For an electric network shown in the following figure 1H IF IF 10 Figure 1: 1). find the transfer function from V;(s) to Vo(8); 2). selecting state variables, find the state space model for this network with v:(t) as the input signal and vo(t) as the output signal; 3) show that the transfer function obtained in 1) can be also derived from the state-space model in 2), assuming zero initial values of state variables.

For an electric network shown in the following figure 1H IF IF 10 Figure 1: 1). find the transfer function from V;(s) to Vo(8); 2). selecting state variables, find the state space model for this network with v:(t) as the input signal and vo(t) as the output signal; 3) show that the transfer function obtained in 1) can be also derived from the state-space model in 2), assuming zero initial values of state variables.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Derive the transfer function for the networks (a) and (b)
TFS Set up the ETS coefficients for the following signal - no need to complete the integration, as I am just checking for proper set up, including limits, notation, etc. Write in general terms of fundamental frequency, i.e., @o, however, at some point, you must clearly define the value of a base on the graph below. a) b) What is ao? 6 4 2 -6-4-2 What are an and bn for n >0? x(t) 246
Question 7) Design a JFET amplifier network with ldss-8 mA, Ve=-4 V, R1=110 MN, R2=10 MQ. When an input AC signal V=10 mV is applied to the network, an output signal Vo=2V AC is obtained. (suppose that ra2 10R0) a) Draw the JFET amplifier network you prefer to design, and explain why you choose this network b) Explain the aims and reasons in using of all the peripheral components handled on your network c) Draw AC equivalent re model of the network (5p.) d) Draw transfer characteristic curve and derive lda and Vasa values from the characteristic curve e) Calculate Av, gm, VoD, Ro, Rs, Z; and Zn. Note: Please, do not forget using resistors and capacitors as peripheral elements whatever required for your complete design in the question (i.e. input, output terminals etc.)
Subject : Electronics Engineering A CE amplifier has mid frequency gain of 200. The upper and lower 3dB frequency of the amplifier is 10KHz and 100KHz respectively. A negative feedback of 10% is incorporated in the amplifier circuit. Find the new gain and new bandwidth after feedback?
The figure below shows the one-line diagram of a four- bus power system. The voltages, the scheduled real power and reactive powers, and the reactances of transmission lines are marked at this one line diagram (The voltages and reactances are in PU referred to 100 MW base. The active power P2 in MW is the last three digits (from right) of your registration number (i.e for the student that has a registration number 202112396, P2 =396). [10] Starting from an estimated voltage at bus 2, bus 3, and bus 4 equals V2 (0) = 1.15<0°, V3 = 1.15 < 0°, V4 1.1< 0°. 1- Specify the type of each bus and known & unknown quantities at each bus. 2- Find the elements of the second row of the admittance matrix (i.e. [Y21 Y22 Y23 Y24]). 3- Using Gauss-Siedal fınd the voltage at bus 2 after the first iteration. 4- Using Newton-Raphson, calculate: |- The value of real power (P2), at bus 2 after the first iteration. Il- The second element in the first row of the Jacobian matrix after the first iteration. 2 P2…
I need the answer as soon as possible
Find transfer function of given signal flow graph using block diagram reduction techniques.
A boost converter is a dc-to-dc switched power supply in which the voltage output is larger than the voltage input. A block diagram for a peak current mode controlled converter is shown below. Find the transfer function Vo(s)/V/(s). Tja(s) Tpa(s) Kf Fm R₁ Tp.(s) K₁ H.(s) Tma(s)
Find values of Cc1, Cc2 and Cs based on the transfer function
i need the answer quickly
Problem 3. Find the transfer function, V₁(s)/V(s), for the electrical network shown in Figure 3, which contains a nonlinear resistor whose voltage-current relationship is defined by i = 2e0.1v,, where i, and v, are the resistor current and voltage, respectively. Also, v(t) in Figure 3 is a small-signal source. v(1) in Wilh Figure 3 IH VISO Nonlinear resistor 20 V
Calculate the current of in the circuit shown below when the BJT has VBE | ON = 0.7 , B=150 ( use VCC=30V, RC=2k, and RB=15k) Vc Rc RB VBE The ersity