Show the step-by-step process. Do not use shortcut methods. Make it as detailed as it can be. Find the value of the following dimensionless group from the given data.a) The Froude number, Nr„for the system where: v =Lgvelocity of 20 cm/s, L =length of 6 ft, and g =acceleration due to gravityb) The Schmidt number, Nsc„for the system where: u = viscosity, M/LO = 12 centipoise (cP), Dv =pDy*1P = 1 g/cm-sdiffusivity, L?/0 = 745 cm?/hr, p = density, M/L3 = 30 kg/ft3c) The Reynold's number, NReDvpfor the system where: D = 14 in, v = 26 m/s, p = 3 kg/mL, µ = 107 g/ft-hr

Find the value of the following dimensionless group from the given data. a) The Froude number, NEr „for the system where: v = velocity of 20 cm/s, L = length of 6 ft, and g = %3D Lg acceleration due to gravity b) The Schmidt number, Nsc „for the system where: µ = viscosity, M/LO = 12 centipoise (cP), Dv = pDy *1P = 1 g/cm-s diffusivity, L2/0 = 745 cm²/hr, p = density, M/L³ = 30 kg/ft3 c) The Reynold's number, NRe Dvp P, for the system where: D = 14 in, v = 26 m/s, p = 3 kg/mL, µ = 107 g/ft-hr

Find the value of the following dimensionless group from the given data. a) The Froude number, NEr „for the system where: v = velocity of 20 cm/s, L = length of 6 ft, and g = %3D Lg acceleration due to gravity b) The Schmidt number, Nsc „for the system where: µ = viscosity, M/LO = 12 centipoise (cP), Dv = pDy *1P = 1 g/cm-s diffusivity, L2/0 = 745 cm²/hr, p = density, M/L³ = 30 kg/ft3 c) The Reynold's number, NRe Dvp P, for the system where: D = 14 in, v = 26 m/s, p = 3 kg/mL, µ = 107 g/ft-hr

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

We have a rectangular piece. We wish to manufacture a parallel slot along thepiece in a vertical milling machine and 50 cm from the edge. The width of the slot is 40 mm. TheDepth of the slot is 25 mm. For this, several rough cutting steps and aFine cut with a depth of 0.20 mm. The depth for each of the steps ofrough cut is limited to 1.75 mmAditional information:What is the number of blades used for the rough cutting steps?What is the number of blades used for the fine cutting step?
7. What is the difference between a basic process and a secondary process? 8. What is a route sheet?
Quickly cover the many kinds of interruptions and then illustrate their importance to the machine with a concrete example.
Karl Knapps, Inc., has received the following orders: Period 1 2 3 4 5 6 7 8 9 10 Order size 0 40 30 40 10 70 40 10 30 60 The entire fabrication for these units is scheduled on one machine. There are 2,250 usable minutes in a week, and each unit will take 65 minutes to complete. Develop a capacity plan, using lot splitting, for the 10-week time period.
A mectal cylinder of 5 cm in diameter and initially at a temperature about 150 °C. the eylinder is suddenly immersed in liquid with temperature at 50 °C and heat transfer coeflicient about 2000 W/m.°C. Under typical operation conditions the center temperature and surface temperature are measured to be 110 °C and 90 °C after 1 minute, respectivielly. Calculate the thermal conductivity for this material.
What is concurrent engineering how it differs from the sequential design.
Q. Discuss different types of Layout planning in manufacturing unit with example.
A customer has recently tightened the specs for a part your company supplies. The specs are nowmuch tighter than the machine being used for the job is capable of. Briefly identify alternativesyou might consider to resolve this problem.
Sketching is required in all three phases, ideation, refinement and implantation of the design process. O True False
Cushion is an area throughout some workstations & tasks in manufacturing processes. Evaluate the statement below, agree or disagree? "Larger cushion is always better for manufacturing processes"
A Company produces mechanical probe to update OWSVS (Offensive-Warfare-Support- Vehicle- Systems). For the process of making a mechanical probe, 10 process steps are needed. It is calculated that the scrap rate and rework rate are 12% and 9%, respectively. The average setup time, average machining (operational) time and the average non- operational time can be expressed as: 2.4 hours, 9.6 minutes, and 9.6 hours, respectively. a) With a batch size of 520 mechanical probes, what must be Manufacturing Lead Time (MLT) in hours? b) With 8 hours per shift and two shifts per day, if the plant works 5 days a week, what is the MLT in weeks? c) If the availability factor can be expressed as 81%, then what must be the value of MLT? (in hours and weeks)
Suppose your company has just found $100,000 worth of outdated inventory in an old warehouse (this is the original manufacturing cost). Your boss asks you to consider two options: (1) re-engineer the outdated parts at a cost of $30,000, and ideally resell them for $60,000, or (2) scrap them for $15,000 cash (which is certain) in a second-hand market. What advice would you give your boss? Explain in your own words and give the data that supports your answer.