Calculate the volume flow rate in gallons/min 6.FLOWt.2inschedule 4oOIL (sq =0.80)PIPE24in4schechule 40pipcA6in81nfWATER

Answered: Image /qna-images/answer/ec9b6fc4-69d4-41dc-9f96-9c9bb4d329c8.jpg

Answered: FLOW 2in Schedule 40 OIL (ug =0.80)…

Engineering

Civil Engineering

FLOW 2in Schedule 40 OIL (ug =0.80) PIPE 24in 4 ih schechule 40 pipe 6in fWATER 十A

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Pipe cаrying water is having diameters 20 cm and 10 cm at the cross-sections 1 and 2 respectively.…

A: Given: Diameter at 1, d1 = 20 cm = 0.2 m Diameter at 2, d2 = 10 cm = 0.1 m Velocity of water at 1,…

Q: PROBLEM 02: Water is flowing at a rate of 7 ft^3/s, and it is assumed that the head loss from the…

Q: 1. Water is being pumped from reservoir A to reservoir B. Taking h-0.006m/m, find the pump…

A: Q= discharge = 2.5 m3/s 1 horse power= 746 watt

Q: A S floning upward through a venturi meter as shonn- O.984. What is the Qwnssy rate of flow…

A: Solution: 2 part solution: Given Data: Discharge coefficient=0.984 Flow rate (Q)=? Glycerine, s=1.26…

Q: The rate of flow in reservoir C is 150li/sec. Elevation of of reservoir A is 10, that of B is 132m…

Q: Lateral drain 16 km length serve 28000 donum by 6 collectors D1, D2. D6 as shown in figure 11-50,…

A: branch canal 15 km length compensation factor F=25% C1:3500d 03:35000 C5:50000 O km 3 Km 7 Km 11 Km…

Q: Y water is transpor ted at 75°F (v- 10$ for 1500ft .in (l.s)in - dianeter wrought iron horizontal…

A: Given: T = 75 F, D = 1.5 in, Q = 0.1 m3/sec, We need to determine the pressure drop over 1500 ft…

Q: Air at 20°C and approximately 1 atm fl ows through asmooth 30-cm-square duct at 1500 ft3/min. The…

A: Following is the given data:

Q: Example: Horizontal pipe system passing oil y = 7.18kN/m³, U= 8.9 * 10-5, diameter of each pipe…

A: Given:- The unit weight of the oil = 7.18 kN/m3 The value of U = 8.9×10-5 The diameter of each…

Q: Q2: Determine the dimension of flocculator tank to treat 50 m3/min of water with detention time…

A: The rate at which water is being treated by the tank, Q = 500 m3/min Detention time of tank, t = 30…

Q: . Water is being pumped from reservoir A to reservoir B. Taking h-0.006m/m, find the pump horsepower…

A: given discharge= Q= 2.5 m3/s D= 0.5m L=1500m hp = pump head pump efficiency = η = 85%

Q: 2- The most common system üsed föP C- Combined system Gravity system 3- Free avilable chla A- B-…

A: Generally for water supply, water is supplied by gravity and pumping both together. Hence it is…

Q: Your assigned problem: If the water surface elevation in reservoir B is 110m, what must be the water…

Q: culturable command 25. The area for a distributary channel is 20,000 hectares. Wheat irrigation is…

Q: Waters enter a pump through a 25 cm. dia. Pipe at 35Kpa. It leaves the pump at 140 kPa through a 15…

A: Given, At entryd1=25 cmP1=35KPaat exitd2=15 cmP2= 140KPaFlow rateQ=150l/s.

Q: 5. Determine the total discharge in the pipes. N = 0.013 El0 di 200mm El.0 dz: 200 mm L2 B00 m

Q: Water flows under a sluice gate on a horizontal bed at the inlet to a flume. The water depths at the…

Q: m 2. Find the maximum amount of w n be pumped from the well in an aqu /day and S = 8 x 10-³ in order…

A: Jfjgpjg gigg jihohohohoghihohohoh Hobobohoh

Q: El. 200 mA A Res. H-W Pipe B Pipe E pipec → Negleet minor losses → Pipes B, C, and E are all have: L…

A: Vc = 5m/s

Q: A/ Estimate Q in. B/ In the pipe systems show, find the distribution of flow, with a friction factor…

A: Given that friction factor is 0.0165 Length and diameter of pipes are shown in the figure We are…

Q: A,B and C connected in seies

Q: 43. A circular clarifier is being designed to receive a flow of 4.8 MGD. If the circular depth is…

Q: Select a low operating-cost pump (select n and Dp) Plot curves of: (Head vs. Q; Eff. vs. Q ; Power…

A: Bernoulli's principle is generally the pressure of a fluid to its elevation and its speed. It can be…

Q: (sp.gr. 5) and an air space of 1.0m above the oil. If the pressure at the bottom of the tank is Pa,…

Q: Tor flows nate 28 Lis Find pump Power Eし、60M L00 mm ち0 mm El. 30MH

A: Given data Pump Discharge Elevation heads at two points Length

Q: For the Pipe shown Q=4250 gallons per minute (gpm), P1=132 kPa and P2 = 211 kPa. If the pipe carries…

Q: A 600m long pipe with a diameter of 600mm has a headloss of 1.20m. Detemine the following: a.)…

A: Given data- Length of pipe (L) = 600 m Dia of pipe (D) =600 mm = 0.6 m Headloss (hf) = 1.20 m

Q: (b) Three pipes 1, 2, and 3 are 300 m of 30-cm-diameter, 150 m of 20-cm-diameter, and 250 mof…

Q: Pump delivers 0.05 m/s flow of 40°C water, and the intake pipe L = 4m & D = 20 cm. The pump intake…

A: Option (C) is correct.

Q: A 10 ft by 15 ft rectangular cistern (storage tank for rainwater) has its top 30 ft below ground…

A: Given, Tank dimensions = 10 ft x 15 ft x 30 ft Unit weight (γ) = 62.4 pcf

Q: 1.) Given: Discharge thru the siphon = 280 lit/sec; siphon diam. = 200mm %3D b = 2m; elev. at C =…

A: To determine the elevation of point A apply Bernoulli's equation between C and A.…

Q: 8. As shown, water (15°C) is draining from a tank through a galvanized iron pipe. The pipe length is…

A: Given -

Q: For the setup shown given k1 = 2.4* 10-5 m/min and k2 = 1.0*10-5 m/min, the cross-sectional area is…

Q: Three pipes A,B and C coonected in seies discharges 160 L/s of water. The properties of pipe: for…

Q: Main Pipe :35 m, 90 deg bent Community B Community A 30 m 25 m Pump Pump ym 10 m 10 m Fig .2:…

A: Given, Discharge(Q) = 45m3/s Velocity(V) = 1.235 m/s Area(A) = Q/V = 45/1.235…

Q: Manning n= a.015 - bettem slepeu Si= c.0004 flow rate Canstant " Q"- Bo00 cfS . betermine the…

A: Q = 8000 cfs = 8000 * 0.30483 = 226.535 m3 /s

Q: 5. A- Q 3 ft THE LEVEL SY PHON REGULATES THE A OF WATER IN TANK DETERM) NE Q 士N Cfs FOR THE 3 エNCH…

A: Discharge: The volume of fluid that is passing through a section within a certain time is known as…

Q: 4) Water is flowing in a 300 mm circular pipe with a discharge of 0.250 m/s. Find the Reynold's…

Q: 2. Average 3. C= 120 sure 4. Length of main line 100m 5. Number of sprinklers, N=18. 6. Discharge of…

Q: Hydraulics of Sprinkle Example// Select the discharge of (126 m3/

A: 1.For a pressure calculation , we have following relationQ=kp0.5where, p is the pressure in bar, Q…

Q: 9. A 20-HP pump is employed to deliver water from a stream to an open air holding tank located 1500…

A: An exhaust pipe with a valve and a spout through which water can be drawn from water holes. fire…

Q: Water level in three reservoirs at elevation 126m, 109m and 100m are connected by pipes AN, BN, NC…

A: Water level in reservoir , A=h1=126m Water level in reservoir B=h2=109 m Water level in reservoir…

Q: Q2/ A cross regulator is designed to pass a normal full supply of discharge of 2.5 m/sec with 0.1m…

A: Solution Given Data Q=2.5 m3/s C1= 0.577 C2= 0.8

Q: Determine the division of flow and head loss from A to B, if the given f=0.010 for all pipes. Note…

Q: Calculate the discharge (Q) of each Pire Dに1m O2=0.6m D3=1.2 m E :0.013 fz =0.02 f3=0.023 c0.o13…

Q: trapezoidal as defined below and conveys a discharge of 200 cfs. Use the standard step method. 1 n =…

A: Given n= 0.030 S= 0.0050

Q: Determine the division of flow and head loss from A to B, if the given c = 180 for all pipes. Note…

Q: Three pipes A,B and C coonected in seies discharges 160 L/s of water. The properties of pipe: for…

Q: Discharge (Y cumec) and Stage (x m)

A: X Y X Y X Y X Y 24 1576.86 9 247.26 18 905.7 19 1004.66 8 199.9 4 62.06 20 1108.78 2 24.1 4…

Concept explainers

Unit Conversion

Standard units are also called SI units. SI units are used for measuring a physical quantity satisfying certain conditions. There are two types of units: fundamental units and derived units. Fundamental units are physical quantities that are independent, that is, they do not depend on other quantities like mass, length, or time. There are plenty of quantities in our lives which need to be measured and compared. Measuring is the comparison of a particular physical quantity with its reference value. A unit is a measure of a fixed physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with.

Question

100%

Calculate the volume flow rate in gallons/min

6.
FLOW
t.
2in
schedule 4o
OIL (sq =0.80)
PIPE
24in
4
schechule 40
pipc
A
6in
81n
fWATER

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Soilo the Sol Set Shown, 30 cm Oht, le, he @all ponts 36 cm 1Ou 10 Cm @ PwP @ Ports B, E,anda 10 Cm 10 Cm 10 Cm 10 Cm 10 Cm 10 C- Soile Az5 A datun
Cusenusan/DounbadTelegram20Desktop/Weighted20roughnesa20coefficient20151 pdt al O A*I D B ? + - H.W. Q1) Water is flowing in three side-by-side pipes of diameter (1.8m) each. The Manning's (n) and the bed slope of each pipe are (0.017) and (1:1000) respectively. The water depth in each pipe is (1.6 m). After the development, the discharge above is expected to increase by (25%), and the engineers have decided to replace the three pipes by a trapezoidal channel. The new channel should have (n= 0.013) with the same bed slope , B = 1.15 y , and z=1. Design the cross section of the new channel. II
CAsensusanyDounbad Telegram20Desktop/Weighted20roughness20coetfficient20151 pdf al O H.W. Q1) Water is flowing in three side-by-side pipes of diameter (1.8m) each. The Manning's (n) and the bed slope of each pipe are (0.017) and (1:1000) respectively. The water depth in each pipe is (1.6 m). After the development, the discharge above is expected to increase by (25%), and the engineers have decided to replace the three pipes by a trapezoidal channel. The new channel should have (n= 0.013) with the same bed slope , B = 1.15 y , and z=1. Design the cross section of the new channel. II >
2 T © t - Q1/Define flood routing. Explain its practical use. ||| = فلاتر 0 إضافة شرح... x mum
water runs 555t and hight 1o ft1at the rate of g ftmin How fast is into Conincal tank, with radius of base the water level riSing when the water is
3) en= 24!-0" SIMPLY 8'-0" TYP %3D SUPPORTED ら000 psi fィ= 6o Ksi WoL= 29,5" 1.25 kLF 3-#9 :CHECK Er >0.005 FIND AレLOWABし Wn USE 1.2ウ+ioL
2. Analyze He indekrminak benm shown. ET is unstunt. (Wie three - mment eguatins) 90 low 114 kN 24 LN/m tt 2m Im' 2m
PANILALAD, FHAECY ARCH 3256 PLOT ASSUMY NE WEIGHT 8KN 2M V & M THAT 7KN £--3M-1--- HAE D THE PEAM NEGALIGIBLE 7M- WEIGHT ьм क् 6KN 1 24
Solve it plz early ok
ipe Network): 0.225 cu.m./s A 0.1125 cu.m./s L0.1125 cu.m./s Pipe Pipe Length (m) Diameter (cm) 30 30 K АВ 1 915 BC 610 AD BE CF 3 460 460 25 4 20 25 460 915 DE 6. 20 EF 7 610 20 DG 305 25 GH 305 25 GH 10 1525 30 *** Correction: Pipe 9 = Pipe FH close Get live help whenever you need from online tutors!Try bartleby tutor todayarrow_forward Oh no! Our expert couldn't answer your question. Don't worry! We won't leave you hanging. Plus, we're giving you back one question for the inconvenience. Here's what the expert had to say: Hi and thanks for your question! Unfortunately we cannot answer this particular question due to its complexity. We've credited a question back to your account. Apologies for the inconvenience. Ask Your Question Again 27 of 30 questions left this cycle Renews on Dec 25, 2021 Question A simple pipe network is shown in the figure below. Determine the actual discharges in each pipe using the Hardy-Cross method. With the help of a…
B) When water flows through a pipe hauing a diameker of (an ond it showr a head lass of Cht), whet witl happen to its velocity, discharge, and hea) loss after it through the Contracted port of Ven ture meter w hich has a diameter of (az) where di7dz? (decrouer Passes E increases, or remeins con stont).
Please answer nos. 4, 5 and 6 N=289 M=332 L=17