For a surface, how is irradiation defined? For diffusely incident radiation, how isirradi ation on a surface related to the intensity of incident radiation?

Answered: Image /qna-images/answer/f39d083e-b0a0-4703-8807-f92793a1b0ee.jpg

Answered: For a surface, how is irradiation…

For a surface, how is irradiation defined? For diffusely incident radiation, how is irradiation on a gurface related to the intensity of incident radiation?

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter11: Heat Transfer By Radiation

Section: Chapter Questions

Problem 11.2P: A tungsten filament is heated to 2700 K. At what wavelength is the maximum amount of radiation...

See similar textbooks

Related questions

Q: The peak wavelength of radiation emitted by a black body at a temperature of 2000 K is 1.45 pm. If…

A: Given, Temperature T1 = 2000 K Peak wavelength of radiation emitted by body at T1 = λ1 = 1.45 μm…

Q: A circular cone of diameter D with a length L ispositioned on a common axis with a circular disk,…

A: The diagrams of the cone and cylinder are given as, For both given configurations, Now, apply the…

Q: Two parallel disks of diameter D = 0.8 m separated by L = 0.4 m are located directly on top of each…

Q: 0.3 0.1 3. 7.

A: Any given surface at any given temperature (absolute) will emit thermal radiation in all possible…

Q: Consider two very large parallel plates with diffuse, gray surfaces.The top surface is at T = 1000K…

Q: Consider a 20-cm x 20-cm x 20-cm cubical body at 750 K suspended in the air. Assuming the body…

Q: (a) Determine the radiant power from the heater, which is incident on the disk, q,1- What is the…

Q: Consider two coaxial parallel circular disks of equal diameter D that are spaced apart by a distance…

A: Considering the diameter of the two discs are equal. Thus, the radii of the two-discs are equal.…

Q: 13.18 A drying oven consists of a long semicircular duct of diameter D = 1 m. T; = 1200 K - T2 = 325…

Q: The spectral absorptivity of a diffuse surface is provided in the figure. If the surface is at 300 K…

A: To find : The total emissivity . Given : The temperature of surface is T=300 K Concept used : The…

Q: hin, disk-shaped silicon wafer of diameter D=20 cm on a production line must be maintained at a…

A: A thin, disk-shaped silicon wafer of diameter D=20 cm on a production line must be maintained at a…

Q: Determine the view factors from the base of the pyramid shown in Figure 12-14 to each of its four…

Q: QUESTION 6: Two parallel disks of diameter D = 0.8 m separated by L = 0.4 m are located directly on…

A: Given Data,D=0.8mL=0.4mT1=T2=450K (black body)T3=300K (black body) i.e us the backside…

Q: the outer surface temperature of the furnace should be kept below 45°C. Based on the above…

Q: Calculate the radiation heat exchange in 1 day between two black planes having the area of the…

A: Write the expression for the radiation heat transfer through the surface. Now substitute the…

Q: A small disc-shaped earth satellite, 1m in diameter, circles the earth (radius 6250 km) at a…

A: Given details: d=1 mε1=ε2=0.3Tsatellite=-18°CT2=27 °Cσ=5.67×10-8 w/m2k4 here σ=stefan boltzman…

Q: The peak wavelength of radiation emitted by a black body at a temperature of 2000 K is 1.45 um. If…

A: GIVEN DATA - λ1=1.45μm T1=2000K WE HAVE TO CALCULATE TEMPRATURE CORRESPONDING TO 2.90 WAVELENGTH

Q: Consider a cylindrical enclosure with A1, A2, and A3 representing the internal base, top, and side…

A: Given: The diagram of the cylindrical enclosure with having area of surfaces 1, 2, and 3 is given…

Q: Determine the net heat transfer by radiation between two gray surfaces, A (εA = 0.90) and B (εB =…

Q: How does radiosity for a surface differ from the emitted energy? For what kind of surfaces are these…

A: Radiosity is the ration of total radiation energy leaving the surface per unit area. Radiosity is…

Q: Consider a cylindrical furnace with ro = H = 1 m, as shown in the figure. The top (surface 1) and…

Q: A furnace is of cylindrical shape with R = H = 2 m. The base, top, and side surfaces of the furnace…

A: Given: The height of the cylindrical shape, H = 2 m The radius of the cylindrical surface, R = 2 m…

Q: The human skin is “selective” when it comes to theabsorption of the solar radiation that strikes it…

A: It is required to determine the absorptivity of the skin for different wavelengths. For a1 For a2…

Q: The filament of a 75-W light bulb may be considered a blackbody radiating into a black enclosure at…

A: Given Data Energy radiated per second is: q=75 W Length of the filament is: l=5 cm=0.05 m The…

Q: How can you determine the view factor F12 whenthe view factor F21 and the surface areas are…

A: Reciprocity theorem: The reciprocity theorem is used to determine the view factor F12 when areas of…

Q: 8. A black body has an effective surface temperature of rmine: (a) The total radiation energy (W/m²)…

Q: A furnace that has a glass window of 50 cm X 50 cm can be considered as a blackbody at 1200 K. If…

Q: 13-44 A furnace is of cylindrical shape with R = H = 3 m. The base, top, and side surfaces of the…

A: Given data:Radius of cylinder, R = 3 mHeight of cylinder, H = 3 mTemperature of top surface, T1 =…

Q: Calculate the net heat flux per unit area and by radiation between two infinitely large parallel…

A: Introduction: Radiation heat transmission occurs in the form of electromagnetic waves, primarily in…

Q: (a) Two surfaces, A and B has a temperature of 4500 K and different spectral emissivity as shown in…

A: Given: The temperature, T = 4500 K The Stefan Stefan Boltzmann’s constant, σ = 5.67x10^-8 W/m^2.K

Q: Consider the sun, which is considered to be a blackbody with a surface temperature of roughly 5800…

A: Given : The surface temperature of sun= 5800 K Assumption : Sun is a black body.

Q: A gray body with a constant surface temperature of 7000C and a surface area of 500cm2 radiates in a…

Q: determine the view factor, and the net heat transfer by radiation between two gray surfaces, A (εA=…

A: Answer: (d) Qnet = 5817.6 Watt ..... (for concentric cylindrical tube). (e) Qnet = 32616 Watt…

Q: Consider a 20-cm-diameter spherical ball at 800 K suspended in air as shown in Fig. 12-12. Assuming…

Q: A black body has a temperature of 3000 Kelvin. What is the wavelength of peak radiation emanating…

Q: A blackbody of surface area 10 cm' is heated to 127°C and is suspended in a room at temperature…

Q: Consider the surfaces shown below that are black. It is symmetric across the dashed line. Determine…

A: radius of semicircle =0.5m length from A1 to A2=1.5m area of semicircle =πr22…

Q: Consider two coaxial parallel circular disks of equal diameter D = 1 m spaced apart by 1 m, and two…

A: The view factor in the heat transfer theory defines the degree of radiation energy transfer between…

Q: A certain surface maintained at 1400 K has the following spectral emissive characteristics: =0.08…

A: From the weins displacement law,

Question

For a surface, how is irradiation defined? For diffusely incident radiation, how is
irradi ation on a surface related to the intensity of incident radiation?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A tungsten filament is heated to 2700 K. At what wavelength is the maximum amount of radiation emitted? What fraction of the total energy is in the visible range (0.4to0.75m)? Assume that the filament radiates as a graybody.
1.54 The soldering iron tip in Problem 1.53 becomes oxidized with age and its gray-body emittance increases to 0.8. Assuming that the surroundings are at 20°C, determine the power requirement for the soldering iron.
Based upon the reradiating properties of absorptivity, reflectivity and transmissivity, how would you distinguish between the following: Black body, white body, transparent body and opaque body.
! Required information Irradiation on a semi-transparent medium is at a rate of 640 W/m². If 160 W/m² of the irradiation is reflected from the medium and 130 W/m² is transmitted through the medium, Determine the absorptivity of the medium. The absorptivity of the medium is 0.75 X
Derive the expression for radiation heat exchange between two gray surfaces connected by single refractory surface.
1) a) Explain how characteristic and continuous x-ray radiations are generated. b) On an x-ray intensity vs. wavelength graph, schematically show Kα, Kβ and continuous radiations. Explain why the intensities and wavelengths of Kα and Kβ are different.
A solar dish has a reflector with a diameter of 100 cm and a receiver having a diamter of 10 cm. If the solar irradiance is 1000 w/m2, what is the concentration ra O a. 1 O b. 10 O c. 1000 O d. 100
Irradiation on a semi-transparent medium is at a rate of 640 W/m². If 160 W/m² of the irradiation is reflected from the medium and 130 W/m² is transmitted through the medium, 1) Determine the absorptivity of the medium. 2) Determine the reflectivity of the medium. 3) Determine the transmissivity of the medium.
Calculate the radiation in watts per square centimeter from a block of copper at 200°C and at 1000°C. The oxidized copper surface radiates at 0.60 the rate of a black body.
QUESTION 10 a) A furnace that has a glass window of 50 cm X 50 cm can be considered as a blackbody at 1200 K. If the transmissivity of the glass is 0.7 for radiation at wavelength less than 3 µm and zero for radiation at wavelength greater than 3 µum, determine the fraction and the rate of radiation coming from the furnace and transmitted through the window. b) The reflectivity of aluminum coated with lead sulfate is 0.35 for radiation at wavelength less than 3 um and 0.95 for radiation at wavelength greater than 3 µm, i. determine the average reflectivity of this surface for solar radiation (T=5800 K) and the radiation coming from the surface at room temperature (T=300 K) ii. Kindly evaluate based on the emissivity and the absorptivity of this surface at both temperature, if the material is suitable for use in solar collectors.
Derive expression for monochromatic emissive power for small and long wavelength.
7. The emissive power of a blackbody, at 0.8 µm wavelength is measured as 1E5 W/m², µm. Find the blackbody temperature. [Ans. 1739 K]