Flow between coaxial cylinders and concentric spheres. (a) The space between two coaxial cylinders is filled with an incompressible fluid at constant temperature. The radii of the inner and outer wetted surfaces are «R and R, respectively. The angular velocities of rotation of the inner and outer cylinders are , and 2. Determine the velocity distribution in the fluid and the torques exerted by the fluid on the two cylinders needed to maintain the motion. (b) Repeat part (a) for two concentric spheres.

Flow between coaxial cylinders and concentric spheres. (a) The space between two coaxial cylinders is filled with an incompressible fluid at constant temperature. The radii of the inner and outer wetted surfaces are «R and R, respectively. The angular velocities of rotation of the inner and outer cylinders are , and 2. Determine the velocity distribution in the fluid and the torques exerted by the fluid on the two cylinders needed to maintain the motion. (b) Repeat part (a) for two concentric spheres.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Sketch the streamlines and equipotential lines for fluid motion in which the complex potential is given by (a) 2 + 2z. (b) z, (c) e, (d) cos z.
AND 306 mm 240 mm 240 mm 46.6 mm PROBLEM 3.9 The tailgate of a car is supported by the hydraulic lift BC. If the lift exerts a 125-N force directed along its center line on the ball and socket at B, determine the moment of the force about A.
The hydraulic crane is used to lift the 1400-lb load. Determine the force in the hydraulic cylinder AB and the force in links AC and AD when the load is held in the position shown. B 30° 8 n 1 t 120 D 70° 7 R
Blocks A and B have a mass of 50 kg and are connected by a rigid bar of negligible weight. Furthermore, the coefficients of static and dynamic friction on all surfaces are respectively 0.3 and 0.25. The angle θ corresponds to 30°. Determine: The largest value of P for which the blocks do not move.
Q2) The slotted arm pivots about O and maintains the relation between the motions of sliders A and B and their control rods. Each small pivoted block is pinned to its respective slider and is constrained to slide in its rotating slot. Show that the displacement x is proportional to the reciprocal of y. Then estab- lish the relation between the velocities va and vg. Also, if va is constant for a short interval of motion, determine the acceleration of B. 2:28 /
The water (density =1000 kg/m3) leaves the nozzle (area of the nozzle=D0.01 m ). Assuming steady, incompressible, and neglect the weight of jet and the plate, change in elevation is also neglected. Determine the horizontal reaction force (N) on the support. Note that the stagnation tube has a fluid of specific gravity S=5.6 and the deflection of the fluid in stagnation tube is 50 cm. stagnation tube angle=40 deg 50 cm Nozzle angle =20 deg
8/111 We will see when we study friction in Chapter 6 that a very large force T can be required to raise the 10-kg body when the cable is wound around a fixed rough cylinder as shown. For the static- equilibrium values shown, determine the force and moment reactions at point O. The 0,.3-m di- mension refers to the point A where the cable loses contact with the cylinder. Neglect the weight of the fixed cylinder. Ans. O, = -14 900 N, O, = 24 400 N %3D 8890 N M = - 19 390 N m, My = - 12 120N m x, M, 857 N.m T = 30 kN %3D 30° 20 0.8 m 30 mm 0.3 m 10 kg Problem 3/111
Complex potential function of flow is given; F(z) = -5i.ln(z) +Uz Obtain the velocity fields and pressure distributions of the flow.
A Pole is connected to the wall with a ball and socket joint and also supported by two cables. The weight of the pole is 80 lb. Forces F1 and F2 are applied to the pole at point D. F1 is + 120j lbs. and F2 is -340k llbs. (a) Draw the free body diagram of the pole, make a list of all of the coordinates for each point, and write your assumptions.(b) Write the full set of equilibrium equations for the pole.(c) solve for the tension in the cable CG and DF and for the reaction forces at A. The two cables are separate.Augmented Matrix for RREF. When you copy your Augmented Matrix into MatLab, remember to only use the same number of equations (rows) as you have unknown values.
Replace the three forces shown by an equivalent force-couple system at point A. If the forces are replaced by a single resultant force, determine the distance d below point A to its line of action. 190 N 710 mm 710 mm 710 mm 255 N Answers: Force-couple system at A. The force is positive if to the right, and the couple is positive if counterclockwise. R= i N M = Single resultant force. 120 N N•m
The force system shown consist of a counterclockwise couple of 720 N-m plus a 1200 N force through the origin O, directed down to the left as specified. Determine the (a) distance between the forces and (b) intercepts of the single force at A(a,0) and B(0, b).
Collars A and B slide along the fixed right-angle rods and are connected by a cord of length L - 7.5 m. Determine the acceleration of collar B when y - 2.9 m if collar A is given a constant upward velocity va - 1.39 m/s. The acceleration of B is positive if to the right, negative if to the left. Answer: ag - m/s?