For the beam and loading shown in Fig.3: 1- Draw the shear force and bending moment diagrams. 2- Find the location and magnitude of the maximum bending moment. 3- Determine the maximum normal stress due to bending. 10cm 6 cm 3 cm Cross-sectional area A 10 KN 20 KN B 0.5m 0.5m 0.5m D Fig 3 Beam Loading and Cross Section 2-(X-1.5) 5 kN/m 1m 14 E

For the beam and loading shown in Fig.3: 1- Draw the shear force and bending moment diagrams. 2- Find the location and magnitude of the maximum bending moment. 3- Determine the maximum normal stress due to bending. 10cm 6 cm 3 cm Cross-sectional area A 10 KN 20 KN B 0.5m 0.5m 0.5m D Fig 3 Beam Loading and Cross Section 2-(X-1.5) 5 kN/m 1m 14 E

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

B6
Determine (a) the maximum bending stress, (b) the maximum shearing stress due to V in the simply supported beam shown in the figure and (c) the shearing stress at a point 1m from the right support and 2 cm below the top. 5 cm 40 kN/m 16 kN m A 1-+-2 2 m m CF -2 m 16 cm
Given the beam shown in Fig. E2, answer the questions below. | 275 kN | 275 kN A 1.5m 1.8m 1.8m Fig. E2 (i) Knowing that o all = 160 MPa and Tall = 100 MPa select the most economical metric wide-flange shape that should be used to support the loading shown. (ii) Determine the value expected for the normal stress at the junction of the flange and the web of the selected beam. (iii) Determine the value expected for the shear stress at the junction of a flange and the web of the selected beam. (iv) Draw the stress element, and indicate the normal and shear stresses, for a point located at the junction of a flange and the web of the selected beam. (v) Draw the Mohr's Circle for the stress element determined in (iv). (vi) For the stress element in (iv), calculate the major principal stress o1 and the minor principal stress o3
A thin beam with a solid rectangular cross-section is loaded as shown in Figure Q7 below. W W L/3 L/3 L/3 Figure Q7 What is the ratio of the maximum to nominal shear stress for the beam described in Question 7? O a. 3:2 O b. 1:4 Ос. 3:1 O d.2:1 O e. 1:2 O f. None of the provided answers are correct. O 8. 1:1
A beam with the T section shown in Figure 3.24a issubjected to a shear force of 8 kips. Find the maximum shear stressand the value of shear stress at the location of the juncture of the weband the flange of the T.
19e m Find the total deformation of 14022 the bar with circular cross- Section of 3cm diameter. E = 1440 x10³² MPa. it your bones van L x 2m x f=4x kr/m 3m
Determine the reactions and draw the shear and bending moment diagrams for the beam shown in Figure Q3 using the method of consistent deformations. 250 kN 250 kN 30 kN/m 30 kN/m C E F10 +sm-5 m-5 m-5 m--10 m m- El = constant Figure Q3: Four-span continuous beam.
The beam shown in Fig1.carries a concentrated load of W and a total distributed load of 8 W. Determine the maximum safe value W that will not exceed allowable stresses in tension of 60 MPa, in compression of 90 MPa, or in shear of 15 MPa. 1m W ᎦᎳ ? 15 2m 1m 20mm Fig.1 140mm 20mm 2 20mm 140mm
None
Please solve the reactions and draw the shear and bending moment diagrams for the beam shown using the Consistent Deformation method.
iss 40 mm 200 m 40 mm FIG. P5.100 5.100 The bending moment acting on the cross section of the beam is M = 1.8 kN m. Find the maximum tensile and compressive bending stresses acting on the cross section.
lute flexural stress. For the beam shown in Figure (3), given INA = 1.+ 10 mm", calculate the transverse shearing stress at points A, C and G on the section at the left support of the beam.