Fluid flows through the pipe into a rigid tank in the shape of a cube. During that process, heat is transferred out of the rigid tank and water leaks out of the tank such that mass balance of the control volume does not change. Show the correct final form of mass equation

Fluid flows through the pipe into a rigid tank in the shape of a cube. During that process, heat is transferred out of the rigid tank and water leaks out of the tank such that mass balance of the control volume does not change. Show the correct final form of mass equation

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Liquid in a fixed volume closed container isis mixed. X + 400 kJ of work is done to mix the propellerand 500 kJ of heat transfer from the vessel walls to the environment. The internal energy of the liquid in its final state is 660 kJ.As it is known, find the initial internal energy. Draw the system schematically and show the energy flow.(It is assumed that there is no kinetic and potential energy change.) (X=0)
There is a heated continuous stirred tank reactor shown below where the density is constant through out the system. On the other hand the volume of reaction mixture may vary. The thermal capacitance of the coil used to heat the tank is assumed to be negligible. There is a 2nd order elementary chemical reaction 2A → C taking place in the reactor. Cai Tai qa 2A ->C v „ro Tc Ac In the figure shown above Cai, Tai,qa is the inlet concentration of component A , inlet stream temperature and inlet volumetric flow rate, V is the volume of the reaction mixture, ro is the density through out the system. Tc, Ac and U are the coil temperature, surface area of the coil and heat transfer coefficient of the coil. Cc, T and Ca are the concentration of product C, temperature of the reactor and exit concentration of component A, qc is the outlet volumetric flowrate. The rate constant is assumed to be independent of temperature denoted as ko. The heat of reaction is denoted as AHrxn. Cp is the heat…
The cylindrical in the figure is filled with 31.4 m3 of water at t = 0. The radius of the tank is 1 m and its height is 10 m. There is an outlet line with a radius of 0.2 m at the bottom of the tank. a. What is the time required for half of the water in the tank to drain after the outlet line is opened?b. The flow velocity of water from the bottom of a water tank is related to the height of the water in the tank, and this relation is v² = 2gh where v: (m / s) linear flow velocity, g: gravitational acceleration (10 m / s2) and h: (m) height.
Initially tank I and tank II each contains 100 gal of brine, tank I having 200 lb salt and tank II 50 lb of salt in solution. Brine runs at 2 gal/min from tank I to tank II through one pipe and at 3 gal/min from tank II to I through another pipe. The brine is kept well stirred. How much salt (in lb) will be in the second tank after 50 min?
Q1- A pressure-relief valve contains a poppet with an area of 5 cm2 on which the system pressure acts. During assembly, a spring with a spring constant of 3700 N/cm is installed in the valve to hold the poppet against its seat. The adjustment mechanism is then set so that the spring is initially compressed to 0.45 cm from its free-length condition. In order to pass full pump flow through the valve at the pressure-relief valve pressure setting, the poppet must move 0.25 cm. ( A ) The cracking pressure of the valve will be *
Q4/ How much heat is required to raise the temperature of 30 Kg air in the room from 5c'to 20c'when a heater is used to heat this room ,under this conditions the specific heat capacity of air=1000 J/Kg.K
Q1- A pressure-relief valve contains a poppet with an area of 5 cm2 on which the system pressure acts. During assembly, a spring with a spring constant of 3700 N/cm is installed in the valve to hold the poppet against its seat. The adjustment mechanism is then set so that the spring is initially compressed to 0.45 cm from its free-length condition. In order to pass full pump flow through the valve at the pressure-relief valve pressure setting, the poppet must move 0.25 cm. ( A) The cracking pressure of the valve will be * O 4.62 MPa 3.33 MPa 6.45 MPa O None of the above
Two incompressible fluids of densities p, and p2 are mixed in a square tank. Fluid-1 is pumped into the tank at the rate of 24 kg/s, and fluid-2 is pumped into the tank at the rate of 0.050 m³/s. After complete mixing, the mixture leaves the tank through pipe-3. You are given: P1 = 800 kg/m³, P2 = 1000 kg/m³, 0 = 60°, B = 0.9 m. a) Define your control volume, indicate control surfaces and number each active control surface. b) Determine the mixture density and the volume flowrate out of the tank if the mixture level in the tank is constant. c) Determine the mass and volume flowrates out of the tank if the mixture level in the tank is decreasing at a rate of 0.04 m/s. Note that the density of the mixture will be the same as in part b. В В Mixture Fluid-1 Pipe-3 Fluid-2
A pressure relief valve contains a poppet with a 4.20 cm2 area on which system pressure acts. During assembly a spring with spring constant of 3200 N/cm is installed in the valve to hold the poppet against its seat. In order to pass full pump flow through the valve at the PRV pressure setting, the poppet must move 0.3 cm from its fully closed position. What should be the initial compression of the spring in the PRV if the full pump flow pressure is to be 40% greater than the cracking pressure?
A rigid vessel of volume 0.5m 3 (Vessel X) containing hydrogen at 200K and a pressure of 60kPa is connected to a second rigid vessel of volume 0.8m 3 (Vessel Y) containing Argon at 300K at a pressure of 40kPa. A valve separating the two vessels is opened and both are cooled to a temperature of 150K. What is the final pressure (kPa) in the vessels?
Methanol (SG=0.792) is contained in a large tank under a pressure of 350000 Pa absolute. When a valve on the bottom of the tank is opened, the methanol drains freely though a 0.02 m ID tube whose outlet is 7.00 m below the surface of the methanol. The pressure at the outlet of the discharge pipe is 101325 Pa. Some useful constants and conversions: g = 9.8 m/s2 , Pref = 1000 kg/m3 . a. Draw the system. Label points I and 2 (where you will define A= 2-1) and label the variables with values b Write the general form of the energy balance. Cancel out negligible terms, and state the keyword/assumption to justify. Simplify to the resultant energy balance. c.) Assume the diameter of the tank is very big compared to the drain tube velocity, which make the velocity of liquid in the tank equal to zero. Estimate the methanol discharge velocity in the drain tube in m/s. *hint: divide your EB by m to eliminate m and V. Recall, n = pV = pvA and = v/m=1/p
Help me please