For a motorbike absorber system, a helical compression spring with squared and grounds ends is to be designed with given force and deflection requirement as shown in Figure 4. Given the condition that the preload of motorbike weight, 500 N is loaded on the compression spring and additional load produce deflection of 60 mm. Presetting is to be used. The loading is static. Given that the spring material shear modulus is 79 GPa and shear force correction factor is 1.0644. The clash allowance is 10% of the maximum deflection The tensile 500 N of strength of the spring is 1650 MPa. Determine 500 N 1000 N F, 60 mm Clash allowance Music wire with d = 5 mm Figure 4 (a) the stiffness of the spring. (b) the shear stress (c) the diameter D (d) the number of turns N. (e) the free length L, after unloading

For a motorbike absorber system, a helical compression spring with squared and grounds ends is to be designed with given force and deflection requirement as shown in Figure 4. Given the condition that the preload of motorbike weight, 500 N is loaded on the compression spring and additional load produce deflection of 60 mm. Presetting is to be used. The loading is static. Given that the spring material shear modulus is 79 GPa and shear force correction factor is 1.0644. The clash allowance is 10% of the maximum deflection The tensile 500 N of strength of the spring is 1650 MPa. Determine 500 N 1000 N F, 60 mm Clash allowance Music wire with d = 5 mm Figure 4 (a) the stiffness of the spring. (b) the shear stress (c) the diameter D (d) the number of turns N. (e) the free length L, after unloading

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

(Q6) A solid spring steel shaft in small engine with 5hp at 3000rpm is used as a torque measuring device at the rated load. Select a suitable length and diameter combination for this measurement assuming an angular deflection of 10.. The modulus of elastic of the spring steel 28.6x106 psi and the Poisson's ratio is 0.3.
Part A For a hard aluminum notched part having notch dimension r = 0.75 in, geometric stress-concentration factor Kt = 2.8, material strength Sut = 50 kpsi, and bending loading type, find the Neuber factor, a (in inches). Part B Find the material's notch sensitivity, q. Part C Find the fatigue stress-concentration factor. Kf.
A shaft subjected to bending moment varying from -200 N m to +500 N m and a varying torque from 50 N m to 175 N m. If material of the shaft is 30C8, stress concentration factor is 1.85, notch sensitivity is 0.95 reliability 99.9% and factor of safety is 1.5, find the diameter of the shaft. The load on a bolt consists of an axial pull of 10 kN together with a transverse shear force of 5 kN. Find the diameter of bolt required according to a.Maximum strain energy theory; and b.Maximum distortion energy theory. Take permissible tensile stress at elastic limit = 100 MPa and poisson’s ratio = 0.3
Define the rigid body used in statics. According to this; rigidity of bolt-nut connected elementBased on the value, the bolt diameter is 20 mm and the safe value of the bolt material.Calculate the stiffness values of the bolt and the intermediate element plate. (Note: Bolt's9x10 ^ 2 times as stress value ??? / cm ^ 2take as.). Strain gaugeElongation in bolt length measured with 250 ??, shortening amount in intermediate element platesIt was measured at 125 ??.
A shaft subjected to bending moment varying from -200 N m to +500 N m and a varying torque from 50 N m to 175 N m. If material of the shaft is 30C8, stress concentration factor is 1.85, notch sensitivity is 0.95 reliability 99.9% and factor of safety is 1.5, find the diameter of the shaft. The load on a bolt consists of an axial pull of 10 kN together with a transverse shear force of 5 kN. Find the diameter of bolt required according to Maximum principal stress theory; Maximum shear stress theory; Maximum principal strain theory; Maximum strain energy theory; and Maximum distortion energy theory. Take permissible tensile stress at elastic limit = 100 MPa and poisson’s ratio = 0.3
A mechanism used in a punchingmachinery consists of a tension spring assembled with a preload of 30 N. The wire diameter of spring is 2 mm with a spring index of 7. The spring has 10active coils. The spring wire is hard drawn and oil tempered having the following material properties:Design shear stress = 780 MPa Modulus of rigidity = 80 kN/mm2Identify (a) the initial torsional shear stress in the wire, (b) the spring rate, and (c) the force to cause the body of the spring to reach its yield strength.
2. A helical valve spring is to be designed for an operating load range of approximately 90 to 135 N. The deflection of the spring for the load range is 7.5 mm. Assume a spring index of 10. Permissible shear stress for the material of the spring 480 MPa and its modulus of rigidity 80 kN/mm. Design the spring. %23 4C - 1 0.615 Take Wahl's factor C being the spring index. 4C - 4 |Ans. d-2.74 mm; D 27.4 mm; n 6|
The material is a spring wire has a shear modulus of 1.2 x 107 lbf/in2. The maximum allowable stress under design conditions is 50,000 lbf/in2. The spring index is 7. Assume the maximum stress is experienced when a 700 lbm objects falls from a height of 46 in above the tip of the spring, impacts squarely on the spring, and deflects the spring 10 in. Determie: 1. The minimum wire diameter is most nearly A. 0.58 in B. 0.88 in C. 1.4 in D. 1.8 in 2. The mean coil diameter is most nearly A. 8.6 in B. 10 in C. 13 in D. 16 in 3. The number of active coils is most nearly A. 8 B. 11 C. 12 D. 14
Problem 1: The pin in a Box-Pin coupling is acted upon by a force (F), that varies as random variable due to misalignment as (2, 0.08) kN. The load act at a distance (1) that varies as (25 ± 3) mm. The diameter of the pin (D) is 18 mm. The fillet radius at the pin shoulder is about 1.5 mm. The stress concentration factor due to fatique in bending is thus a random variable kb that could vary from 1.3 to 1.5. The pin is made of steel AISI 4340 with mean endurance strength in bending of 400 MPa, and a standard deviation of 25 MPa. Determine the pin diameter (d), if one pin in every 10000 may be permitted to fail. R1.6 O L Problem (1)
The material is a spring wire has a shear modulus of 1.2 x 107 lbf/in2. The maximum allowable stress under design conditions is 50,000 lbf/in2. The spring index is 7. Assume the maximum stress is experienced when a 700 lbm object falls from a height of 46 in above the tip of the spring, impacts squarely on the spring, and deflects the spring 10 in. Determie:1. The minimum wire diameter is most nearlyA. 0.58 in B. 0.88 in C. 1.4 in D. 1.8 in2. The mean coil diameter is most nearlyA. 8.6 in B. 10 in C. 13 in D. 16 in3. The number of active coils is most nearlyA. 8 B. 11 C. 12 D. 14
2. A l-in diameter rotating solid round bar has a groove 0.1-in deep with a 0.1-radius machined into it. The bar is made of AISI 1020 CD steel and is subjected to a bending moment 1000 lbf-in. For the S-N curve of the material, let f= 0.9. Let notch sensitivity q x 0.8. Estimate the number of cycles to failure.
A hard-drawn steel wire extension spring has a wire diameter of 4mm, an outside coil diameter of 28 mm, and initial tension of 1200 N is applied to the spring. The spring shows an extension of 85 mm. The approximate number of turns is 25. From the given information: Determine the physical parameters of the spring such as mean diameter, spring index, maximum shear stress, total number of turns, Wahl’s stress factor, free length of the spring, and pitch of the coil