following equation applies: V = IR. Outside of the linear range, V*IR, outside of the linear ranges where resistors are broken The resistor has a resistance of 100ohm, and a power rating of 250mW. 1) Sketch the plot (and label) of the i-v relationship for the resistor using only the linear range of the resistor. Determine the range of values for the voltage and current that the resistor operates as a linear element and note these simplified numerical values on the plot.

following equation applies: V = IR. Outside of the linear range, V*IR, outside of the linear ranges where resistors are broken The resistor has a resistance of 100ohm, and a power rating of 250mW. 1) Sketch the plot (and label) of the i-v relationship for the resistor using only the linear range of the resistor. Determine the range of values for the voltage and current that the resistor operates as a linear element and note these simplified numerical values on the plot.

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter7: Parallel Circuits

Section: Chapter Questions

Problem 3PP: Using the rules for parallel circuits and Ohmslaw, solve for the missing values....

See similar textbooks

Similar questions

The diagram in the figure shows a simple circuit consisting of a battery and a load consisting of two resistors.The battery voltage is UB = 56 V and the value of the resistors is:R1 = 1800R2 = 5400a) The ammeters in the circuit show the following value:A1 shows valueA2 shows valueA3 shows valueb) In the load, the effect developsc) The total resistance of the load is
A dc generator and a battery are connected to a resistive load RL in the figure below. For each, determine the value of RL for maximum power transfer to RL. Next is to determine RL to 75% efficiency
8 The figure is a graph of . Current Voltage the current across a voltage as a function of the potential difference through it the resistance as a function of the current across a component the current through a component as a function of the voltage across it O All three of the above (a), (b), and (c) are true O None of the above (a), (b), or (c) is true
2 The figure is a graph of ... 5 (5 Points) Current Voltage the current across a voltage as a function of the potential difference through it the resistance as a function of the current across a component the current through a component as a function of the voltage across it All three of the above (a), (b), and (c) are true None of the above (a), (b), or (c) is true
An example of Simple Resistive Circuits is ,
What is the equation of V1 in the figure shown if Vs = 200mV/div
Create a general procedure to solve any circuit DC circuit with any number of resistors.
How temperature effect conductivity? Explain with the help of following equation. m e'n7'
Which of the following statements regarding circuits are true? To find resistance in a parallel circuit, you must sum the individual resitances The direction of conventional current is the direction of positive charge flow. In a circuit, electrons flow from high potential energy (at the negative terminal) to low potential energy (at the positive terminal). When electricity is passed through a lightbulb, the electrons are 'used up' by the bulb. All voltages in a loop sum to 12V The current that flows into a resistor is the same as the current that flows out. To 'short circuit' something means there is an alternate path of less resistance for the current to flow. Switching on a light happens immediately because electrons move from the power source to the bulb incredibly quickly. A 'kilowatt-hour' is a unit of power, not energy.
Write an equation based on junction b. Using the current values, solve for the voltages across each resistor. Solve the current analytically.
the adjoining figure. This lamp can withstand a maximum voltage 3.0 v 0.4 9. Volt-ampere (V-I) charaeteristics of an incandescent lamp 16thd in and a maximum current 0.4 A. An infinite ladder network consisting a large number of these lamps is also shown in the figure given belo How much maximum voltage can be applied between the terminals A and B, so that no lamp gets damaged? (Use V5 = 2.2). Ans:x4.2V Hint: Curentin all bulls except first is
For the network shown in figure (3), if the switch is closed for 2usec and then opened for Susec, find mathematical expressions for vi and in of both periods of time and then plot the waveforms of vL and i as a function of time.