Find the ventical moyement K 120 kN og Piy Stec Aluminum 4m 3m A 3m Im Steel A= 600 mm E = 200 6N/m? P= 120 kN Aluminum A=900 mm2 E = 70 GN/m2 Ans. must be in mm

Q: find the centroid of the cross section and plane

A: Given data in question Dimensions  To find out  Centroid Note A = total area  X= centroidal distance…

Q: 300 mm 30° 300 mm 300 mm Can some one please label the projection of F and the rest of the…

A: Solution: The force vector F and uOA:

Q: 4m 2m 2 m 4m 2 m

A: Find centroid of given section

Q: Provide the sectional front view, looking at the direction X, draw the top view, and left-side view…

A:

Q: Determine the number of divisions required on the vernier scale, if it is combined with the main…

A: given- least count of main scale=0.5 mmleast count of combination of direct vernier=0.05 mm

Q: d = 4" %3D x' b = 4" %3D B = 8" %3D H = 8" h = 4" d = 4"

A:

Q: y -180 mm -r = 100 mm X 50 mm

A:

Q: In detail, write about the introduction to 3D Shearing transformation.

A:

Q: Given: The two-dimensional shape shown below y 10 m 10 m semi-circle y Required: Find the vertical…

A:

Q: 100 mm 150 mm

A:

Q: entification: Classify the following beams, frames, and/or trusses as statically determinate,…

A: As per guidelines we need to answer only first thre subparts of question so please repost rest…

Q: Determine the magnitude and the direction angles of a vector (V) and draw in the space provided if…

A:

Q: Pb. Classify trees on the basis of Strength and Structure. Provide a short description in chart…

A: Trees can be classified into two types based on strength : 1 - Endogeneous trees 2 - Exogeneous…

Q: Determine the centroid coordinates (x̄ , ȳ) for the solid and homogeneous beam section shown in…

A: Determine the centroid coordinates (x̄ , ȳ) for the solid and homogeneous beam section shown in…

Q: Write the formula for the effective length factor?

A: The effective length factors of columns  plays major role in the design of compression members.…

Q: e two graphical representations of Mohr’s Circle by hand.

A:

Q: Define deflection angles.

A: A deflection angle is an angle between the onward extension of the previous leg and the line ahead.…

Q: Given the front view and the right-side view of the object, draw the top view and isometric view.

A:

Q: Given the top view, front view, and right-side view, draw the isometric view of the figure.

A:

Q: but I nee

A: Draw the figure Consider a differential element of size dy

Q: find the x bar at the location of centroid along y axis

A: To find x bar

Q: Find the centroidal distances from x axis and y axis

A: Consider the figure,

Q: Determine the cross sectional area of the given cross section notes: LEFTMOST LEFT CENTER RIGHT…

A:

Q: Find the centroid of square from bottom of X axis having dimension 8 mm *8 mm

A:

Q: Q5. Determine the resultant magnitude of the hydrostatic force that water exerts on the wall along…

A:

Q: 10. 45 8.3 SUPPORT BRACKET 100 33 10 10 25 -

A: Question being asked here is to draw the ISOMETRIC VIEW for the given projections And the given…

Q: Recall we applied the trapezoidal rule to determine the area of the shape given.

A: Solution;

Q: The sides of a rectangle are 42cm and 59cm. Find its diagonal? *

A: The given question comes under surveying subject of civil engineering, in the given question sides…

Q: e shape factor for the section as shown -3d 3d - fe 2d

A:

Q: Find the centroid of the composite figure ABCDEF (in the image).

A:

Q: Define matrix's diagonal, off-diagonal, subdiagonal, and superdiagonal elements. Illustrate each.

A: An n×n matrix, or a matrix with the same number of columns as rows, is known as a square matrix.

Q: Find the centroid.

A:

Q: Please refer to the attached drawing. For the given case, do the following: a. At points 1 and 2…

A: a) The labelled figure is shown below:

Q: For each condensed structural formula, write a line- angle formula.

A:

Q: 100 N 100 N 100 100 150 250

A:

Q: Below in Figure is an isometric drawing of a component. Draw in First Angle Projection the…

A: Question being asked here to draw the first angle projection in which the drawing pattern is…

British Gravitational Bg System Of Units

Measuring is the comparison of a particular physical quantity with its reference value. A unit is a fixed physical quantity. The length is a physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with.