For a single phase full wave AC controller, the input rms voltage is V_{s} = 120V 60 Hz load is L = 6.5mH and R = 2.5 2. The delay angles of thyristors are equale a_{1} = a_{2} = pi / 2 Determine (a) the conduction angle & of the thyristor, which conduct positive half cycle (b) the rms output voltage V_{0} (c) the rms thyristor current I_{R} (d) the output current.

For a single phase full wave AC controller, the input rms voltage is V_{s} = 120V 60 Hz load is L = 6.5mH and R = 2.5 2. The delay angles of thyristors are equale a_{1} = a_{2} = pi / 2 Determine (a) the conduction angle & of the thyristor, which conduct positive half cycle (b) the rms output voltage V_{0} (c) the rms thyristor current I_{R} (d) the output current.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter12: Power System Controls

Section: Chapter Questions

Problem 12.4P

See similar textbooks

Similar questions

The single - phase ac voltage controller with inductive load. Plot the waveform of output voltage and voltage in each thyristor if the B = 10 %3D degree and delay angle (alpha) in both thyristor is 1- (30 degrees) 2- (90 degrees) 3- (120 degrees)
[4] The half wave ac controller has rms output voltage equal to input rms Vs at.......... (5] In single phase bidirectional ac controller, the RMS output voltage can be varied between zero to.............. of input voltage
A single phase full wave AC voltage controller has a resistive load of 5 ohms and an input voltage of Vs = 240 V (RMS), 50 Hz. The delay angles of both thyristors are set to 90 degrees. If the RMS output voltage Vo is equal to 169.7V, then the input power factor is equal to: Select one: a. 0.85 lagging b. 0.768 lagging c. 0.707 lagging d. None of these
5. The single phase full wave AC voltage controller operates on a single phase supply voltage of maximum voltage as 230 V, at 50 Hz. If the triac is triggered at a delay angle of 45°, during each half cycle of input supply. Find the rms output voltage, input power factor and the power in the load. 6. A voltage source v= 100 sin 377t supplies a resistive load of 100 2 through a pair of back to back connected thyristor (ac regulator). Calculate the power in the load, if the thyristor firing angle is 2n/3 with respect to the supply voltage.
Draw the full-wave voltage doubler circuit diagram. When a 1:4 transformer is used in this circuit andIf Vo=12sin(314t) alternative signal is obtained at the output, the frequency of the input signal, maximum and rmsCalculate its value.
A single phase full wave AC voltage controller has a resistive load of 5 ohms and an input voltage of Vs = 220 V (RMS), 50 Hz. The delay angles of both thyristors are set to 90 degrees. The maximum power that can be delivered to the load is: Select one: a. 5.65 kW b. 9.68 kW c. 11.52 kW d. None of these
Q1) A single-phase AC voltage controller is connected to an inductive load with a resistance of 10 and load impedance angle of 45°. The input ac voltage is 230 V at 50 Hz. (a) Draw the load voltage waveforms and derive an expression for the rms load voltage. (b) Determine the maximum load voltage, maximum load current, and range of delay angie for which the load voltage does not change.
4.) A transformer has a primary coil with 300 windings, and secondary coil has 400 windings. The input AC power supply is 120 volts (Vrms). A) Is this a step-up or step-down transformer? B) What is the rms voltage across the output terminals (Vrms)? C) What is the peak voltage across the output terminals (Vmax)? Primary Secondary imm ac input
Single phase half wave AC-AC converter has a resistance of R = 50 ohms. Input voltage is given as 230 Vrms. Transformer conversion ratio is 1:1. If T1 thyristor is triggered at 60 degrees; a)Rms output voltage? b)Output power? c)RMS load current and average load current? d)Input power factor? e)Average and RMS thyristor current?
1- Derive expression for the output rms voltage for single phase ac voltage controller with resistive load
a) Demonstrate input and output waveform of single phase Cyclo-converter such that output frequency is 1/3 of input supply frequency with circuit diagram. b) Perform the calculation to analyze (i) output RMS voltage and (ii) input power factor of single-phase AC voltage controller as shown in the following figure. Suppose converter has a resistive load of R=‘A’ Ohm and the input voltage is Vs=220, 50Hz with a delay angle of π/3. A= 4
An ac controller has a resistive load of R = 10 2 and the input is 220 V, 50 Hz. The thyristors switch is on for n 25 cycles and for m 75 cycles. Determine: (i) (ii) (iii) the rms value of the output voltage, the input power factor, the average and rms current through thyristors.