*:For a certain mode, in a rectangular waveguide, propagation occurs for signalsInformation are not sufficient to decide OWhose frequency is above the cut off frequencyWhose frequency is below the cut off frequencyDepending on the dimensions of the waveguide and dielectric OThe dominant mode of propagation is preferred with rectangular waveguides* becausewe can use air as dielectric Oit is easier than other modes and leads to smallest dimension of waveguideit is easier than the other modesit leads to smallest dimension of waveguidenone of metioned

1) Cut off frequency is minimum frequency where propogation occurs in a waveguide So propogation…

*:For a certain mode, in a rectangular waveguide, propagation occurs for signals Information are not sufficient to decide Whose frequency is above the cut off frequency Whose frequency is below the cut off frequency Depending on the dimensions of the waveguide and dielectric The dominant mode of propagation is preferred with rectangular waveguides because we can use air as dielectric it is easier than other modes and leads to smallest dimension of waveguide it is easier than the other modes it leads to smallest dimension of waveguide none of mentioned

*:For a certain mode, in a rectangular waveguide, propagation occurs for signals Information are not sufficient to decide Whose frequency is above the cut off frequency Whose frequency is below the cut off frequency Depending on the dimensions of the waveguide and dielectric The dominant mode of propagation is preferred with rectangular waveguides because we can use air as dielectric it is easier than other modes and leads to smallest dimension of waveguide it is easier than the other modes it leads to smallest dimension of waveguide none of mentioned

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

IN rectangular waveguide, we know that in TM mode field, Ez (longitudinal field) is out f phase by 90 degree, why is it?
A 2 V signal is incident to the interface from a 75 Ohm region propagating to a 50 Ohm impedance region. What is the reflection coefficient? What is value of the incident, reflected and transmitted wave? What voltage would you measure on either side of the interface right after the signal goes through the interface. For the interface, I'm a little confused. I used a voltage divider and got V_transmitted = 0.8 and V_incident = 1.2. But shouldn't they be the same?
What is a waveguide? What is a slab waveguide? What is a planar waveguide? What is thin slab?
4. What are the types of power loss in a rectangular waveguide
What does the TE mean? Why does one have a 10 as subscript and the other mn? What is a broad and short dimension and a rectangular waveguide?
3) Solve the cutoff frequency for the first mode and second mode of WR975 Wave guide TABLE 7.1 Some Standard Rectangular Waveguides Waveguide de signation a (in) b (in) t (in) fe, (GHz) Frequency range (GHz) WR975 9.750 4.875 0.125 0.605 0.75-1.12 WR650 6.500 3.250 0.080 0.908 1.12–1.70 WR430 4.300 2.150 0.080 1.375 1.70-2.60 WR284 2.840 1.340 0.080 2.08 2.60-3.95 WR187 1.872 0.872 0.064 3.16 3.95-5.85 WR137 1.372 0.622 0.064 4.29 5.85-8.20 WR90 0.900 0.450 0.050 6.56 8.2–12.4 WR62 0.622 0.311 0.040 9.49 12.4–18
Two rectangular waveguides, one of them is an air filled with internal dimension 1? 2 cm2 and the other one is dielectric filled with internal dimension 1? 0.5 cm2. They have the same cut off frequency for the dominant mode. What is the relative permittivity of the dielectric material?
A 2 V signal is incident to the interface from a 75 Ohm region propagating to a 50 Ohm impedance region. What is the reflection coefficient? What is value of the incident, reflected and transmitted wave? What voltage would you measure on either side of the interface right after the signal goes through the interface.
What is field pattern in a. Rectangular waveguide?b. TE mode in rectangular waveguide?c. TM mode in rectangular waveguide?
Circular waveguides
Imagine a two-dimensional system in which a sinusoidal waveform is excited at the exact center of a circular plate. The standing wave pattern is established when the excited wave two-dimensionalwaveforms for a stable equilibrium pattern of constructive and destructive interference with the reflected waves from the edge of the circular plate. Draw what you expect the standing wave patterns to look like in this two-dimensional system for increasing resonant harmonics, n. Explain what characteristics of the oscillating plate affect the value of those resonancefrequencies, and what geometric properties of the plate affect the patterns.
4. Again, from the zigzag-path waveguiding model, explain why the group velocity is always slower than the phase velocity in a waveguide with a cutoff frequency.