Florida Electrical Transmission Company has to supply the demand of four companies in different hours. Calculate following: (i) Diversity Factor (ii) Units generated/Day (iii) Load Factor. Company name SLVQ МТЕ WWLE MREB TIME PERIOD 8AM-6PM 6АМ-10AM бАМ-10AM 10AM-6PM Then бРМ-6AM 250KW 150KW 100KW 150KW DEMAND

Florida Electrical Transmission Company has to supply the demand of four companies in different hours. Calculate following: (i) Diversity Factor (ii) Units generated/Day (iii) Load Factor. Company name SLVQ МТЕ WWLE MREB TIME PERIOD 8AM-6PM 6АМ-10AM бАМ-10AM 10AM-6PM Then бРМ-6AM 250KW 150KW 100KW 150KW DEMAND

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.64P: The per-unit equivalent circuit of two transformers Ta and Tb connected in parallel, with the same...

See similar textbooks

Similar questions

The figure below shows the one-line diagram of a four- bus power system. The voltages, the scheduled real power and reactive powers, and the reactances of transmission lines are marked at this one line diagram (The voltages and reactances are in PU referred to 100 MW base. The active power P2 in MW is the last three digits (from right) of your registration number (i.e for the student that has a registration number 202112396, P2 =396). [10] Starting from an estimated voltage at bus 2, bus 3, and bus 4 equals V2 (0) = 1.15<0°, V3 = 1.15 < 0°, V4 1.1< 0°. 1- Specify the type of each bus and known & unknown quantities at each bus. 2- Find the elements of the second row of the admittance matrix (i.e. [Y21 Y22 Y23 Y24]). 3- Using Gauss-Siedal fınd the voltage at bus 2 after the first iteration. 4- Using Newton-Raphson, calculate: |- The value of real power (P2), at bus 2 after the first iteration. Il- The second element in the first row of the Jacobian matrix after the first iteration. 2 P2…
The per unit impedance of a generator on a 60 MVA, 20 kV base is j0.09 p.u. The per unit impedance to a 100 MVA, 20 kV base will be (a.) j0.054 p.u. (c.) j 1.5 p.u. (b.) j0.54 p.u. (d.) j0.15 p.u.
Select generator rating as base value
The one-line diagram of a simple power system is shown in Figure below. The neutral of each generator is grounded through a current-limiting reactor of 0.25/3 per unit on a 100-MVA base. The system data expressed in per unit on a common 100-MVA base is tabulated below. The generators are running on no-load at their rated voltage and rated frequency with their emfs in phase. G Stark Item Base MVA Voltage Rating X' x² 20 kV 20 kV 20/220 kV 20/220 kV 100 0.05 0.15 0.15 0.10 0.10 220 kV 0.125 0.125 0.30 0.15 0.25 025 0.7125 0.15 100 100 0.15 0.05 0.10 0.10 0.10 100 0.10 100 100 Lu La 220 kV 0.15 220 kV 0.35 100 A balanced three-phase fault at bus 3 through a fault impedance Zf= jo.I per unit. The magnitude of the fault current in amperes in phase b for this fault is: Select one: A. 345.3 B. 820.1 C. 312500 3888888 产产

1. FIGURE 52 shows the one-line diagram of a simple three-bus power system with generation at bus I. The voltage at bus l is V1 = 1.0L0° per unit. The scheduled loads on buses 2 and 3 are marked on the diagram. Line impedances are marked in per unit on a 100 MVA base. For the purpose of hand calculations, line resistances and line charging susceptances are neglected a) Using Gauss-Seidel method and initial estimates of Va 0)-1.0+)0 and V o)- ( 1.0 +j0, determine V2 and V3. Perform two iterations (b) If after several iterations the bus voltages converge to V20.90-j0.10 pu 0.95-70.05 pu determine the line flows and line losses and the slack bus real and reactive power. 2 400 MW 320 Mvar Slack 0.0125 0.05 300 MW 270 Mvar FIGURE 52
b) The one-line diagram for a simple power system is given in Figure 1(b). į. Draw the impedance diagram of the system. i. Construct the bus admittance matrix, Xeus and bus impedance matrix, Zous of the system. I. Evaluate the fault current, bus voltages and line current during the flow when a balanced three-phase fault occurs on bus 1. bus 1 bus 2 j65 N G G 25 MVA 25 MVA 13.8 kV 15% 13.2/69 kV 11% 25 MVA 69/13.2 kV 11% 15 MVA 13 kV 15% Figure 1(b) m
7. In the circuit below write the loop equations and set up (not solve) the matrix equation for the load current. Wiso 150 75 28 100
Figure shows a generator connected to a metropolitan system (infinite bus) through highvoltage lines. The numbers on the figure indicate the reactances in p.u. Breakers adjacent to afault on both sides are arranged to clear simultaneously. Determine the critical clearing anglefor the generator for a 3-phase fault at the point P when the generator is delivering 1.0 p.u.power. Assume that the voltage behind transient reactance is 1.2 p.u. for the generator andthat the voltage at the infinite bus is 1.0 p.u.
With the same transformer banks as in Problem 3.47, Figure 3.41 shows the oneline diagram of a generator, a step-up transformer bank, a transmission line, a stepown transformer bank, and an impedan load. The generator terminal voltage is 15 kV (line-to-line). (a) Draw the per-phase equivalent circuit, aounting for phase shifts for positive-sequence operation. (b) By choosing the line-to-neutral generator terminal voltage as the reference, determine the magnitudes of the generator current, transmiss ion-line current, load current, and line-to-line load voltage. Also, find the three-phase complex power delivered to the load.
Consider the oneline diagram shown in Figure 3.40. The three-phase transformer bank is made up of three identical single-phase transformers, each specified by X1=0.24 (on the low-voltage side), negligible resistance and magnetizing current, and turns ratio =N2/N1=10. The transformer bank is delivering 100 MW at 0.8 p.f. lagging to a substation bus whose voltage is 230 kV. (a) Determine the primary current magnitude, primary voltage (line-to-line) magnitude, and the three-phase complex power supplied by the generator. Choose the line-to-neutral voltage at the bus, Va as the reference Account for the phase shift, and assume positive-sequence operation. (b) Find the phase shift between the primary and secondary voltages.
Consider three ideal single-phase transformers (with a voltage gain of ) put together as three-phase bank as shown in Figure 3.35. Assuming positive-sequence voltages for Va,Vb, and Vc find Va,Vb, and VC. in terms of Va,Vb, and Vc, respectively. (a) Would such relationships hold for the line voltages as well? (b) Looking into the current relationships, express IaIb and Ic in terms of IaIb and Ic respectively. (C) Let S and S be the per-phase complex power output and input. respectively. Find S in terms of S.
The per-unit equivalent circuit of two transformers Ta and Tb connected in parallel, with the same nominal voltage ratio and the same reactan of 0.1 per unit on the same base, is shown in Figure 3.43. Transformer Tb has a voltage-magnitude step-up toward the load of 1.05 times that of Ta (that is, the tap on the secondary winding of Tb is set to 1.05). The load is represented by 0.8+j0.6 per unit at a voltage V2=1.0/0 per unit. Determine the complex power in per unit transmitted to the load through each transformer, comment on how the transformers share the real and reactive powers.