For a group of piles 3x5 with pile diameter is 0.4m and centre to centre spacing is 2.8 m,if the settlement of the single pile is 12 mm ,the settlement of the group is; 3 - 41.9 mmn 17.1 mm 12.1 mm 146.4 mm Boş bırak

For a group of piles 3x5 with pile diameter is 0.4m and centre to centre spacing is 2.8 m,if the settlement of the single pile is 12 mm ,the settlement of the group is; 3 - 41.9 mmn 17.1 mm 12.1 mm 146.4 mm Boş bırak

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: The unit adhesion developed between clay and pile shaft of a friction pile embedded 10m into a…

A: The unit adhesion developed between clay and pile shaft of a friction pile, Cu=4 tm2 Adhesion…

Q: Estimate the pile length required to carry the 900 kN axial load for the pile-soil system shown the…

A: Given the details of Soil profile as:Soil 1:C= 35 kPaSoil 2:C= 45 kPaSoil 3:C= 55 kPaSoil 4:C= 60…

Q: 1. An HP 250x84.98 steel pile is driven into sand as shown. Determine the frictional resistance if…

Q: A group of 9 piles of 33 cm diameter is arranged in a square configuration with a center-to-center…

A: Please refer the attached image for complete solution. THANKYOU !

Q: a Pile have diameter of 0.4 m and ultimate pile capacity 12000 Kn, F.s=3 if the load will applies =…

Q: A 0.45m square pile is to be driven at a depth of 10m into the soil. What is the allowable pile…

A: B (size of pile) = 0.45m d (depth of pile) = 10m FOS = 3

Q: 3- The pile is classified as Micro (Mini) pile when its diameter is: *less than 0.2m less than 0.3m…

Q: Q4.11 Calculate the combined settlement (&1 + ô2 + ô3) of a single bored pile in a deep uniform clay…

A: Given - Pile depth = 7 m Pile diameter = 0.5 m Pile Load = 120 kN μ = 0.5 Esoil = 3.8 MPa, Epile =…

Q: A pile with a square cross-section, B × B = 0.5 m × 0.5 m, is driven in a clay soil which has an…

Q: A concrete pile is 15 m long and has 406 mm diameter circular cross section. The pile is fully…

Q: An 18-in.-diameter, closed-ended steel pipe pile is driven 45 ft through soft sandy silt to bear on…

A: The tip resistance is generally obtained by the force required to push the tip of the cone…

Q: A 5x 5 group piles of 0.4 m diameter displacement piles are to be constructed. The spacing between…

A: Solution: Given Data: d=0.4mthickness of pile, z=1.2 mLength of pile, L=20 mSpacing of pile=3…

Q: 3. As shown in the diagram, the RC solid precast square pile will be lifted up by two points, the…

Q: A group of 16 piles is arranged in a square pattern. The pile diameter is 350 mm. The length of pile…

A: The diameter of each pile, Total number of pile, The center-to center distance of pile is 1 mThe…

Q: What is the pile bearing capacity if the Downward drag = 0.6 psi, h1 = 30', h2 = 4', Frictional…

A: Downward drag = 0.6 psi, Height , h1 = 30',Height , h2 = 4',Frictional stress = 3.5psiAxial stress =…

Q: A square pile group of 9 piles passes through a recently filled up material of 3.5 m depth. The…

A: A square pile group of 9 piles,Depth of pile = 9 m,Depth of soil fill =3.5 m,Diameter of the pile=30…

Q: Square concrete piles are arranged in 5 row by 5 column formation beneath the pile cap. These piles…

A: The efficiency of the pile group is defined as the ratio of the average capacity of a pile in the…

Q: layer. Clay soil: c=40 kPa, Nc=7.5 Piles: Diameter = 350mm, Length=35m, Pile to pile spacing (center…

A: The question is based on the group of piles installed in the clay. The thickness of the pile cap,…

Q: A group of piles as shown on the figure has a cross section of 0.30 m x 0.30 m. It has a total…

Q: A group of nine piles is arranged in a square pattern and is used as a foundation for column in…

A: Given-9-pile group arranged in a square pattern,foundation in sand,diameter d= 350 mm= 0.35…

Q: 05. Estimate the pile length required to sustain an uplift force for the pile (30 x 30 cm) shown in…

Q: A group of nine piles is arranged in a square pattern and is used as a foundation for column in…

A: Given-9-pile group arranged in a square pattern,Foundation in sand,Diameter d=350 mm=0.350m,Spacing…

Q: exampley Determine the ultimate load of closed ended pipe pile using the Static load test data of…

Q: 2. Three cast-in-place square piles with a side length of 700mm are installed under a certain…

A: Determine the properties of each soil layer. The properties of each soil layer are given in the…

Q: A 16 in diameter, 45 ft long drilled displacement pile is to be constructed in a silty sand with 30…

A: Given- d=16 inl=45ftd=20ftFOS=2.8

Q: What is the diameter to thickness ratio of the conical pile sample after carefully flattening or…

A: Answer:- D = 4t to 8t Explaination Carefully flatten the conical pile to a uniform thickness and…

Q: A group of 9 piles of 27 cm diameter is arranged in a square configuration with a center-to-center…

A: Given data in question Cohesion Adhesion factor Square pile Spacing Length To find out Ultimate…

Q: Calculate the combined settlement (81 + 82 + 83) of a single bored pile in a deep uniform clay layer…

Q: A group of 9 piles of 31 cm diameter is arranged in a square configuration with a center-to-center…

Q: A- The load (Q=900 ton) locate at x, determine the max. & min. pile reaction for the given condition…

A: The pile is the supporting or substructure for the bridge or building when loading is acting due to…

Q: a group of 9 piles of 29 cm diameter is arranged in a square configuration with a center-to-center…

A: Total number of piles = 9Diameter of pile =29cm =0.29mCentre to centre spacing of piles, S…

Q: The horizontal floor with a length of 15 m, has one downstream sheet pile with a depth is 12 m, an…

A: H=3 m Take ρ of concrete=2.45α=bd=1512=1.25λ=1+1+α22=1+1+1.2522=1.3 Required: To calculate floor…

Q: A square pile group of 9 piles passes through a recently filled up material of 3.5 m depth. The…

A: A square pile group of 9 piles,Depth of pile = 9 m,Depth of soil fill =3.5 m,Diameter of the pile=30…

Q: A square pile group consisting 9 pile passes through a recently constructed soft deposits with qu =…

Q: 10 A pile of 40cm diameter and 18.5m -long passes through two layers and embedded in a third layer.…

Q: A pile group of 9 piles placed in 3 row, 1 m apart between rows, with 1 m spacing 1 m in…

Q: Determine the allowable bearing load of the pile shown in figure Q1 using all the possible methods…

A: The soil is cohesive. We will only need cohesive soil parameters.

Q: 1. A 3 X 4 group pile that are square in cross section (356 mm x 356 mm) as shown in the figure. The…

A: To determine the ultimate load-bearing capacity of the 3x4 pile group acting individually, we need…

Q: In a 16 (4 x4) piles group, the pile diameter is 0.4 m and center to center spacing of piles in the…

Q: A 400 mm diameter friction pile is embedded into 8 m homogeneous consolidated deposit. Cohesion…

Q: A group of driven piles are to be built in layered soils as shown in the figure below. Please…

A: For ϕ = 35o , Nq = 33.5 Assuming pile to be concrete, and for loose sand {as γ=120psf}; k = 1…

Q: Silty clay Y- i18 Iivn C,- 700 Ib/ft 20 ft Groundwater Plasticity index, PI = 15 table . Silty clay…

A: Given : Equation 9.45, fav = 0.02 pa(N60) Equation 9.46, fav = 0.01 pa(N60) Equation 9.47, fav =…

Q: Determine load carrying capacity of pile without considering critical depth concept. Diameter of…

A: Answer We know that the load bearing capacity of pile(Q) is given by combination of point Bearing…

Q: 14. If there are piles in a pile group foundation, the pile group effect coefficient n refers to ( )…

A: The correct answer is option A

Q: 2. Two cylindrical steel piles (P1 and P2) are to be driven along the shore. Two total stations were…

A: The angle between TS1 and TS2 is, α=tan-13414.175-3021.8328415.591-6523.709α=11°42'57.82''…

Q: Square concrete piles are arranged in 3 row by 4 column formation beneath the pile cap. These piles…

A: Given, Pile width (b) = 0.45 m Nc = 8

Concept explainers

Pricing Excavation and Backfill

Backfill, in construction, is the activity of returning the soil and gravel that are removed during building construction or using them again to toughen and support the foundation of the building or any other structural component.

Question

For a group of piles 3x5 with pile diameter is 0.4 m and centre to
centre spacing is 2.8 m.if the settlement of the single pile is 12 mm
.the settlement of the group is :
3 -
a)
41.9 mm
b)
17.1 mm
12.1 mm
146.4 mm
Boş bırak

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A 16 in diameter, 75 ft long drilled displacement pile is made of grout with f'c = 5,000 lb/in2. A steel ratio of 0.04 is to be used in the upper 30 ft, and a steel ratio of 0.001 for the remainder of the pile. Compute the modulus of elasticity for the upper and lower portions of this pile.
A concrete pile is 15 m long and has 406 mm diameter circular cross section. The pile is fully embedded in sand, for which the unit weight '( = 18 kN/m3 and the frictional angle 8 = 30°. i) Calculate the ultimate point load Qp ii) Determine the total frictional resistance Qs iii) Determine the total ultimate load ofthe pile.
A group of 9 piles of 26 cm diameter is arranged in a square configuration with a center-to-center spacing of 1.75 m. The length of the piles is 8 m. Unit cohesion of the clay is 93 kPa. Determine the ultimate group capacity of the pile group based on block failure. Assume adhesion factor of 0.65. Round off to two decimal places.
A concrete pile group 3x3 with spacing of 0.6m is used to support a wind turbine in a sand deposit. Individual pile diameter = 0.3 m and length=6m. A. If the allowable (working) lateral capacity for a single pile is 95 kN, what is the maximum allowable lateral deflection for each pile? B. Is the lateral deflection acceptable? Explain your answer in 1-2 sentences.
During geological investigation on a site, it was observed that subsoil contains 7.5 m depth of clay followed by some other incompetent layers. The consultant decided to design a friction pile group which should be economical and able to carry the anticipated load of 1.5 x 106 N excluding the weight of pile cap. Design and draw the plan of the most suitable friction pile group considering the following parameters:Cohesion intercept of clayey layer = 0.030 N/ mm2Factor of safety against shear failure = 2.25Weight of pile cap = 110000NPile diameter = 300 mm
During geological investigation on a site, it was observed that subsoil contains 7.5 m depth of clay followed by some other incompetent layers. The consultant decided to design a friction pile group which should be economical and able to carry the anticipated load of 1.5 x 10° N excluding the weight of pile cap. Design and draw the plan of the most suitable friction pile group considering the following parameters: = 0.030 N/ mm - 2.25 Cohesion intercept of clayey layer Factor of safety against shear failure Weight of pile cap = 110000N Pile diameter 300 mm %3D
A group of 9 piles of 29 cm diameter is arranged in a square configuration with a center-to-center spacing of 1.01 m. The length of the piles is 12 m. Unit cohesion of the clay is 80 kPa. Determine the ultimate group capacity of the pile group based on block failure. Assume adhesion factor of 0.69.
A helical pile with 12 in diameter flights and a 2 in square rod is to be installed to a depth of 30 ft in a silty clay. The undrained shear strength is 1,000 lb/ft2 and the groundwater table is at a depth of 40 ft. The individual helixes are located every 5 ft along the length of the pile, and the pile has an average weight of 100 lb/ft (including the embedded soil). Using a factor of safety of 3, determine the ASD allowable uplift capacity, Pup,a.
A precast concrete pile has size 40 cm x 40 cm, ultimate load carrying capacity of pile is 1200 kN, ☎ and a are 50 kN/m2 and 0.6 respectively what is length of pile.