400 K and T₂ = 700 K. The…

Q: 3) Link AB of a robotic arm is rotating at a constant speed of 4 rad/s, while link BC is rotating at…

Q: 5. The hanger is supported using the rectangular pin. Determine the magnitude of the allowable…

A: Given: Allowable bearing stress = σb, allowable= 220Mpa, Allowable tensile stress = σt,allow=…

Q: Q3/A combustion chamber consists of tubular combustors of 15-cm diameter. Compressed air enters the…

A: Given, P1 = 480 kPa T1 = 550K V1=80 m/s Air-Fuel ratio = 40 Heat flow rate = 42,000 kJ/kg From…

Q: QAI=?" 5MPa,370°C e = 60% WHPT =? (ACTUAL)MW e=G58 2 REQUIRED! 2 MPa Q R = Q² + ₂0 = MCN CAT QR -…

A: "Inlet condition turbine 1"T[1] = 370[C]P[1] = 5000[kPa] P[2] = 2000[kPa] "Reheat pressure" T[3] =…

Q: What safety precautions should be taken during welding and cutting operations?

A: Welding and cutting operations can be extremely hazardous if proper safety precautions are not…

Q: If there are two cannons, both completely identical and were shot at same speed and angle. One is…

A: Solution: Given Data: h2,max=114h1θ1=θ2v1=v2 To Find: The time of flight of cannon 2 in terms of…

Q: Various hardness testing techniques qualify a material's ability to withstand shock loading. O True

A: This question is based on the concept hardness measurement.

Q: For an entropy value of O kJ/kg-K what would be the value of the corresponding enthalpy?

A: The entropy of a system is defined as the degree of disorder and uncertainty. Enthalpy of the system…

Q: Oil (SG = 0.92) fills both pipe "A" and pipe "B" which are vertically separated by 24-inches. The…

Q: Steam enters the turbine at 10 bar. Output pressure P = 1 bar, knowing turbine efficiency is 80%.…

A: GIvenP1=10 barP2=1barηT=80%part awhen T1=250oCPart b when T1=325oC

Q: The jet-powered aircraft has a mass of 25 tons and a center of mass at G. If a tow cable is attached…

Q: Wattmeter T₁ T₂ Q(W) 94.9 Note: Heat Transfer Results and Discussion T3 T4 99.3 92.6 83.0 75.0 66.3…

A: Given: d=30 mmt=30 min∆x=10 mm Solution: Q(W) T1 T2 T3 T4 T5 T6 T7 T8 T9 94.9 W 99.3 92.6…

Q: Water contained in a piston-cylinder assembly, initially at 300°F, a quality of 80 %, and a volume…

Q: 5. A plate is subjected to forces as shown below. It is supported by a ball-and-socket joint at A, a…

A: Find the reaction force at A, B and C

Q: Q3: A square element 8 8mm in an undeformed sheet of 0.8mm-thickness becomes a rectangle, 6.5 x…

Q: For the cantilever beam and loading shown, using method of integration (and singularity functions),…

A: First find the reaction at the supports :…

Q: 1. For the beam shown, find the reactions at the supports and plot the shear-force and bending…

A: Since you have posted multiple questions, we will provide the solution only to the first question as…

Q: 1. For the beam shown, find the reactions at the supports and plot the shear-force and bending…

A: Step:1

Q: A 50 lb force is applied to the wrench. Solve for the pin reaction at B as well as the gripping…

Q: Determine the force in member BD and the components of the reaction at C. Assume negative value as…

A: It is required to determine the force in member BD and reaction at C. consider the FBD of member…

Q: The overhanging beam is supported by a pin at A and the two-force strut BC Determine the horizontal…

Q: A system that has the ability to start, regulate, and stop a process to get the desired output is…

A: To choose: The correct option.

Q: P.5: For the unity feedback system shown K(s + a) (s+B)² G(s) is to be designed to meet the…

Q: Answer all the questions briefly 1. Define the term alloy and give an example. 2. Why is aluminum…

A: Alloy:- A alloy substance is made up of homogenous mixture of two or more metals or a metal and a…

Q: -. A body having a mass of 40 kg rests on a horizontal table and it is found that the least…

Q: Detc. mine the torque in newton-meter (Nm) and pound-foot (lb-ft) of a motor whose rated power and…

Q: 9. Calculate if a plate of SA-302-A with a thickness of 4.5 mm being made into a boiler drum meets…

A: The given information in the problem is shown in the following attached image:

Q: Consider a refrigeration system that operates on an actual vapor-compression refrigeration cycle…

A: Given:Refrigerant=R134aIsentropic efficiency of a compressor, ηisen=75.1%Refrigerant inlet condition…

Q: Two couples act on the frame. (Figure 1) Figure 100 lb -3 ft-d- 30° 30% 100 lb 150 lb -3 ft B 4 ft 1…

A: According to the given data F1=150lb F2=100lb d=7.8 ft We need to find Resultant moment of the force…

Q: How can I calculate the force tho

A: The stress is defined as the resisting force per unit area. here, σAl=12800 psiσsteel=18850…

Q: A 340 L tank contains steam, initially at 400°C, 3 bar. A valve is opened for 20 seconds and steam…

A: GivenV=340L=0.340 m3T1=400oCP1=3 bart=20sm˙o=-0.005 kg/s

Q: Question 7 5. Using WAB = 7.5 rad/s and GAB = 12.2 rad/s² for rod AB, determine the (a) angular…

Q: Question No.13: a.) Explain the working principle of fluid flywheel with neat sketch and mention the…

A: a) Fluid Flywheel: A fluid flywheel is an automatic transmission device that uses a fluid coupling…

Q: A cast-iron beam has the cross-sectional dimensions shown in the figure. If the allowable stresses…

A: Givenσyt=50MPaσyc=250MPaτy=55MPa

Q: L.Define the term alloy and give an example. 2.Why aluminium is useful for building aeroplane wings?…

A: These questions are based on the concept of material science. As per the guidelines we are…

Concept explainers

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.

Question

100%

For the beam loaded as shown, use the method of superposition to determine the deflection of the beam at end A. Assume the
following values:
El = 2.8 x 104 kN-m² (constant for entire beam)
L = 15 m
w = 56 kN/m
Answer:
VA=
i
B
W
mm
L
C

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Trending now

This is a popular solution!

Step by step

Solved in 6 steps with 9 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

-20 Derive the equations of the deflection curve for a cantilever beam AB carrying a uniform load of intensity q over part of the span (see figure). Also, determine the deflection Bat the end of the beam. Use the second-order differential equation of the deflection curve.
A cantilever beam has two triangular loads as shown in the figure. Find an expression for beam deflection Scusing Superposition. Find the required magnitude of load intensity q2in terms of q0so that the deflection at C is zero. Find an expression for the deflection at C if both load intensities, qxand q2, are equal to q0.
A beam ABC is fixed at end A and supported by beam DE at point B (sec figure). Both beams have the same cross section and are made of the same material. Determine all reactions due to the load P. What is the numerically largest bending moment in cither beam?
-3 The deflection curve for a simple beam AB (see figure) is given by v=q0x360LEI(7L410L2x2+3x4) Describe the load acting on the beam.
-22 Derive the equations of the deflection curve for a simple beam AB with a distributed load of peak intensity q0acting over the left-hand half of the span (see figure). Also, determine the deflection cat the midpoint of the beam. Use the second-order differential equation of the deflection curve.
-10 The simple beam AB shown in the figure supports two equal concentrated loads P: one acting downward and the other upward. Determine the angle of rotation A at the left-hand end, the deflection 1under the downward load, and the deflection 2 at the midpoint of the beam.
Copper beam AB has circular cross section with a radius of 0.25 in. and length L = 3 ft. The beam is subjected to a uniformly distributed load w = 3.5 lb/ft. Calculate the required load P at joint B so that the total deflection at joint B is zero. Assume that£ = 16,000 ksi.
A simple beam ACE is constructed with square cross sections and a double taper (see figure). The depth of the beam at the supports is dAand at the midpoint is dc= 2d 4. Each half of the beam has length L. Thus, the depth and moment of inertia / at distance x from the left-hand end are, respectively, in which IAis the moment of inertia at end A of the beam. (These equations are valid for .x between 0 and L, that is, for the left-hand half of the beam.) Obtain equations for the slope and deflection of the left-hand half of the beam due to the uniform load. From the equations in part (a), obtain formulas for the angle of rotation 94at support A and the deflection Scat the midpoint.
A fixed-end beam AB carries point load P acting at point C. The beam has a rectangular cross section (b = 75 mm, h = 150 mm). Calculate the reactions of the beam and the displacement at point C. Assume that E = 190 GPa.
The cantilever beam ACE shown in the figure has FlexuraI rigidity EI = 2,1 x 106kip-in". Calculate the downward deflections Scand 8Sat points C and B, respectively, due to the simultaneous action of the moment of 35 kip-in. applied at point C and the concentrated load of 2,5 kips applied at the free end B.
Beam ABC is loaded by a uniform load q and point load P at joint C. Using the method of superposition, calculate the deflection at joint C. Assume that L = 4 m, a =2ra, q = 15 kN/m, P = 7.5 kN, £ = 200 GPa, and / = 70.8 X 106 mm4.
-12 Derive the equation of the deflection curve for a cantilever beam AB supporting a load P at the free end (see figure). Also, determine the deflection Band angle of rotation bat the free end. Use the second-order differential equation of the deflection curve.